Capturing braking energy by regeneration into an onboard energy storage unit offers the potential to reduce significantly the fuel consumption of vehicles. A common technique is to generate electricity in the motors of a hybrid electric vehicle when braking, and to use this to charge an onboard electrochemical battery. However, such batteries are costly, bulky, and generally not amenable to fast charging as this affects battery life and capacity. In order to overcome these problems, a mechanical energy storage system capable of accepting and delivering surges of power is proposed and investigated. A scale physical model of the system, based around a flywheel, a planetary gear set, and a brake, was built and operated in a laboratory. Tests showed that the proposed system could be used to store and provide braking energy between a flywheel and a vehicle, the latter emulated by an air-drag dynamometer. This validated the operating principle of the system and its computational model. Further, a computational analysis of a full-size vehicle incorporating the mechanical energy storage system was conducted. The results showed that the utilization of this system in a vehicle, when compared with a conventional vehicle, led to reductions in emissions and fuel consumption.
ChanC. C.Electric vehicles charge forward. IEEE Power Energy Mag., 2004, 2(6), 24–33.
2.
DuobaM.NgH.LarsenR.In-situ mapping and analysis of the Toyota Prius HEV engine. In Proceedings of the Future Transportation Technology Conference and Exposition, Costa Mesa, California, USA, 21–23 August 2000, SAE paper 2000-01-3096, 2000.
3.
LaveL. B.MacLeanH. L.An environmental- economic evaluation of hybrid electric vehicles: Toyota's Prius vs. its conventional internal combustion engine Corolla. Transpn Res. Part D - Transport and Environment, 2002, 7(2), 155–162.
4.
TaniguchiA.FujiokaN.IkomaM.OhtaA.Development of nickel/metal-hydride batteries for EVs and HEVs. J. Power Sources, 2001, 100(1–2), 117–124.
5.
ChalkS. G.MillerJ. F.Key challenges and recent progress in batteries, fuel cells, and hydrogen storage for clean energy systems. J. Power Sources, 2006, 159(1), 73–80.
6.
KardenE.PloumenS.FrickeB.MillerT.SnyderK.Energy storage devices for future hybrid electric vehicles. J. Power Sources, 2007, 168(1), 2–11.
7.
OzakiT.YangH. B.IwakiT.TanaseS.SakaiT.FukunagaH.MatsumotoN.KatayamaY.TanakaT.KishimotoT.KuzuharaM.Development of Mg-containing Mm Ni5-based alloys for low-cost and high-power Ni-MH battery. J. Alloys Compounds, 2006, 408–412, 294–300.
8.
GiffordP.AdamsJ.CorriganD.VenkatesanS.Development of advanced nickel metal hydride batteries for electric and hybrid vehicles. J. Power Sources, 1999, 80(1–2), 157–163.
9.
OmanH.New energy management technology gives hybrid cars long battery life. In Proceedings of the 34th Intersociety Energy Conversion Engineering Conference, Vancouver, Canada, 1999, SAE paper 1999-01-2468, 1999.
10.
AanstoosT. A.KajsJ. P.BrinkmanW. G.LiuH. P.OurouaA.HayesR. J.HearnC.SarjeantJ.GillH.High voltage stator for a flywheel energy storage system. IEEE Trans. Magn., 2001, 37(1), 242–247.
11.
BolundB.BernhoffH.LeijonM.Flywheel energy and power storage systems. Renewable Sustainable Energy Rev., 2007, 11(2), 235–258.
12.
SuzukiY.KoyanagiA.KobayashiM.ShimadaR.Novel applications of the flywheel energy storage system. Energy, 2005, 30(11–12), 2128–2143.
13.
Van MierloJ.Van den BosscheP.MaggettoG.Models of energy sources for EV and HEV: Fuel cells, batteries, ultracapacitors, flywheels and engine-generators. J. Power Sources, 2004, 128(1), 76–89.
14.
DietrichP.EberleM. K.HörlerH. U.Results of the ETH-hybrid III-vehicle project and outlook. In Proceedings of the International Congress and Exposition, Detroit, Michigan, USA, 1–4 March 1999, SAE paper 1999–01-0920, 1999.
15.
ShenS. W.SerrarensA.SteinbuchM.VeldpausF.Coordinated control of a mechanical hybrid driveline with a continuously variable transmission. JSAE Rev., 2001, 22(4), 453–461.
16.
ShenS. W.VroemenB.VeldpausF.IdleStop and Go: A way to improve fuel economy. Veh. System Dynamics, 2006, 44(6), 449–476.
17.
VroemenB.SerrarensA.VeldpausF.Hierarchical control of the zero inertia powertrain. JSAE Rev., 2001, 22(4), 519–526.
18.
ShahS.The design and development of a high speed composite flywheel for hybrid vehicles. PhD Thesis, Department of Mechanical Engineering, Imperial College, London, 2006.
19.
HofmannD. A.Gearing for high speed motors. In Proceedings of the IEE Colloquium on High speed bearings for electrical machines, Digest 1997/164, 25 April 1997, pp. 3/1–3/13 (IEE, London).
20.
MantriotaG.Theoretical and experimental study of a power split continuously variable transmission system, Part 1. Proc. Instn Mech. Engrs, Part D: J. Automobile Engineering, 2001, 215(7), 837–850.
21.
SantoroM.A hybrid-propulsion powertrain with planetary gear set for a WD vehicle: analysis of power flows and energy efficiency. Report, Dresden University of Technology, Dresden, Germany, 1998.
22.
Diego-AyalaU.An investigation into hybrid power trains for vehicles with regenerative braking. PhD Thesis, Department of Mechanical Engineering, Imperial College, London, 2007.
23.
NorthR. J.OchiengW. Y.QuddusM. A.NolandR. B.PolakJ. W.Development and testing of a vehicle performance and emissions monitoring system. Proc. Instn Civ. Engrs, Transport, 2005, 158(3), 167–177.
24.
EEC Directive 90/C81/01, EEC emission cycles, emission test cycles for the certification of light duty vehicles in Europe, 1990.
25.
AndréM.Real-world driving cycles for measuring cars pollutant emissions - part A: the ARTEMIS European driving cycles. Report INRETS-LTE 0411, Institut National de Recherche SW 65 Transports et leur Securité, Bron, France, June 2004.
26.
KlaassenT.VroemenB.BonsenB.van de MeerakkerK.SteinbuchM.VeenhuizenP. A.Modeling and simulation of an electromechanically actuated pushbelt type continuously variable transmission. In Proceedings of the Third IFAC Symposium on Mechatronic systems, Sydney, Australia, 6–8 September 2004, pp. 241–246 (IFAC, Sydney).
27.
LeeH.KimH.Improvement in fuel economy for a parallel hybrid electric vehicle by continuously variable transmission ratio control. Proc. IMechE, Part D: J. Automobile Engineering, 2005, 219(1), 43–51.
28.
Osornio CorreaC.Characterisation of a flexible transmission for a hybrid electrical vehicle optimising power train performance (in Spanish). PhD Thesis, Department of Mechanical Engineering, Universidad Nacional Autónoma de México, 2006.
29.
SolticP.GuzzellaL.Performance simulations of engine-gearbox combinations for light-weight passenger cars. Proc. Instn Mech. Engrs, Part D: J. Automobile Engineering, 2001, 215(2), 259–271.
30.
EMEP/CORINAIR Emission Inventory guidebook - 2006. Technical Report 11/2006, European Environment Agency, Copenhagen, Denmark, 21 December 2006, p. 29.
