Development of an electronic control unit for a compressed natural gas engine,based on circuit simulation and modelling

Abstract

An electronic control unit (ECU) is designed for a compressed natural gas (CNG) engine on the basis of circuit simulation and modelling. The ignition drive circuit and power-off delay circuit are discussed, with emphasis on circuit simulation, and resistance matching for the sensor processing circuit is described. Design of the software of the CNG control system is based on modelling. A TargetLink model of an air—fuel ratio closed-loop control system is presented. The CNG ECU has been applied successfully in bench tests. The results of bench tests have shown that the hardware meets CNG control system requirements; actuators can be controlled precisely, and the performance of the CNG engine can reach design targets. Circuit simulation and modelling are good methods for developing the ECU design for CNG engine systems. Quality of hardware and software design can be ensured, and the development cycle and costs can be reduced.

Keywords

electronic control unit compressed natural gas engine hardware design circuit simulation bench tests

Get full access to this article

View all access options for this article.

References

Liu

S. H.

Wang

Z. Y.

Ren

‘Development of compressed natural gas/diesel dual-fuel turbocharged compression ignition engine.’

Proc. IMechE, Part D: J. Automobile Engineering 217 (2003): 839–845.

Huang

Shiga

Ueda

Nakamura

Ishima

Obokata

Tsue

Kono

‘Correction of ignitability with injection timing for direct injection combustion fuelled with compressed natural gas and gasoline.’

Proc. IMechE, Part D: J. Automobile Engineering 217 (6) (2003): 499–506 DOI: 10.1243/095440703766518122.

Paolo

Maione

Ameorese

De Matthaeis

‘Modeling and predictive control of a new injection system for compressed natural gas engines. In Proceedings of the 2006 IEEE International Conference on Control Applications, Munich, Germany, 4–6 October 2006, pp. 1651–1656.

Rousseau

Lemoult

Tazerout

‘Combustion characterization of natural gas in a lean burn spark-ignition engine.’

Proc. IMechE, Part D: J. Automobile Engineering 213 (D5) (1999): 481–489 DOI: 10.1243/0954407991527044.

Shi

L. L.

Bing

Fang

H. M.

Zuo

H. H.

‘Development and calibration on an electronic control system of CNG engine. In Proceedings of the 2006 IEEE International Conference on Vehicular Electronics and Safety,’ (2006): 204–208.

Zhao

H. W.

Chen

Zang

X. B.

Liu

D. Y.

Wang

Q. N.

‘Research on multi-energy hybrid electric vehicle powertrain controller based on CAN network. In Proceedings of the IEEE Conference on Intelligent Transportation Systems,’ (2003): 938–941.

Dellino

Lino

Meloni

Rizzo

‘Multidisciplinary design optimization of a pressure controller for CNG injector systems. In Proceedings of the 2006 IEEE Conference on Computer Aided Control Systems Design, Munich, Germany, 4–6 October 2006, pp. 2689–2694.

Tan

W. C.

S. T.

Yang

‘Application of circuit simulation in hardware design for electronic control high pressure common-rail fuel system for diesel engine.’

Chin. J. Mech. Engng 18 (2005): 613–616.

Wang

Q. S.

Zhao

Y. P.

Zhao

Z. W.

‘Research on energy simulation model for vehicle ignition system. In Proceedings of the IEEE Vehicle Power and Propulsion Conference (VPPC), Harbin, People's Republic of China, 3–5 September 2008, paper H08090.

10.

Y. J.

B. H.

‘Nonlinear modeling of spark plugs ignition process and parameter identification.’

Trans. CSICE 17 (1999): 281–284.

11.

S. T.

Zhong

X. L.

Yang

Gong

Y. M.

Zhuo

‘Study on the model-based development for the electrically controlled system of a high-pressure common-rail diesel engine.’

Proc. IMechE, Part D: J. Automobile Engineering 220 (3) (2006): 359–366 DOI: 10.1243/09544070D21004.