The research reported in this paper aims to simulate the road-holding of a virtual vehicle using multi-body simulation to estimate both the contact forces between the tyre and ground and the roll motion when cornering. Furthermore, the effect of the characteristic angles on the variation in the forces of the tyre in contact with the ground is studied to determine optimal values for these angles. Emphasis is placed on an average-class vehicle, of which both the external dimensions and mass are chosen appropriately, with a McPherson suspension mounted on both the front and the rear. The characteristic values of the camber and toe-in angles, in both the front and the rear, are optimized for motion in the curve under constant traction. The results of numerical simulation are compared with results from the theory of stability in the curve (given the vertical configuration of the vehicle).
MántarasD. A.LuqueP.VeraC.‘Development and validation of a three-dimensional kinematic model for the McPherson steering and suspension mechanisms.’Mechanism Mach. Theory39 (6) (2004): 603–619.
3.
HabibiH.ShiraziK. H.ShishesazM.‘Roll steer minimization of McPherson-strut suspension system using genetic algorithm method.’Mechanism Mach. Theory43 (1) (2008): 57–67.
4.
XinL.-L.LiangJ.-H.WenB.-C.‘Front wheel alignment parameters analysis of McPherson suspension based on I-DEAS.’Dongbei Daxue Xuebao (J. Northeastern Univ.)29 (Suppl.) (2008): 165–168.
5.
SimionescuP. A.BealeD.‘Synthesis and analysis of the five-link rear suspension system used in automobiles.’Mechanism Mach. Theory37 (9) (2002): 815–832.
6.
DaogaoW.KeqiangL.XiaofengW.DafengJ.YintaoW.‘Research on the precise calculation and control strategy of front wheel toe-in of vehicles.’ In Proceedings of the IEEE International Conference onVehicular electronics and safety, 14–16 October 2005, pp. 12–14 (IEEE, New York).
7.
ModakJ. P.BelkhodeP. N.BodhankarD.HimteR. L.WashimkarP. V.‘Modeling and analysis of front suspension for improving vehicle ride and handling.’ In Proceedings of the First International Conference onEmerging trends in engineering and technology (ICETET ‘08), 16–18 July 2008, pp. 731–734 (IEEE, New York).
8.
MeissonnierJ.FaurouxJ. C.GoguG.MontezinC.‘Geometric identification of an elastokinematic model in a car suspension.’Proc. IMechE, Part D: J. Automobile Engineering220 (9) (2006): 1209–1220 DOI: 10.1243/09544070JAUTO239.
9.
MeissonnierJ.MetzP.FaurouxJ.-C.GoguG.MontezinC.‘Iterative identification of stiffness parameters in a car suspension elastokinematic model.’Proc. IMechE, Part D: J. Automobile Engineering220 (11) (2006): 1477–1489 DOI: 10.1243/09544070JAUTO327.
10.
JiangG.ZhouK.‘Kinematic characteristic of unique suspension system for wagon.’Jixie Gongcheng Xuebao (Chin. J. Mech. Engng)44 (4) (2008): 217–221.
11.
FicarraG.Virz░ MariottiG.‘Optimization of wheel characteristic angles by numerical simulation, with verify of Pacejka formulas.’Mobility Veh. Mech.30 (4) (2004): 7–19.
12.
FicarraG.Virzì MariottiG.‘Comportamento dinamico di un autoveicolo. Influenza degli angoli caratteristici delle ruote.’Ingegn. Autoveicolo57 (3–4) (2004): 57–64.
13.
De GaetanoS.GuerreraG.Virz░ MariottiG.‘Dynamic simulation of the behaviour of a ‘light vehicle’ by disabled users, tested on a virtual road.’ In Proceedings of the 19th Conference onScience and motor vehicles, Belgrade, Serbia, 26–28 May 2003 (JUMV, Belgrade, Serbia).
14.
Virz░ MariottiG.LopezF.TriscariF.‘Studio di un ammortizzatore a taratura variabile per una sospensione di autovettura gran turismo.’ATA (2002), 55(5–6), 188–195.
15.
PacejkaH. B.‘Proceedings of the 1st International Colloquium onTyre models for vehicle dynamics, Delft, The Netherlands, 21–22 October 1993 (Taylor & Francis).
MillikenW. F.MillikenD. L.Race car vehicle dynamics (SAE International1995).
19.
MancosuF.Da ReD.MinenD.‘Non linear rolling tyre model for dynamic simulation.’ In Proceedings of the 32nd International Symposium on Automotive technology and automation (ISATA): advances in automotive and transportation technology (Ed. RollerD.), Vienna, Austria, 14–18 June 1999, pp. 61–68 (ISATA, Vienna, Austria).
20.
FentonJ.Handbook of automotive powertrain and chassis design (Professional Engineering Publishing Limited1998).
