Titanium alloys are used extensively in the aerospace industry and are generally classified as ‘hard to machine’. The combination of high strength at elevated temperatures, low thermal conductivity, low modulus of elasticity, and high chemical affinity with all available cutting tool materials means that there are inherent difficulties when machining. The extensive literature detailing all aspects of the machinability of titanium alloys is briefly reviewed; however, little of this refers specifically to surface integrity, which is critical to industries such as aerospace. This paper focuses on the effects that insert geometry had on tool life and workpiece surface integrity when cutting speed, feed rate, and depth of cut were varied. Specifically the effects of edge radius, side cutting edge angle, and edge land are considered. The findings show that whatever combination of tool geometry and operating parameters were used, the surface integrity is remarkably similar, even at relatively high cutting speeds and feed rates.
DonachieM. J.DonachieS. J.Superalloys: A technical guide, 2002 (ASM International, Ohio).
7.
ZlatinN.FieldM.Procedures and precautions in machining titanium alloys. Titanium Sci. Technol., 1973, 1, 489–501.
8.
NarutakiN.MurakoshiA.Study on machining of titanium alloys. Ann. CIRP, 1983, 32(1), 65–69.
9.
RibeiroM. V.MoreiraM. R. V.FerreiraJ. R.Optimization of titanium alloy (6Al-4V) machining. J. Mater. Process. Technol., 2003, 143-144, 458–463.
10.
de lacalleLopez L. N.PerezJ.LlorenteJ. I.SanchezJ. A.Advanced cutting conditions for the milling of aeronautical alloys. J. Mater. Process. Technol., 2000, 100, 1–11.
11.
Che-HaronC. H.Tool life and surface integrity in turning titanium alloy. J. Mater. Process. Technol., 2001, 118, 231–237.
12.
HartungP. D.KramerB. M.Tool wear in titanium machining. Ann. CIRP, 1982, 31(1), 75–80.
DiackM.-I.HamannJ. C.Le MaitreF.JoyceR.An analysis of tool wear mechanisms in high speed cylindrical turning of titanium alloys. In Titanium '95: Science and technology (Eds. BlenkinsopP. A.EvansW. J.FlowerH.), 1995, pp. 763–769 (Cambridge University Press, Cambridge, UK).
15.
JawaidA.Che-HaronC. H.FallahA.Tool wear in machining of titanium alloy Ti 6246. In Proceedings of the Third International Conference on Progress of cutting and grinding, Osaka, Japan, November 1996, pp. 126–131.
DearnleyP. A.GrearsonA. N.Evaluation of principal wear mechanisms of cemented carbides and ceramics used for machining titanium alloy IMI 318. Mater. Sci. Technol., 1986, 2, 47–58.
18.
DearnleyP. A.GrearsonA. N.AucoteJ.Wear mechanisms of cemented carbides and ceramics used for machining titanium alloys. High Tech. Ceramics, 1987, 38, 2699–2712.
19.
WalterJ. L.SkellyD. W.MinnearW. P.Ion implantation of cobalt-tungsten carbide tools for machining titanium. Wear, 1993, 170, 79–92.
20.
LeeM.The failure characteristics of cutting tools machining titanium alloys at high speed. In Proceedings of Titanium and Physical Metallurgy Committees of the AIME Louisville, Kentucky13-15 October 1981, pp. 275–287.
21.
KahlesJ. F.FieldM.EylonD.FroesF. H.Machining of titanium alloys. J. Metals, April 1985, 27–35.
22.
BhaumikS. K.DivakarC.SinghA. K.Machining Ti-6Al-4V alloy with a wBN-cBN composite tool. Mater. Des., 1995, 16(4), 221–226.
23.
ColwellL. V.TruckenmillerW. C.Cutting characteristics of titanium and its alloys. Mech. Engng, 1953, 76, 461–466, 480.
24.
KomanduriR.ReedW. R.Jr.Evaluation of carbide grades and a new cutting geometry for machining titanium alloys. Wear, 1983, 92, 113–123.
25.
WangZ. M.EzugwuE. O.Performance of PVD-coated carbide tool when machining Ti-6Al-4V. Tribology Trans., 1997, 40, 81–86.
26.
KosterW. P.FieldM.Effect of machining variables on the surface and structural integrity of titanium. In North American metalworking research conference, Vol. 2, 1973, pp. 67–87.
JeelaniS.RamakrishnanK.Surface damage in machining titanium 6Al-2Sn-4Zr-2Mo alloy. J. Mater. Sci., 1985, 20, 3245–3252.
29.
MachadoA. R.WallbankJ.PashbyI. R.EzugwuE. O.Tool performance and chip control when machining Ti6Al4V and Inconel 901 using high pressure coolant supply. Machining Sci. Technol., 1998, 2, 1–12.
30.
KomanduriR.Some clarifications on the mechanics of chip formation when machining titanium alloys. Wear, 1982, 76, 15–34.
KishawyH. A.BeczeC. E.McIntoshD. G.Tool performance and attainable surface quality during the machining of aerospace alloys using self-propelled rotary tools. J. Mater. Process. Technol., 2004, 152, 266–271.
33.
MachadoA. R.WallbankJ.Machining of titanium and its alloys - a review. Proc. Instn Mech. Engrs, Part B: J. Engineering Manufacture, 1990, 204, 53–60.
34.
Che-HaronC. H.JawaidA.The effect on surface integrity of titanium alloy Ti-6% Al-4% V. J. Mater. Process. Technol., 2005, 166, 188–192.
35.
YangX.LiuC. R.Machining titanium and its alloys. Machining Sci. Technol., 1999, 3(1), 107–139.
36.
HughesJ. I.SharmanA. R. C.RidgwayK.The effect of tool edge preparation on tool life and workpiece surface integrity. Proc. Instn. Mech. Engrs, Part B: J. Engineering Manufacture, 2004, 218(B9), 1113–1123.
37.
GrantP. V.LordJ. D.WhiteheadP. S.The measurement of residual stresses by the incremental hole drilling technique. National Physical Laboratory Good Practice Guide No. 53, August, 2002 (National Physical Laboratory, UK).
38.
ISO 3685 Specification for tool life with single point turning tools, 1993 (International Standardization Organization, Geneva, Switzerland).
39.
EzugwuE. O.WangZ. M.Titanium alloys and their machinability - a review. J. Mater. Process. Technol., 1997, 68, 262–274.
40.
ThieleJ. D.MelkoteS. N.Effect of edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel. J. Mater. Process. Technol., 1999, 94, 216–226.
41.
Munoz-EscalonaP.CassierZ.Influence of the critical cutting speed on the surface finish of turned steel. Wear, 1998, 218, 103–109.
42.
MotonishiS.HaraY.IsodaS.ItohH.TsumoriY.Study on machining of titanium and its alloys. Kobelco Technol. Rev., 1987, 2, 28–31.
43.
NgE.-G.AspinwallD. K.The effect of workpiece hardness and cutting speed on the machinability of AISI H13 hot work die steel when using PCBN tooling. Trans. ASME, J. Mfg Sci. Engng, 2002, 124, 588–594.
44.
RaoB.ShinY. C.Analysis on high-speed face-milling of 7075-T6 aluminium using carbide and diamond cutters. Int. J. Mach. Tools Mf., 2001, 41, 1763–1781.
45.
DahlmanP.GunnbergF.JacobsonM.The influence of rake angle, cutting speed and cutting depth on residual stresses in hard turning. J. Mater. Process. Technol., 2004, 147, 181–184.
46.
SaoubiR. M.OuteiroJ. C.ChangeuxB.LebrunJ. L.DiasMorao A.Residual stress analysis in orthogonal machining of standard and resulfurised AISI 316L steels. J. Mater. Process. Technol., 1999, 96, 225–233.
47.
El-WardanyT. I.KishawyH. A.ElbestawiM. A.Surface integrity of die material in high speed machining, Part 2. Microhardness variations and residual stress. Trans. ASME, J. Mfg Sci. Engng, 2000, 122, 632–641.
