Piping elbows with cracks Part 1: A parametric study of the influence of crack size on limit loads due to pressure and opening bending

Abstract

Finite element analyses of cracked short-radius piping elbows are reported. Both axial and circumferential cracks, centred about the bend crown or intrados respectively, are considered. The defects are internal, with depth-thickness ratios a/t in the range 0.25 ≤ a/t ≤ 1.0. Since the aim is to assess limit loads, the analysis assumes elastic-perfectly plastic material behaviour with no geometric non-linearities. The loadings considered are (a) opening bending moment, (b) internal pressure and (c) combined loading of steady pressure, set at the design value of the pipe elbow, with a superimposed monotonically increasing opening bending moment.

For each type of loading, the general component behaviour, by consideration of the global deformation with increasing load, is reported. Limit load values for each case are presented and the relative reductions in load-carrying capacity, compared with that predicted for a defect free elbow of the same material and dimensions, are given.

Keywords

piping elbows cracks crack size limit loads pressure opening bending

Get full access to this article

View all access options for this article.

References

Assessment of the integrity of structures containing defects. Document R/H/R6, Revision 3, up to and including Amendment 9, Nuclear Electric Limited, August 1998.

Miller

A. G.

Review of limit loads of structures containing defects. Int. J. Pressure Vessels Piping, 1988, 32, 197–227.

Zahoor

Ductile Fracture Handbook, Vols 1—3, Publication EPRI NP-6301-D/N14, 1989, 1990, 1991 (Electric Power Research Institute, Palo Alto, California).

Griffiths

J. E.

The effect of cracks on the limit load of pipe bends under in-plane bending: Experimental study. Int. J. Mech. Sci., 1979, 21 (2), 119–130.

Miller

A. G.

The plastic collapse of cracked pipe bends under internal pressure or in-plane bending. CEGB Report TPRD/B/0806/R86, Central Electricity Generating Board, December 1986.

Chattopadhyay

Dutta

B. K.

Kushwaha

H. S.

Mahajen

S. C.

Kakodkar

Limit load analysis and safety assessment of an elbow with a circumferential crack under a bending moment. Int. J. Pressure Vessels Piping, 1995, 62, 109–116.

Moulin

Chapuliot

Drubay

Fracture assessment of piping and elbows. In Proceedings of the International Conference on

Pressure Vessels and Piping, Vol. 1, 1996, pp. 281–291 (American Society of Mechanical Engineers, New York).

Yahiaoui

Moffat

D. G.

Moreton

D. N.

Damage assessment of piping elbows loaded by steady internal pressure and dynamic in-plane or out-of-plane bending. In Proceedings of the Eighth International Conference on

Pressure Vessel Technology, Vol. 1, Montreal, 1996, pp. 361–375 (American Society of Mechanical Engineers, New York).

Yahiaoui

Moffat

D. G.

Moreton

D. N.

Piping elbows with cracks. Part 2: Global finite element and experimental plastic loads under opening bending. J. Strain Analysis, 2000, 35 (1), 47–57.

10.

Patran, Versions 3, 5 and 6, 1993–97 (PDA Engineering, Santa Ana, California).

11.

Abaqus/Standard - Abaqus/Post User Manuals, Versions 5 and 6, 1996 (Hibbit, Karlsson and Sorensen, Pawtucket, Rhode Island).

12.

Calladine

C. R.

Limit analysis of curved tubes. J. Mech. Eng. Sci., 1974, 16 (2), 85–87.

13.

Spence

Findlay

G. E.

Limit loads for pipe bends under in-plane bending. In Proceedings of the Second International Conference on

Pressure Vessel Technology, San Antonio, Texas, 1973, pp. 393–399.

14.

ASME, Boiler and Pressure Vessel Code, section III, 1992.

15.

Goodall

I. W.

Lower bound limit analysis of curved tubes loaded by combined internal pressure and in-plane bending moment. CEGB report RD/B/N4360, Central Electricity Generating Board, August 1978.

16.

Rodabaugh

E. C.

Interpretive report on limit analysis and plastic behaviour of piping products. Welding Research Council Bulletin 254, November 1979, pp. 65–82.

17.

Bolt

Greenstreet

W. L.

Experimental determinations of plastic collapse loads of pipe elbows. In Proceedings of the International Conference on

Pressure Vessels and Piping, 1972, paper 71-PVP-37, pp. 2–12 (American Society of Mechanical Engineers, New York).

18.

Chan

K. L. C.

Boyle

J. T.

Spence

Approximate limit loads for pipe bends with end constraints. In Applied Solid Mechanics (Eds Tooth

A. S.

Spence

), 1984, pp. 275–284 (Elsevier Applied Science, London).

19.

Ainsworth

R. A.

Plastic collapse load of a thin walled cylinder under axial load with a fully circumferential crack. Advice Note EPD/GEN/EAN/0085/98, NEL Engineering, June 1998.