The thresholds and depths of ablation of carbon [carbon nanotubes (CNTs) or graphene nanoplatelets (GNPs)] reinforced Al2O3 composites were compared and correlated with those of monolithic Al2O3 using femtosecond pulsed laser irradiation (λ = 1027 nm, τP = 380 fs). These composites were processed using a spark plasma sintering method (Ts = 1500°C, τs = 10 min and P = 40 MPa) through which highly densified (more than 97%) composites were fabricated. The optical absorbance of each composite improved in the wavelength range from ultraviolet to near infrared. Compared with the corresponding values for monolithic Al2O3, the ablation thresholds of CNT/Al2O3 and GNP/Al2O3 were 50 and 75% lower respectively, and their ablation depths were two to three times deeper.
BaughmanR. H., ZakhidovA. A. and de HeerW. A.: ‘Carbon nanotubes – the route toward applications’, Science, 2002, 297, (5582), 787–792. doi: 10.1126/science.1060928
2.
WeiD. and LiuY.: ‘Controllable synthesis of graphene and its applications’, Adv. Mater., 2010, 22, 3225–3241. doi: 10.1002/adma.200904144
3.
LiQ., RottmairC. A. and SingerR. F.: ‘CNT reinforced light metal composites produced by melt stirring and by high pressure die casting’, Compos. Sci. Technol., 2010, 70, 2242–2247. doi: 10.1016/j.compscitech.2010.05.024
4.
InamF., ReeceM. J. and PeijsT.: ‘Structural and chemical stability of multiwall carbon nanotubes in sintered ceramic nanocomposite’, Adv. Appl. Ceram., 2010, 4, (109), 240–245. doi: 10.1179/174367509X12595778633336
5.
PorwalH., GrassoS. and ReeceM. J.: ‘Review of graphene-ceramic matrix composite’, Adv. Appl. Ceram., 2013, 112, (8), 443–454. doi: 10.1179/174367613X13764308970581
6.
WangZ. Z., KwonD. J., GuG. Y., KimH. S., KimD. S., LeeC. S., DeVriesK. L. and ParkJ. M.: ‘Mechanical and interfacial evaluation of CNT/polypropylene composites and monitoring of damage using electrical resistance measurements’, Compos. Sci. Technol., 2013, 81, 69–75. doi: 10.1016/j.compscitech.2013.04.001
7.
PeigneyA., LaurentCh., DumortierO. and RoussetA.: ‘Carbon nanotubes-Fe-alumina nanocomposites. Part 1: influence of the Fe content on the synthesis of Powders’, J. Eur. Ceram. Soc., 1998, 18, (14), 1995–2004. doi: 10.1016/S0955-2219(98)00141-1
8.
ZhanG. D., KuntzJ. D., WanJ. and MukherjeeA. K.: ‘Single-wall carbon nanotubes as attractive toughening agents in alumina-based nanocomposites’, Nat. Mater., 2003, 2, 38–42. doi: 10.1038/nmat793
9.
LiuJ., YanM. and JiangK.: ‘Mechanical properties of graphene platelet-reinforced alumina ceramic composites’, Ceram. Int., 2013, 39, 6215–6221. doi: 10.1016/j.ceramint.2013.01.041
10.
SikderP., PramanickA., SarkarS., DasS., DeyP. P. and DasP. K.: ‘Indentation size effect and wear characteristics of spark plasma sintered, hard MWCNT/Al2O3 nanocomposites’, Adv. Appl. Ceram., 2006, in press.
11.
PerrieW., RushtonA., GillM., FoxP. and O'NeillW.: ‘Femtosecond laser micro-structuring of alumina ceramic’, Appl. Surf. Sci., 2005, 248, 213–217. doi: 10.1016/j.apsusc.2005.03.005
12.
MajumdarJ. D. and MannaI.: ‘Laser material processing’, Int. Mater. Rev., 2011, 56, (5/6), 341–388. doi: 10.1179/1743280411Y.0000000003
13.
IakoubovskiiK., MinamiN., KimY., MiyashitaK., KazaouiS. and NaliniB.: ‘Midgap luminescence centers in single-wall carbon nanotubes created by ultraviolet illumination’, Appl. Phys. Lett., 2006, 89, 173108. doi: 10.1063/1.2364157
14.
LimD. S., YouD. H., ChoiH. J., LimS. H. and JangH.: ‘Effect of CNT distribution on tribological behavior of alumina-CNT composites’, Wear, 2005, 259, 539–544. doi: 10.1016/j.wear.2005.02.031
15.
Al-Mosawi AliI., Al-Maamori MohammadH. and Al MayaleeKhalidahH.: ‘Spectroscopic studies of polyester-carbon black composites’, Res. J. Mater. Sci., 2013, 1, (2), 10–14.
16.
TakayamaH. and MaruyamaT.: ‘Femtosecond laser ablation of wide band-gap materials’, Appl. Surf. Sci., 2012, 261, 705–707. doi: 10.1016/j.apsusc.2012.08.084
17.
GamalyE. G., RodeA. V. and Luther-DaviesB.: ‘Surface integrity characteristics in wire-EDM of Inconel 718 at different discharge energy’, Phys. Plasmas, 2002, 9, (3), 949–957. doi: 10.1063/1.1447555
18.
RizviN. H.: ‘Femtosecond laser micromachining current status and applications’, Riken Rev., 2003, 50, 107–112.
