Electrophoretic deposition (EPD) was used for the fabrication of piezoelectric [lead zirconate titanate (PZT)] thick films on alumina substrates. The EPD was performed in constant current mode from an ethanol based suspension consisting of PZT and PbO particles. The influence of addition of ethyl cellulose (EC) and sintering temperature on the thickness, density, homogeneity and functional response of PZT thick films is studied. Results show that the highest electromechanical performance is obtained for the PZT thick films sintered at 900 or 950°C, with a thickness coupling factor kt of 50%. The addition of EC influenced the thickness of the PZT thick films but had only minor effect on the porosity content for sintering temperatures over 900°C. Moreover, elastic constants of the thick films based on the suspension with EC were lower, which leads to lower acoustic impedance (15 MRa) while maintaining high (kt) value. In this last case, a better acoustic matching can be expected with propagation media such as water or biological tissues for ultrasound medical imaging applications.
GururajaT. R.: ‘Piezoelectrics for medical ultrasonic-imaging’, Am. Ceram. Soc. Bull., 1994, 73, 50–55.
2.
ShungK. K., CannataJ. M. and ZhouQ. F.: ‘Piezoelectric materials for high frequency medical imaging applications: A review’, J. Electroceram., 2007, 19, (1), 139–145.
3.
LethiecqM., LevassortF., CertonD. and Tran-Huu-HueL. P.: ‘Piezoelectric transducer design for medical diagnosis and NDE’, in ‘Piezoelectric and acoustic materials for transducer applications’ (ed. SafariA., et al.,., 191–215; 2008, Boston, MA, Springer.
4.
MarechalP., LevassortF., HolcJ., Tran-Huu-HueL.-P., KosecM. and LethiecqM.: ‘High-frequency transducers based on integrated piezoelectric thick films for medical imaging’, IEEE Trans. Ultrason. Ferroelectr. Freq. Control, 2006, 53, (8), 1524–1533.
5.
Tran-Huu-HueP., LevassortF., Vander MeulenF., HolcJ., KosecM. and LethiecqM.: ‘Preparation and electromechanical properties of PZT/PGO thick films on alumina substrate’, J. Eur. Ceram. Soc., 2001, 21, 1445–1449.
6.
KuscerD., LevassortF., LethiecqM., AbellardA.-P. and KosecM.: ‘Lead-zirconate-titanate thick films by electrophoretic deposition for high-frequency ultrasound transducers’, J. Am. Ceram. Soc., 2012, 95, (3), 892–900.
7.
SarkarP. and NicholsonP. S.: ‘Electrophoretic deposition (EPD): mechanisms, kinetics and application to ceramics’, J. Am. Ceram. Soc., 1996, 79, (8), 1987–2002.
8.
CorniI., RyanM. P. and BoccacciniA. R.: ‘Electrophoretic depostion: from traditional ceramics to nanotechnology’, J. Eur. Ceram. Soc., 2008, 28, (7), 1353–1367.
9.
KuscerD. and KosecM.: ‘Electrophoretic deposition of lead-zirconate-titanate perovskite thick films with low sintering temperature’, Key Eng. Mater, 2009, 412, 101–106.
10.
PardoL., RicoteJ., KosecM., KuscerD. and HolcJ.: ‘Processing of ferroelectric ceramic thick films’, in ‘Multifunctional polycrystalline ferroelectric materials: processing and properties’ (ed. PardoL., et al.,). Springer S edn, 39–61; 2011, New York, Springer.
11.
ReedJ. S.: ‘Introduction to the principles of ceramic processing’; 1995, New York, Wiley Interscience.
12.
KimT., KwonS., YoonH., ChungC. and KimJ.: ‘Fabrication of carbon nanotube paste using photosensitive polymer for field emission display’, Colloids Surf. A, 2008, 313A–314A, 448–451.
13.
LiH., XieZ., ZhangY. and WangJ.: ‘The effects of ethyl cellulose on PV performance of DSSC made of nanostructured ZnO pastes’, Thin Solid Films, 2010, 518, e68–e71.
14.
SelfridgeA. R.: ‘Approximate material properties in isotropic materials’, IEEE Trans. Sonics Ultrason., 1985, 32z, (3), 381–394.
15.
MarechalP., LevassortF., HolcJ., KuščerD., KosecM., FeuillardG. and LethiecqM.: ‘Electromechanical properties of piezoelectric integrated structures on porous substrates’, Ferroelectrics, 2008, 371, (1), 89–97.
16.
AbellardA.-P., LevassortF., KuščerD., GrégoireJ.-M., LethiecqM. and KosecM.: ‘Electrophoretically deposited PZT thick films for high-frequency ultrasound applications’, Proc. 48th Int. Conf. on ‘Microelectronics, devices and materials’ and the Workshop on ‘Ceramic mycrosystems’, Otocec, Slovenia, September 2012, MIDEM Society for Microelectronics, Electronics Components and Materials139–144..
17.
KrimholtzR., LeedomD. and MatthaeiG.: ‘New equivalent circuits for elementary piezoelectric transducers’, Electron. Lett., 1970, 6, (13), 398–399.
18.
LukacsM., OldingT., SayerM., TaskerR. and SherritS.: ‘Thickness mode material constants of a supported piezoelectric film’, J. Appl. Phys., 1999, 85, (5), 2835–2843.
19.
KuscerD., BakaričT., KozlevčarB. and KosecM.: ‘Interactions between lead-zirconate-titanate, polyacrylic acid and polyvinyl butyral in ethanol and their influence on electrophoretic deposition behavior’, J. Phys. Chem B, 2013, 117B, 1651–1659.
20.
ZhitomirskyI.: ‘Cathodic electrodeposition of ceramic and organoceramic materials: Fundamental aspects’, Adv. Colloid Interface Sci., 2002, 97, 279–317.
21.
PhairJ. W.: ‘Rheological analysis of concentrated zirconia pastes with ethyl cellulose for screen printing SOFC electrolyte films’, J. Am. Ceram. Soc., 2008, 91, (7), 2130–2137.
22.
ICFD Data PDF-ICDD: ‘PCPDFWin Version2.2. June 2001’; Newtown Square, PA2002.
BardaineA., BoyP., BellevilleP., AcherO. and LevassortF.: ‘Improvement of composite sol–gel process for manufacturing 40μm piezoelectric thick films’, J. Eur. Ceram. Soc., 2008, 28, (8), 1649–1655.
25.
GentryK. L., ZaraJ. M., Sang-DonB., Chang-BeomE. and SmithS. W.: ‘Thick film sol–gel PZT transducer using dip coating’, Proc. IEEE Int. Ultrasonics Symp., San Juan, Puerto Rico, October 2000, IEEE977–980..
26.
FilouxE., Lou-MoellerR., CalléS., LethiecqM. and LevassortF.: ‘Optimised properties of high frequency transducers based on curved piezoelectric thick films obtained by pad printing process’, Adv. Appl. Ceram., 2013, 112, (2), 75–78.
