The contribution deals with dry sliding wear behaviour of different Fe–Cr–Mo–[Mn]–[Cu] sintered powder metallurgy systems using a pin on disc test. The effect of chemical composition and two different processing conditions, industrial atmosphere at 1453 K (1180°C) and vacuum atmosphere at 1513 K (1240°C) related to a new proposed type of sinterhardening process, was investigated. The wear phenomena and the wear track characteristics were analysed in relation to processing and microstructures of the tested alloys through light and scanning electron microscopy. A delamination and ploughing wear features were observed for all the sintered steels, and sintering in industrial atmosphere led to an oxidation wear features, too. The results showed positive effect of sinterhardening process via suitable modification of microstructure, and this affected the prior particle boundaries on improving the wear resistance of the tested systems.
CiasA. and CzarskiA.: ‘The use of weibull statistics to quantify property variability in Fe–3Mn–0.8C sinter-hardened structurally inhomogeneous steels’, Arch. Metall. Mater., 2013, 58, (4), 1045–1052.
2.
BidulskýR., Actis GrandeM., BidulskáJ., VladoM. and KvačkajT.: ‘Wear mechanism of chromium pre-alloyed sintered steel’, High Temp. Mater. Processes, 2009, 28, 175–180.
3.
MitchellS. C. and CiasA.: ‘Carbothermic reduction of oxides during nitrogen sintering of manganese and chromium steels’, Powder Metall. Prog., 2004, 4, 132–142.
4.
CiasA.: ‘Effect of local sintering microatmosphere on mechanical properties of Fe–3Cr–0.5Mo–0.6C steel’, Powder Metall., 2013, 56, (3), 231–238. doi: 10.1179/1743290112Y.0000000048
5.
FornoI. and Actis GrandeM.: ‘Influence of geometry and cooling rate on properties of sinter-hardened steels’, Acta Metall. Slovaca, 2013, 19, 271–281. doi: 10.12776/ams.v19i4.181
6.
MaccariniM., BidulskyR. and Actis GrandeM.: ‘Analysis and assessment of powder metallurgy techniques for armour elements production’, Acta Metall. Slovaca, 2012, 18, 69–75.
7.
DudrováE., KabátováM., BidulskýR. and WronskiA. S.: ‘Industrial processing, microstructures and mechanical properties of Fe–(2–4)Mn((0,85Mo)–(0,3–0,7)C sintered steels’, Powder Metall., 2004, 47, 181–190.
8.
BidulskyR., Actis GrandeM., KabatovaM. and BidulskaJ.: ‘The effect of varying carbon content and shot peening upon fatigue performance of prealloyed sintered steels’, J. Mater. Sci. Technol., 2009, 25, 607–610. doi: 10.1179/174328408X326066
9.
ChasoglouD., HryhaE. and NyborgL.: ‘Effect of process parameters on surface oxides on chromium-alloyed steel powder during sintering’, Mater. Chem. Phys., 2013, 138, 405–415. doi: 10.1016/j.matchemphys.2012.11.074
10.
‘Expanding opportunities with chromium’, Met. Powder Rep., 1999, 54, 22–24.
11.
EngströmU.: ‘Influence of the sintering temperature on properties of low alloyed high strength PM materials’, in ‘Advances in powder metallurgy and particulate materials’, (ed. EisenW. B. and KassamS.., 204–216; 2001, Princeton, NJ, MPIF.
SeleckáM., ŠalakA. and DanningerH.: ‘The effect of boron liquid phase sintering on properties of Ni–Mo- and Cr-alloyed structural steels’, J. Mater. Proc. Technol., 2003, 141, 379–384. doi: 10.1016/S0924-0136(03)00421-7
14.
‘PM weighed in the balances and found to be economic’, Met. Powder Rep., 2008, 63, 17–19. doi: 10.1016/S0026-0657(08)70038-9
15.
ŠalakA. and SeleckáM.: ‘Manganese in powder metallurgy steels’, 2012, Cambridge, Cambridge International Science Publishing.
16.
BidulskýR. and Actis GrandeM.: ‘Wear resistance of Fe (Cr–Mo)–[0–2%Cu]–0.65% C sintered steels: improvement of the characteristics using high temperature and fast cooling’, High Temp. Mater. Processes, 2008, 27, 249–256. doi: 10.1515/HTMP.2008.27.4.249
17.
BidulskáJ., BidulskýR. and Actis GrandeM.: ‘Effect of new type heat treatment on wear characteristics of high-strength sintered steels’, Acta Metall. Slovaca, 2010, 16, 146–150.
18.
JamesW. B.: ‘What is sinter-hardening?’, ‘Advances in Powder Metallurgy and Particulate Materials 1998, MPIF, Las Vegas, Princeton, 1998, presented at special interest session, unpublished’; 1998.
19.
LindsleyB.: ‘Alloy development of sinter-hardenable compositions’1, ‘Proceedings of the Euro Powder Metallurgy Congress and Exhibition, Euro PM 2007, EPMA, Toulouse’ 107–111; 2007.
20.
LindsleyB. and JamesW. B.: ‘Sinter hardening response of a Cr–Si–Ni–Mo containing steel’1, ‘Euro PM 2005: Powder Metallurgy Congress and Exhibition, EPMA, Prague’, 275–280; 2005.
21.
LindsleyB.: ‘Sinter-hardening response of leaner alloy systems’, ‘Advances in Powder Metallurgy and Particulate Materials - 2009, PowderMet 2009, MPIF, Las Vegas’, 785–796; 2009.
22.
‘Friction, lubrication, and wear technology’ ‘ASM handbook’, 1992, Materials Park, OH, ASM International.
23.
DudrováE., KabátováM., MitchellS., BidulskýR. and WronskiA. S.: ‘Microstructure development in Fe–Mn–C compacts resulting from step sintering’, Powder Metall., 2010, 53, 244–250. doi: 10.1179/003258909X12502872942417
24.
BidulskyR., Actis GrandeM., HryhaE. and BidulskaJ.: ‘The effect of manganese on microstructure development and diffusion characteristics in admixed Fe–Mn–C sintered steels’3, ‘Proceedings of the World Powder Metallurgy Congress and Exhibition, World PM 2010’, EPMA, Florence, 2010, code 105571.
25.
NavaraE.: ‘Alloying of sintered steel by manganese’1, ‘Proc. VIth International PM Conference, ČSSR, Brno’, 143–147; 1982.
26.
ŠalakA.: ‘Diffusion induced grain boundary migration in alloying iron powders with manganese vapours’, Kovove Mater., 1989, 27, 159–170.
27.
KabatovaM., DudrovaE., WronskiA. S. and BidulskyR.: ‘Fatigue crack initiation and short crack growth in sintered Fe–1.5Cr–0.2Mo–0.7C steel’7, ‘Powder Metall. Prog.’ 20–34; 2007.
28.
DudrovaE., KabatovaM., BuresR., BidulskyR. and WronskiA. S.: ‘Processing, microstructure and properties of 2–4% Mn and 0.3/0.7% C sintered steels’, Kovove Mater., 2005, 43, 404–421.
29.
HryhaE. and NyborgL.: ‘Oxide transformation in Cr–Mn-prealloyed sintered steels: thermodynamic and kinetic’, Metall. Mater. Trans. A, 2014, 45A, 1736–1747. doi: 10.1007/s11661-013-1969-3
30.
HryhaE. and NyborgL.: ‘Process control system for delubrication of PM steels’, Acta Metall. Slovaca, 2012, 18, 60–68.
31.
HryhaE., DudrovaE. and NyborgL.: ‘Critical aspects of alloying of sintered steels with manganese’, Metall. Mater. Trans. A, 2010, 41A, 2880–2897. doi: 10.1007/s11661-010-0357-5
32.
ChawlaN., MurphyT. E., NarasimhanK. S., KoopmanM. and ChawlaK. K.: ‘Axial fatigue behavior of binder-treated versus diffusion alloyed powder metallurgy steels’, Mater. Sci. Eng. A, 2001, A308, 180–188. doi: 10.1016/S0921-5093(00)01990-0
33.
SimchiA. and DanningerH.: ‘Effects of porosity on delamination wear behavior of sintered plain iron’, Powder Metall., 2004, 47, 73–80. doi: 10.1179/003258904225015545
34.
DanningerH., PöttschacherR., BradacS., ŠalakA. and SeyrkammerJ.: ‘Comparison of Mn, Cr and Mo alloyed sintered steels prepared from elemental powders’, Powder Metall., 2005, 48, 23–32. doi: 10.1179/003258905X37567
35.
CamposM., SanchezD. and TorralbaJ. M.: ‘Sintering behaviour improvement of a low Cr–Mo prealloyed powder steel through Mn additions and others liquid phase promoters’, J. Mater. Process. Technol., 2003, 143–144, 464–469. doi: 10.1016/S0924-0136(03)00459-X
36.
BidulskýR., BidulskáJ. and Actis GrandeM.: ‘Response of the Cr-alloyed PM steels on vacuum sintering and heat treatment’, High Temp. Mater. Processes, 2013, 32, 467–473. doi: 10.1515/htmp-2012-0174
37.
CiasA.: ‘Chemical reactions during sintering of Fe–Cr–Mn–Si–Ni–Mo–C steels with special reference to processing in semi-closed containers’, Sci. Sinter., 2015, 47, 61–69. doi: 10.2298/SOS1501061C
