Recent concern over the harmful effects on the ecology of long lasting plastics has led to heightened interest in the development of more environmentally sustainable materials. Attention has been paid to biodegradable thermoplastic polymers, polylactic acid (PLA) and polybutylene succinate (PBS). However, although these materials have been widely used as matrix in a composite, the potential of biopolymers as reinforcement in a composite structural system has been examined less. Two types of unidirectional biodegradable composites, PLA self-reinforced and PLA reinforced PBS matrix composites, were produced. The composites were tested for Young's modulus, tensile strength and strain at break. Cross-section and fracture surface characteristics of the composites were also examined by scanning electron microscopy to identify damage modes. It is found that the tensile strength of both PLA self-reinforced and PLA–PBS composites is increased by 10–40%, while their initial modulus is 2–6 times higher than that measured for PLA and PBS films.
BalkcomMB, WeltB and BergerK: ‘Notes from the packaging laboratory: PLA – an exciting new packaging material’, ABE339, The University of Florida, Gainesville, FL, USA, 2002.
5.
AurasR, HarteB and SelkeS: ‘An overview of polylactides as packaging materials’, Macromol. Biosci., 2004, 4, (9), 835–864.
6.
LiuL, YuJ, ChengL and QuW: ‘Mechanical properties of poly(butylene succinate) (PBS) biocomposites reinforced with surface modified jute fibre’, Composites Part A, 2009, 40A, 669–674.
7.
LiuL, YuJ, ChengL and YangX: ‘Biodegradability of poly(butylene succinate) (PBS) composite reinforced with jute fibre’, Polym. Degrad. Stab., 2009, 94, 90–94.
8.
BhatiaA, GuptaRK, BhattacharyaSN and CholHJ: ‘Compatibility of biodegradable poly (lactic acid) (PLA) and poly (butylene succinate) (PBS) blends for packaging application’, Korea–Aust. Rheol. J., 2007, 19, (3), 125–131.
9.
LeeSM, ChoD, ParkWH, LeeSG, HanSO and DrzalLT: ‘Novel silk/poly(butylene succinate) biocomposites: the effect of short fibre content on their mechanical and thermal properties’, Compos. Sci. Technol., 2005, 65, 647–657.
10.
HanY.-K, KimS.-R and KimJ: ‘Preparation and characterization of high molecular weight poly(butylene succinate)’, Macromol. Res., 2002, 10, (2), 108–114.
11.
YooES and ImSS: ‘Melting behavior of poly(butylene succinate) during heating scan by DSC’, J. Polym. Sci. B, 1999, 37B, 1357–1366.
12.
YasuniwaM and SatouT: ‘Multiple melting behaviour of poly(butylene succinate) 1. Thermal analysis of melt-crystallized samples’, J. Polym. Sci. B, 2002, 40B, 2411–2420.
13.
OksmanK, SkrifvarsM and SelinJ.-F: ‘Natural fibres as reinforcement in polylactic acid (PLA) composites’, Compos. Sci. Technol., 2003, 63, 1317–1324.
14.
PlackettD, AndersenTL, PedersenWB and NielsenL: ‘Biodegradable composites based on L-polylactide and jute fibres’, Compos. Sci. Technol., 2003, 63, 1287–1296.
15.
KhondkerOA, IshiakuUS, NakaiA and HamadaH: ‘A novel processing technique for thermoplastic manufacturing of unidirectional composites reinforced with jute yarns’, Composites Part A, 2006, 37A, 2274–2284.
16.
SawpanMA, PickeringKL and FernyhoughA: ‘Improvement of mechanical performance of industrial hemp fibre reinforced polylactide biocomposites’, Composites Part A, 2011, 42A, (3), 310–319.
17.
SawpanM, PickeringK and FernyhoughA: ‘Characterisation of hemp fibre reinforced poly (lactic acid) composites’, Adv. Mater. Res., 2007, 29, 337–340.
18.
SerizawaS, InoueK and IjiM: ‘Kenaf-fiber-reinforced poly (lactic acid) used for electronic products’, J. Appl. Polym. Sci., 2006, 100, (1), 618–624.
19.
BenG, KiharaY, NakamoriK and AokiY: ‘Examination of heat resistant tensile properties and molding conditions of green composites composed of kenaf fibers and PLA resin’, Adv. Compos. Mater., 2007, 16, (4), 361–376.
20.
HudaMS: ‘Effect of fiber surface-treatments on the properties of laminated biocomposites from poly (lactic acid) (PLA) and kenaf fibers’, Compos. Sci. Technol., 2008, 68, (2), 424–432.
21.
GarcíaM, GarmendiaI and GarciaJ: ‘Influence of natural fiber type in eco-composites’, J. Appl. Polym. Sci., 2008, 107, (5), 2994–3004.
22.
HuR and LimJK: ‘Fabrication and mechanical properties of completely biodegradable hemp fiber reinforced polylactic acid composites’, J. Compos. Mater., 2007, 41, (13), 1655–1669.
23.
LeeSH and WangS: ‘Biodegradable polymers/bamboo fiber biocomposite with bio-based coupling agent’, Composites Part A, 2006, 37A, (1), 80–91.
24.
CapiatiNJ and PorterRS: ‘The concept of one polymer composites modelled with high density polyethylene’, J. Mater. Sci., 1975, 10, 1671–1677.
25.
PeijsT: ‘Composites for reconcilability’, Mater. Today, Apr. 2003, 30–35.
26.
ZhangJM and PeijsT: ‘Self-reinforced poly (ethylene terephthalate) composites by hot consolidation of bi-component PET yarns’, Composites Part A, 2010. 41A, 964–972.
27.
HeT and PorterRS: ‘Melt transcrystallization of polyethylene on high modulus polyethylene fibres’, J. Appl. Polym. Sci., 1988, 35, 1945–1953.
28.
MaraisC and FeillardP: ‘Manufacturing and mechanical characterization of unidirectional polyethylene–fibre/polyethylene–matrix composites’, Compos. Sci. Technol., 1992, 45, 247–255.
29.
TeishevA, IncardonaS, MigliaresiC and MaromG: ‘Polyethylene fibres–polyethylene matrix composites: preparation and physical properties’, J. Appl. Polym. Sci., 1993, 50, 503–512.
30.
HoushyarS and ShanksRA: ‘Morphology, thermal and mechanical properties of poly (propylene) fibre–matrix composites’, Macromol. Mater. Eng., 2003, 288, 599–606.
31.
AlcockB, CabreraNO, BarkoulaNM, LoosJ and PeijsT: ‘The mechanical properties of unidirectional all-polypropylene composites’, Composites Part A, 2006, 37A, 716–726.
32.
BaranyT, IzerA and CziganyT: ‘On consolidation of self-reinforced polypropylene composites’, Plast. Rubber Compos., 2006, 35, (9), 375–379.
33.
BaranyT, Karger-KocsisJ and CziganyT: ‘Development and characterization of self-reinforced poly (propylene) composites: carded mat reinforcement’, Polym. Adv. Technol., 2006, 17, 818–824.
34.
LoosJ, SchimanskiT, HofmanJ, PeijsT and LemstraPJ: ‘Morphological investigations of polypropylene single-fibre reinforced polypropylene model composites’, Polymer, 2001, 42, 3827–3834.
35.
CabreraNO, AlcockB, KlompenETJ and PeijsT: ‘Filament winding of co-extruded polypropylene tapes for fully recyclable all-polypropylene composite products’, Appl. Compos. Mater., 2008, 15, 27–45.
36.
ZhangJM, ReynoldsCT and PeijsT: ‘All-poly(ethylene terephthalate) composites by film stacking of oriented tapes’, Composites Part A, 2009, 40A, 1747–1755.
37.
HullD and ClyneTW: ‘An introduction to composite materials’, 2nd edn, Cambridge solid state science series; 1996, New York, Cambridge University Press.
38.
CookJ, EvansCC, GordonJE and MarshDM: ‘A mechanism for the control of crack propagation in all-brittle systems’, Proc. R. Soc. Lond. A, 1964, 282A, (1391), 508–520.
39.
CallisterWD: ‘Materials science and engineering: an introduction’; 2007, New York, John Wiley & Sons.
40.
ChengS, LauK, LiuT, ZhaoY, LamPM and YinY: ‘Mechanical and thermal properties of chicken feather fiber/PLA green composites’, Composites Part B, 2009, 40B, (7), 650–654.
