Deep Mining 2012 is the sixth in a series of international seminars on deep and high stress mining which began with a seminar held in Perth in November 2002, almost a decade ago. The early announcements for this seminar listed 10 seminar themes. This paper seeks to make contributions to the discussion of progress made in four of these themes – geomechanics risks, risk assessment and management, rock behaviour under high stress, and numerical modelling – largely, but not only, through a review of the papers published in the proceedings of the five previous seminars. Particular emphasis is placed on the risks associated with the new generation of block and panel caving operations or ‘super caves’. Some remaining challenges in the four theme areas discussed are also identified.
AndrieuxP, HadjigeorgiouJ, Sampson-ForsytheA, SimserB, TurichshevA, BrummerR.2010. Recent case histories of the application of the empirical destressability index methodology, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 17–27.
2.
ArancibiaE, CarrascoF, FuentesS, GuardaJ.2008. Design of extraction layout for the Chuquicamata underground project, Proc. 5th Int. Conf. on ‘Mass mining’, (ed. , SchunnessonH, NordlundE), June 2008, Luleå, Sweden, Luleå University of Technology Press, 3–14.
3.
BaecherGB, ChristianJT. 2003. Reliability and statistics in geotechnical engineering, New York, John Wiley.
4.
BahraniN, ValleyB, KaiserPK, PierceM.2011. Evaluation of PFC2D grain-based model for simulation of confinement-dependent rock strength degradation and failure processes, Proc. 45th US Rock Mechanics/Geomechanics Symp., June 2011, San Francisco, CA, USA, Paper ARMA11-156 (CD-ROM).
5.
BarrettD, PlayerJ.2002. Big Bell, high stress at shallow depth, Proc. 1st Int. Semin. on ‘Deep and high stress mining’, November 2002, Perth, Australia, Australian Centre for Geomechanics, Section 28.
6.
BeckD, SandyM.2002. Mine sequencing for high recovery in Western Australian mines, Proc. 1st Int. Semin. on ‘Deep and high stress mining’, November 2002, Perth, Australia, Australian Centre for Geomechanics, Section 8.
7.
BeckD, ArndtS, ThinI, StoneC, ButcherR.2006a. A conceptual sequence for a block cave in an extreme stress and deformation environment, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 11. Also in 2007. Challenges in deep and high stress mining, (ed. Y. Potvin et al.), 65–76, Perth, Australian Centre for Geomechanics.
8.
BeckD, ReuschF, ArndtS.2007. Estimating the probability of mining-induced seismic events using mine-scale, inelastic numerical models, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 31–41.
9.
BeckD, ReuschF, ArndtS, ThinI, StoneC, HeapM, TylerD.2006b. Numerical modelling of seismogenic development during cave initiation, propagation and breakthrough, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 12. Also in 2007. Challenges in deep and high stress mining, (ed. Y. Potvin et al.), 275–281, Perth, Australian Centre for Geomechanics.
10.
BeckDA, FilleryB, ReuschF.2010. 3D hydro-mechanical simulation of faulted open pit slopes, Proc. 44th US Rock Mechanics Symp. and 5th US–Canada Rock Mechanics Symp., June 2010, Salt Lake City UT, USA, Paper ARMA 10-425 (CD-ROM).
11.
BeckDA, PfitznerMJ, ArndtSM, FilleryB.2009. Estimating rock mass properties and seismic response using higher order, discontinuous, finite element models, Rock engineering in difficult conditions (Proc. 3rd Canada–US Rock Mechanics Symp. and 20th Canadian Rock Mechanics Symp.), (ed. , DiederichsM, GrasselliG), May 2009, Toronto (CD-ROM).
12.
BeenK, BrownET, HepworthN.2002. Liquefaction potential of paste fill at Neves Corvo mine, Portugal, Trans. IMM A, 111A, 47–58.
13.
BeerG, WatsonJO. 1992. Introduction to finite and boundary element methods for engineers, Chichester, John Wiley.
14.
BoardM, DamjanacB, PierceM.2007. Development of a methodology for analysis of instability in room and pillar mines, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 273–282.
15.
BradyBHG. 1979. A direct formulation of the boundary element method of stress analysis for complete plane strain, Int. J. Rock Mech. Min. Sci., 16, (4), 235–244.
16.
BradyBHG. 1987. Boundary element and linked methods for underground excavation design, Analytical and computational methods in engineering rock mechanics, (ed. , BrownE T, ed), 164–204, London, Allen and Unwin.
17.
BradyBHG, BrownET. 2004. Rock mechanics for underground mining, 3rd edn, Dordrecht, Kluwer.
18.
BrownET. 1974. Fracture of rock under uniform biaxial compression, Proc. 3rd Cong. on ‘Advances in rock mechanics’, September 1974, Denver, CO, USA, National Academy of Sciences, Vol. 2A, 111–117.
19.
BrownET1999The evolution of support and reinforcement philosophy and practice for underground mining excavationsProc. Int. Symp. on ‘Ground support’(, VillaescusaE, ), March 1999, Kalgoorlie, Australia, Balkema, 3–17.
BrownET2007bRock mechanics – the basic mining science: challenges in underground mass miningProc. 11th Cong. ISRM Cong. on ‘Rock mechanics’(, SousaL Ribeiro e, ), July 2007, Lisbon, Portugal, Taylor and Francis, Vol. 3, 1335–1347.
22.
BrownET2008Estimating the mechanical properties of rock massesProc. 1st SHIRMS(, PotvinY, ), Vol. 1, Mining and civil, September 2009, Perth, Australia, Australian Centre for Geomechanics, 3–22.
23.
BrownET. 2011. Fifty years of the ISRM and associated progress in rock mechanics, Proc. 12th ISRM Cong. on ‘Rock mechanics’, (ed. , QianQ, ZhouY X), October 2011, Beijing, China, CRC Press/Balkema, 29–45.
24.
BrownET, BoothA.2009. Risk management, Guidelines for open pit slope design, (ed. , ReadJ, StaceyP), 381–400, Melbourne, CSIRO Publishing.
25.
BrummerRK, NoséJP, HayL, KaiserPK. 1993. Risk-cost-benefit analysis applied to the design of support in burst-prone mines, Proc. Int. Cong. on ‘Mine design’, (ed. , BawdenW F, ArchibaldJ F), August 1993, Kingston, Canada, Balkema, 969–980.
26.
CalderónAR, TapiaAD2006Slope-steepening decision using quantified risk assessment: the Chuquicamata case50 years of rock mechanics – landmarks and future challenges (Proc. 41st US Rock Mechanics Symp.)(, YaleD, ), 17–21 June, Golden, U.S.A., Paper 06–1145, 8 p. (CD-ROM).
27.
ChitomboGP. 2010. Cave mining – 16 years after Laubscher's 1994 paper ‘Cave mining – state of the art’, Proc. 2nd Int. Symp. on ‘Block and sublevel caving’, (ed. , PotvinY, ed), April 2010, Perth, Australia, Australian Centre for Geomechanics, 45–61.
28.
CockramMJ, MakinenEO, KirstenHAD. 2004. A methodology to quantify risk and an application to remnant mining, Proc. 2nd Int. Semin. on ‘Deep and high stress mining’, February 2004, Johannesburg, South Africa, SAIMM, 147–158.
29.
CookNGW, HoekE, PretoriusJPG, OrtleppWD, SalamonMDG. 1966. Rock mechanics applied to the study of rockbursts, J. SAIMM, 16, (10), 436–528.
30.
CorthésyR, LeiteMH. 2008. A strain-softening numerical model of core discing and damage, Int. J. Rock Mech. Min. Sci., 45, (3), 329–350.
31.
CretuO, StewartR, BerendsT.2011. Risk management for design and construction, Hoboken, NJ, John Wiley.
32.
CrouchSL, StarfieldAM. 1983. Boundary element methods in solid mechanics, London, Allen and Unwin.
33.
CundallPA. 1971. A computer model for simulating progressive, large-scale movements in blocky rock systems, Proc. Int. Symp. on ‘Rock mechanics’, October 1971, Nancy, France, ISRM, Vol. 1, Paper II-8.
34.
CundallPA. 1987. Distinct element models of rock and soil structure, Analytical and computational methods in engineering rock mechanics, (ed. , BrownE T, ed), 129–163, London, Allen and Unwin.
35.
CundallPA2011Lattice method for modelling brittle, jointed rock, Continuum and distinct element numerical modeling in geomechanics – 2011(Proc. 2nd International FLAC/DEM Symp.)(, SainsburyD P, ), February 2011, Melbourne, Australia, Itasca International Inc., 11–19.
36.
CundallPA, DamjanacB.2009. A comprehensive 3D model for rock slopes based on micromechanics, Proc. 3rd Int. Symp. on ‘Rock slope stability’, November 2009, Santiago, Chile, ISRM (CD-ROM).
37.
DetournayE.1995. Coupled thermo-hydro-mechanical processes in rock mechanics, with applications to the petroleum industry, Proc. 8th ISRM Cong. on ‘Rock mechanics, (ed. , FujiT, ed), September 1995, Tokyo, Japan, Balkema, Vol. 3, 1061–1068.
38.
DiederichsMS, KaiserPK. 1996. Rock instability and risk analyses in open stope mine design, Can.Geotechn. J., 33, (3), 431–439.
39.
DiederichsMS, KaiserPK, EberhardtE.2004. Damage initiation and propagation in hard rock during tunnelling and the influence of near-face stress rotation, Int. J. Rock Mech. Min. Sci., 41, (5), 785–812.
40.
DightPM, DyskinAV. 2007. Accounting for the effect of rock mass anisotropy in stress measurements, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 415–424.
41.
DunnMJ. 2004. Initial risk assessment of rock passes in AngloGold's SA region, Proc. 2nd Int. Semin. on ‘Deep and high stress mining’, February 2004, Johannesburg, SAIMM, 413–421.
42.
DuplancicP, BradyBH. 1999. Characterisation of caving mechanisms by analysis of seismicity and rock stress, Proc. 9th ISRM Cong., (ed. , VouilleG, BerestP), August 1999, Paris, France, Balkema, Vol. 2, 1049–1053.
43.
DurrheimRJ, CichowiczA, Ebrahim-TrollopeR, EssrichF, GoldbachO, LinzerLM, SpottiswoodeSM, StankiewiczT.2007. Guidelines, standards and best practice for seismic hazard assessment and rockburst risk management in South African mines, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 249–261.
44.
EberhardtE, SteadD, StimpsonB.1999. Effects of sample disturbance on the stress-induced microfracturing characteristics of brittle rock, Can. Geotechn. J., 36, (2), 239–250.
45.
EinsteinHH, BaecherGB. 1983. Probabilistic and statistical methods in engineering geology, Part I Exploration, Rock Mech. Rock Eng., 16, (1), 39–72.
46.
ElsworthD.1986. A hybrid boundary element-finite element analysis procedure for fluid flow simulation in fractured rock masses, Int. J. Numer. Anal. Methods Geomech., 10, (6), 569–584.
47.
FairhurstC2011Grand challenges in earth resources engineering – and some implications for rock mechanics and rock engineeringContinuum and distinct element numerical modelling in geomechanics – 2011 (Proc. 2nd Int. FLAC/DEM Symp.)(, SainsburyD P, ), February 2011, Melbourne, Australia, Itasca International Inc., 3–10.
48.
FalmagneV, FrenetteP.2006. Ground control challenges at Mine Doyen – a case history, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 3.
49.
GerogiannopoulosNG. 1976. A critical state approach to rock mechanics, PhD thesis, University of London, London, UK.
50.
GiodaG, SakuraiS.1987. Back analysis procedures for the interpretation of field measurements in geomechanics, Int. J. Numer. Anal. Methods Geomech., 11, (6), 555–583.
51.
GlazerSN, TownsendPA. 2010. Relationship between production rates, the caving process and seismicity rates at Palabora Mining Company, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 491–502.
52.
GoodmanRE, ShiG-H. 1985. Block theory and its application to rock engineering, Englewood Cliffs, Prentice-Hall.
53.
GoodmanRE, TaylorRL, BrekkeTL. 1968. A model for the mechanics of jointed rock, J. Soil Mech. Foundat. Div., 94, (SM3), 637–659.
54.
GuilfoyleK, SladeN, KenworthyS.2006. The N3500 project – deep, high stress and talc, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeourgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 13.
55.
GumedeH, StaceyTR. 2007. Measurement of typical joint characteristics in South African gold mines and the use of these characteristics in the prediction of rock falls, J. SAIMM, 107, (5), 335–344.
56.
HadjigeorgiouJ, HarrisonJP. 2011. Uncertainty and sources of error in rock engineering, Harmonising rock engineering and the environment (Proc. 12th ISRM Cong.), (ed. , QianQ, ZhouY X), October, Beijing, China, CRC Press/Balkema, 2063–2067.
57.
HammahRE, CarvalhoJL. 2011. An introduction to the Christensen criterion – an answer to true, representative modelling of intact rock yielding/failure? Proc. Int. Symp. on ‘Rock slope stability in open pit mining and civil engineering’, September 2011, Vancouver, BC, Canada, University of British Columbia (CD-ROM).
58.
HarrME. 1987. Reliability based design in civil engineering, New York, McGraw-Hill.
59.
HarrisonJP, HudsonJA. 2003. Visualising and understanding the stress path for rock mechanics modelling and testing, and rock engineering design, Technology roadmap for rock mechanics(Proc. 10th ISRM Cong.), September 2003, Johannesburg, South Africa, SAIMM, Vol. 1, 487–492.
60.
HartRD, DetournayCL, CundallPA. (eds.) 2008. Continuum and distinct element modeling in geo-engineering, Proc. 1st FLAC/DEM Symp., August 2008, Minneapolis, MN, USA, Itasca Consulting Group Inc.
61.
HebblewhiteBK. 2003. Management of geotechnical risks in mining projects, Proc. Mining Risk Management Conf: Effective risk management for mining project optimisation, September 2003, Sydney, Australia, AusIMM.
62.
HebblewhiteBK. 2009. Mine safety – through appropriate combination of technology and management practice, Procedia Earth Planet. Sci., 1, (1), 13–19.
63.
HillFG. 1954. An investigation of the problem of rockbursts; an operational research project, Part I, The approach to the problem and analyses of the rockbursts that have occurred on the ERPM during the years 1948–1953, J. Chem. Metall. Min. Soc. South Afr., 55, 63–83.
64.
HillFG. 1966. Preface to ‘Rock mechanics applied to the study of rockbursts’, J. SAIMM, 66, (10),435.
65.
HoekE.1991. When is a design in rock engineering acceptable?Proc. 7th ISRM Cong., (ed. , WittkeW, ed), September 1991, Aachen, Germany, Balkema, Vol. 3, 1485–1497.
66.
HoekE, BrownET. 1980. Underground excavations in rock, London, IMM.
67.
HoodM, HatherlyP, GurgenciH.1999. Mining in 2015, Min. Mag. Min. Commun., 181, (4), 222–229.
68.
HorsleyTP, MedhurstTP. 2000. Quantifying geotechnical risk in the mine planning process, Proc. MassMin 2000, (ed. , ChitomboG, ed), October–November 2000, Brisbane, Australia, Australasian Institute of Mining and Metallurgy, 105–112.
69.
HudsonJA, StephanssonO, AnderssonJ, TsangC-F, JingL.2001. Coupled T-H-M issues relating to radioactive waste repository design and performance, Int. J. Rock Mech. Min. Sci., 38, (1), 143–161.
70.
HudymaM, PotvinY, HealD.2006. The mine seismicity risk analysis program (MS-RAP) – transforming microseismic data into rock engineering knowledge, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeourgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 29.
71.
Itasca. 2011. FLAC Ver 6.0, FLAC3D Ver 4.0, FLAC/Slope Ver 6.0, UDEC Ver 5.0 & 3DEC Ver 4.1, Itasca Consulting Group Inc., Minneapolis, MN, USA(see www.itascacg.com/home.php).
72.
JaegerJC, CookNGW, ZimmermanRW. 2007. Fundamentals of rock mechanics, 4th edn, Oxford, Blackwell.
73.
JingL.2003. A review of techniques, advances and outstanding issues in numerical modelling for rock mechanics and rock engineering, Int. J. Rock Mech. Min. Sci., 30, (3), 283–353.
74.
JingL, StephanssonO.2007. Fundamentals of discrete element methods for rock engineering: theory and applications, Amsterdam, Elsevier.
75.
JoughinWC, StaceyTR. 2005. Risks associated with rockpasses in deep-level tabular mines based on historical pass performance, J. SAIMM, 105, (1), 795–802.
76.
KaiserPK, KimB-H2008Rock mechanics challenges in underground construction and miningProc. 1st SHIRMS(, PotvinY, ), Vol. 1, Mining and civil, September 2009, Perth, Australia, Australian Centre for Geomechanics, 23–38.
77.
KaiserPK, KimB.-H, BewickRP, ValleyB.2010. Rock mass strength at depth and implications for pillar design, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 463–476.
78.
KibokoMK, HaganTO, VieiraFMCC, RangasamyT.2004. A review of shaft pillar extraction in the South African gold mines, Proc. 2nd Int. Semin. on ‘Deep and high stress mining’, February 2004, Johannesburg, South Africa, SAIMM, 423–437.
79.
KloppenburgA, GrocottJ, HutchinsonD.2010. Structural setting and synplutonic fault kinematics of a cordilleran Cu–Au–Mo mineralization system, Bingham Canyon Mining District, Utah, Econ. Geol., 105, (4), 743–761.
80.
LanaroF, SatoT, NakamaS.2009. Depth variability of compressive test results of Toki granite from Shobasama and Mizunami construction sites, Japan, Rock Mech. Rock Eng., 42, (4), 611–629.
81.
LiT, SinghU, CoxonJ.2002. A case study of management of high stress and seismicity at Junction Mine, Proc. 1st Int. Semin. on ‘Deep and high stress mining‘,November 2002, Perth, Australia, Australian Centre for Geomechanics, Section 29.
82.
LoganA, TylerD.2004. Air inrush risk assessment for caving mines, Proc. MassMin 2004, (ed. , KarzulovicA, AlvaroM), August 2004, Santiago, Chile, Instituto de Ingenieros de Chile, 717–721.
83.
LorigLJ, BradyBHG. 1982. A hybrid discrete element-boundary element method of stress analysis, Issues in rock mechanics(Proc. 3rd US Symp. on ‘Rock mechanics’), (ed. , GoodmanR E, HeuzéF E), August, Berkeley, USA, AIME, 628–636.
84.
MaGW. 2011. Discontinuous deformation analysis: advances and challenges, Harmonising rock engineering and the environment, (Proc. 12th ISRM Cong.), (ed. , QianQ, ZhouY X), October 2011, Beijing, China, CRC Press/Balkema, 99–108.
85.
MancaP, DunstanG.2008. Planning the transition from SLC to block caving operations at Ridgeway gold mine, Proc. 5th Int. Conf. on ‘Mass mining’, (ed. , SchunnessonH, NordlundE), June 2008, Luleå, Sweden, Luleå University of Technology Press, 401–412.
86.
MarshallK.2011. The future is underground, Mater. World,19, (8), 34–35.
87.
MartinCD, ChristianssonR.2009. Estimating the potential for spalling around a deep nuclear waste repository in crystalline rock, Int. J. Rock Mech. Min. Sci., 46, (2), 219–228.
88.
MartinCD, StimpsonB.1994. The effect of sample disturbance on laboratory properties of Lac du Bonnet granite, Can. Geotechn. J., 31, (5), 692–702.
89.
MatsukiK, KagaN, YokoyamaT, TsudaN.2004. Determination of three dimensional in situ stress from core discing based on analysis of principal tensile stress, Int. J. Rock Mech. Min. Sci., 41, (7), 1167–1190.
90.
MaybeeG, Sampson-ForsytheA, CotestaL, O'ConnorC.2006. Geomechanical challenges at Xstrata Nickel's Thayer Lindsley Mine, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 2.
91.
McCarthyP.2002. Feasibility studies and economic models for deep mines, Proc. 1st Int. Semin. on ‘Deep and high stress mining’, November 2002, Perth, Australia, Australian Centre for Geomechanics, Section 4.
92.
McCrackenA, StaceyTR. 1989. Geotechnical risk assessment for large-diameter raise-bored shafts, Proc. Conf. on ‘Shaft engineering’, June 1989, Harrogate, UK, IMM, 309–316. AlsoTrans. IMM A, 98A, 145–150.
93.
McGillRB. 2004. Strategies to manage seismicity in a deep VCR environment on Mponeng, Proc. 2nd Int. Semin. on ‘Deep and high stress mining’, February 2004, Johannesburg, South Africa, SAIMM, 79–94.
94.
McMahonBK. 1975. Probability of failure and expected volume of failure in high rock slopes, Proc. 2nd Australia–New Zealand Conf. on ‘Geomechanics’, July 1975, Brisbane, Australia, Institution of Engineers Australia, 308–313.
95.
Mercier-LangevinF.2010. LaRonde extension – mine design at three kilometres, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 3–15.
96.
Mercier-LangevinF, HadjigeorgiouJ.2010. Towards a better understanding of squeezing potential in hard rock mines, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 143–154.
97.
Mercier-LangevinF, TurcotteP.2006. Expansion at depth of Agnico-Eagle's La Ronde Division – meeting geotechnical challenges without compromising production objectives, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 1.
98.
MikulaPA, LeeMF. 2002. Forecasting and controlling pillar instability at Mt Charlotte Mine, Proc. 1st Int. Semin. on ‘Deep and high stress mining’, November 2002, Perth, Australia, Australian Centre for Geomechanics, Section 24.
99.
MogiK.2007. Experimental rock mechanics, Leiden, Taylor and Francis/Balkema.
100.
MorrisonD, BlakeW, HedleyD.2002. 100 years of rockbursting in North American hard rock mines, Proc. 1st Int. Semin. on ‘Deep and high stress mining’, November 2002, Perth, Australia, Australian Centre for Geomechanics, Section 2.
101.
MossA, RussellF, JonesC.2004. Caving and fragmentation at Palabora: prediction to production, Proc. MassMin 2004, (ed. , KarzulovicA, AlvaroM), August 2004, Santiago, Chile, Instituto de Ingenieros de Chile, 585–590.
102.
O'ConnorC, CotestaL, BrummerR, ThibodeauD.2010. Non-linear modelling calibration process for Vale nickel mines Ontario division, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 521–535.
103.
OrregoC, CuelloD, RojasE.2010. Determination of induced stress condition inside Pilar Norte sector, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 155–168.
104.
PascoeC, OddieM, EdgarI.2008. Panel caving at the Resolution copper project, Proc. MassMin 2008, (ed. , SchunnessonH, NordlundE), June 2008, Luleå, Sweden, Luleå University of Technology Press, 35–42.
PineRJ. 1992. Risk analysis design in mining geomechanics, Trans. IMM A, 101A, 149–158.
107.
PineRJ, CogganJS, FlynnZN, ElmoD.2006. The development of a new numerical modelling approach for naturally fractured rock masses, Rock Mech. Rock Eng., 39, (5), 395–419.
108.
PlewmanRP, DiestFH, OrtleppWD. 1969. The development and application of a digital computer method for the solution of strata control problems, J. SAIMM, 70, (2), 33–44.
109.
PotvinY, SladeN.2006. Controlling extreme ground deformation: learning from four Australian case studies, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 33.
110.
PotyondyDO, CundallP A.2004. A bonded-particle model for rock, Int. J. Rock Mech. Min. Sci., 41, (8), 1329–1364.
111.
PretoriusMJ. 2006. Quantification and management of risk in a deep mining environment, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 26.
112.
PriestSD, BrownET. 1983. Probabilistic stability analysis of variable rock slopes, Trans. IMM A, 92A, 1–12.
113.
ReuschF, BeckD.2007. Simulating shaft and crusher damage in deep mines, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 65–79.
114.
RogersS, ElmoD, WebbG, CatalanA.2010. A discrete fracture network based approach to defining in situ, primary and secondary fragmentation distributions for the Cadia East panel cave project, Proc. 2nd Int. Symp. on ‘Block and sublevel caving’, (ed. , PotvinY, ed), April 2010, Perth, Australia, Australian Centre for Geomechanics, 425–439.
115.
RyderJA, JagerAJ. (eds.) 2002. Rock mechanics for tabular hard rock mines, Johannesburg, SIMRAC.
116.
SainsburyDP, HartRD, DetournayCL, NelsonMJ. (eds.) 2011. Continuum and distinct element numerical modeling in geomechanics – 2011(Proc. 2nd Int. FLAC/DEM Symp.), February 2011, Melbourne, Australia, Itasca International Inc.
117.
SakuraiS1993Back analysis in rock engineering, Comprehensive rock engineering(, HudsonJ A, ), 543–569, Oxford, Pergamon Press.
118.
SalamonMDG. 1963. Elastic analysis of displacements and stresses induced by the mining of seam or reef deposits Part I: Fundamental principles and basic solutions as derived from idealized models, J. SAIMM, 64, (4), 128–149.
119.
SalamonMDG. 1964. Elastic analysis of displacements and stresses induced by the mining of seam or reef deposits. Part II: Displacement, strain and stress, J. SAIMM, 64, (6), 197–218.
120.
SalamonMDG. 1968. Two-dimensional treatment of problems arising from mining tabular deposits in isotropic or transversely isotropic ground, Int. J. Rock Mech. Min. Sci., 5, (2), 159–185.
121.
SalamonMDG, RyderJA, OrtleppWD. 1964. An analogue solution for determining the elastic response of strata surrounding tabular mine excavations, J. SAIMM, 65, (2), 115–137.
122.
SharrockG, SladeN, ThinI, DuplancicP.2002. The prediction of stress induced caving on a mining abutment, Proc. 1st Int. Semin. on ‘Deep and high stress mining’, November 2002, Perth, Australia, Australian Centre for Geomechanics, Section 13.
123.
ShiG-H, GoodmanRE. 1985. Two dimensional discontinuous deformation analysis, Int. J. Numer. Anal. Methods Geomech., 9, (6), 541–556.
124.
SimserBP. 2006. Strategic and tactical approaches for mining at depth at Xstrata's Craig Mine, Proc. Third Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 6.
125.
SimserBP. 2007. The weakest link – ground support observations at some Canadian Shield hard rock mines, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 335–348.
126.
SinghU, DixonRA, McArthurC.2010. Interaction between a propagating cave and an active pit at Telfer Mine – Part I: interaction management, Proc. 2nd Int. Symp. on ‘Block and sublevel caving’, (ed. , PotvinY, ed), April 2010, Perth, Australia, Australian Centre for Geomechanics, 307–320.
127.
SpottiswoodeS.2004. A seismic and modelling analysis of dip-pillar mining, Proc. Second Int. Semin. on ‘Deep and high stress mining’, 23–25 February, Johannesburg, South Africa, SAIMM, 67–78.
128.
StaceyTR, GumedeH.2007. Evaluation of risk of rock fall accidents in gold mine stopes based on measured joint data, J. SAIMM, 107, (5), 345–350.
129.
StaceyTR, TerbruggePJ, WesselooJ.2006. Risk as a rock engineering design criterion, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 27. Also in Challenges in deep and high stress mining, (ed. Y. Potvin et al.), 19–25, Perth, Australian Centre for Geomechanics.
Standards Australia. 2009. AS/NZS ISO 31000:2009 Risk management principles and guidelines, Standards Australia, Sydney, Australia.
132.
StarfieldAM, CundallPA. 1988. Towards a methodology for rock mechanics modelling, Int. J. Rock Mech. Min. Sci., 25, (3), 99–106.
133.
SteffenOKH. 1997. Planning open pit mines on a risk basis, J. SAIMM, 97, (2), 47–56.
134.
SteffenOKH, ContrerasLF, TerbruggePJ, VenterJ.2008. A risk evaluation approach for pit slope design, Proc. 42nd US Rock Mechanics Symp. and 2nd US–Canada Rock Mechanics Symp., June–July, San Francisco, CA, USA, Paper ARMA 08-231 (CD-ROM).
135.
SteffenOKH, TerbruggePJ, WesselooJ, VenterJ.2006. A risk consequence approach to open pit design, Proc. Int. Symp. on ‘Stability of rock slopes in open pit mining and civil engineering’, April, Cape Town, South Africa, SAIMM, 81–96.
SummersJ.2000. Analysis and management of mining risk, Proc. MassMin 2000, (ed. , ChitomboG, ed), October–November 2000, Brisbane, Australia, Australasian Institute of Mining and Metallurgy, 63–79.
138.
SuorineniFT, DusseaultMB, BrummerRK. 1995. Probabilistic risk and reliability evaluation of ground control practices in underground mining: the safety and economic implications, Proc. 35th US Symp. on ‘Rock mechanics’, (ed. , DaemanJ J K, SchultzR A), June, Reno, USA, Balkema, 579–584.
139.
SwanG, CarlisleS, MaybeeG, PritchardC, Sampson-ForsytheA, SimserB, CounterD.2006. Ground support systems for high stress conditions: theory vs experience, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 37.
140.
SweeneyD, ScobleM.2006. Back analysis of risk and boundary condition and decision analysis applied to deep mining, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 28.
141.
TapiaA, ContrerasLF, JeffriesM, SteffenO.2007. Risk evaluation of slope failure at the Chuquicamata Mine, Proc. Int. Symp. on ‘Rock slope stability in open pit mining and civil engineering’, (ed. , PotvinY, ed.), September 2007, Perth, WA, Australia, Australian Centre for Geomechanics, 477–495.
142.
TarasovBG. 2008a. Intersonic shear rupture mechanism, Int. J. Rock Mech. Min. Sci., 45, (6), 914–928.
143.
TarasovBG2008bNew insight into the nature of shear rupture propagation in pristine rocks and pre-existing faultsProc. 1st SHIRMS(, PotvinY, ), Vol. 2, Fundamental and petroleum, September 2009, Perth, Australia, Australian Centre for Geomechanics, 37–68.
144.
TarasovBG. 2010. Superbrittleness of rocks at high confining pressure, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 119–133.
145.
TarasovBG. 2011. Experimental evidences of dramatic embrittlement of hard rocks due to rising confining pressure at triaxial compression, Harmonising rock engineering and the environment (Proc. 12th ISRM Cong.), (ed. , QianQ, ZhouY X), October 2011, Beijing, China, CRC Press/Balkema, 845–849.
146.
TarasovBG, DyskinAV. 2005. The phenomenon of anomalous rock embrittlement, Controlling seismic risk (Proc. 6th Int. Symp. on ‘Rockburst and seismicity in mines’), (ed. , PotvinY, HudymaM), March 2005, Perth, Australia, ACG, 311–317.
147.
TarasovBG, OrtleppWD. 2007. Shock loading-unloading mechanism in rockburst shear fractures in quartzite causing genesis of polyhedral sub-particles in the fault gouge, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 183–192.
148.
TarasovBG, RandolphMF. 2007. Paradoxical features of primary shear fractures and general faults, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 165–182.
149.
TarasovBG, RandolphMF. 2008. Frictionless shear at great depth and other paradoxes of hard rocks, Int. J. Rock Mech. Min. Sci., 45, (3), 316–328.
150.
TarasovBG, RandolphMF. 2011. Superbrittleness of rocks and earthquake activity, Int. J. Rock Mech. Min. Sci., 48, (6), 888–898.
151.
TaylorJ.T.M.1962–63. Research on ground control and rockbursts on the Kolar Goldfield, India, Trans. IMM A, 72, 317–338
152.
TerbruggePJ, WesselooJ, VenterJ, SteffenOKH. 2006. A risk consequence approach to open pit slope design, J. SAIMM, 106, (7), 503–511.
153.
ThinI, WindsorC, VillaescusaE, StoneC.2006. Understanding the stress environment for the Perseverance Deeps Pre-feasibility Study, Proc. 3rd Int. Semin. on ‘Deep and high stress mining’, (ed. , HadjigeorgiouJ, GrenonM), October 2006, Quebec City, Que., Canada, Université Laval, Section 10.
154.
TylerDB, TruemanR, PineRJ. 1991. Rockbolt support design using a probabilistic method of key block analysis, in Rock Mechanics as a Multidisciplinary Science, Proc. 32nd US Rock Mechanics Symp., (ed. , RoegiersJ -C, ed), July 1991, Norman, OK, USA, Balkema, 1037–1047.
155.
ValleyB, BahraniN, KaiserP K2010aRock strength obtained from core samples and borehole wall instabilities – the effect of drilling induced damage, Rock mechanics in civil and environmental engineeringProc. European Rock Mechanics Symp. 2010(, ZhaoJ, ), June 2010, Lausanne, Switzerland, CRC Press/Balkema, 331–334.
156.
ValleyB, KaiserPK, DuffD.2010b. Consideration of uncertainty in modelling the behaviour of underground excavations, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 423–436.
157.
ValleyB, KimB-H, SourineniFT, BahraniN, BewickRP, KaiserPK. 2011. Influence of confinement dependent failure processes on rock mass strength at depth, Harmonising rock engineering and the environment, Proc. 12th ISRM Cong., (ed. , QianQ, ZhouY X), October 2011, Beijing, China, CRC Press/Balkema, 855–860.
158.
ValleyB, SuorineniFT, KaiserPK. 2010c. Numerical analyses of the effect of heterogeneities on rock failure process, Proc. 44th US Rock Mechanics Symp. and 5th US–Canada Rock Mechanics Symp., June 2010, Salt Lake City, UT, USA, Paper ARMA 10-468 (CD-ROM).
159.
VillaescusaE, LiJ, BairdG, SetoM.2002. Stress measurement from oriented core in Australia, Proc. 1st Int. Semin. on ‘Deep and high stress mining’, November 2002, Perth, Australia, Australian Centre for Geomechanics, Section 37.
160.
von KármánT.1911. Festigkeitsversuche unter allseitigem Druck, Zeitschrift Verein Deutscher Ingenieure, 55, 1749–1757.
161.
WatsonBP, KuijpersJS, HenryG, PalmerCE, RyderJA. 2009. Nonlinear rock behaviour and its implications for deeper level platinum mining, J. SAIMM, 108, (1), 5–13.
162.
WhitmanRV. 1984. Evaluating calculated risk in geotechnical engineering: 17th Terzaghi Lecture, J. Geotechn. Eng., 110, (2), 145–188.
163.
WilesTD. 2007. Evidence based model calibration for reliable predictions, Proc. 4th Int. Semin. on ‘Deep and high stress mining’, (ed. , PotvinY, ed), November 2007, Perth, Australia, Australian Centre for Geomechanics, 3–20.
164.
WindsorC, CavieresP, VillaescusaE, PerieraJ2006Reconciliation of strain, structure and stress in the El Teniente Mine region, Chile, In-situ rock stress: measurement, interpretation and applications(Proc. Int. Symp. on ‘In-situ rock stress’(, LuM, ), June 2006, Trondheim, Norway, Taylor and Francis, 244–260.
165.
WindsorCR. 2009. Rock stress measurements in upper Earth's crust, Proc. 2009 Australian Mining Technology Conf. on ‘Technology solutions for challenging financial times’, (ed. , KnightsP, LeverP), October 2009, Brisbane, Australia, AusIMM (CD-ROM).
166.
WittkeW.1977. Static analysis for underground openings in jointed rock, Numerical methods in geotechnical engineering, (ed. , DesaiC S, ChristianJ T), 589–638, New York, McGraw–Hill.
167.
WittkeW.1990. Rock mechanics: theory and applications with case histories, Berlin, Springer.
168.
YaoM, Moreau-VerlanL.2010. Strategies for mining in highly burst-prone ground conditions at Vale Garson Mine, Proc. 5th Int. Semin. on ‘Deep and high stress mining’, (ed. , van Sint JanM, PotvinY), October 2010, Santiago, Chile, Australian Centre for Geomechanics, 549–560.
169.
YunX, MitriHS, YangX.2011. Empirical failure criterion for biaxially loaded rock, Harmonising rock engineering and the environment, Proc. 12th ISRM Cong., (ed. , QianQ, ZhouY X), October, Beijing, China, CRC Press/Balkema, 909–914.
170.
YunX, MitriHS, YangX, WangY.2010. Experimental investigation into biaxial compressive strength of granite, Int. J. Rock Mech. Min. Sci., 47, (2), 334–341.
171.
ZienkiewiczOC. 1977. The finite element method, 3rd edn, London, McGraw–Hill.
