Based on the phase transformation theories, especially the T0 concept of bainite transformation, alloy optimisation of bainitic steel with carbides has been carried out aiming at the produce of plastic mould with large cross-section. The effect of manganese and silicon on proeutectoid ferrite and bainite transformation is explored by dilatometric analysis, XRD and different microscopy techniques. The results show that after the alloy optimisation, the transformation of proeutectoid ferrite is suppressed and when the cooling rate is lower than 0·1°C s− 1, the new lower bainite transformation appears by decreasing carbon capacity of austenite and promoting carbide precipitation. Industrial production proves that the optimised alloy SDP1 can meet the demand for the plastic mould with the thickness of 1050 mm.
GomezG., PérezT. and BhadeshiaH. K. D. H.: ‘Air cooled bainitic steels for strong, seamless pipes Part 1- alloy design, kinetics and microstructure’, Mater. Sci. Technol., 2009, 25, 1502–1507.
3.
BhadeshiaH. K. D. H.: ‘Nanostructure bainite’, Proc. R. Soc. A, 2010, 466, 3–18. doi: 10.1098/rspa.2009.0407
4.
HoseinyH., CaballeroF. G., MartinD. S. and CapdevillaC.: ‘The influence of austenitization temperature on the mechanical properties of a prehardened mould steel’, Mater. Sci. Forum, 2012, 706–709, 2140–2145. doi: 10.4028/www.scientific.net/MSF.706-709.2140
5.
FirraoD., MatteisP., ScavinoG., UbertalliG., GiuseppinaI. M., PinascoM. R., StagnoE., GerosaR., RivoltaB., SilvestriA., SilvaG. and GhidiniA.: ‘Relationships between tensile and fracture mechanics properties and fatigue properties of large plastic mold steel blocks’, Mater. Sci. Eng, 2007, A468–A470, 193–200. doi: 10.1016/j.msea.2006.07.166
6.
JiangL. and WangJ.: ‘Development of a non-quenched non-tempered bainitic steel for plastic mould: continuous cooling transformation behavior’, Proc. 5th Int. Conf. on ‘Tooling’, Leoben, Austria, Sepetmber 1999, University of Leoben, Paper 67, 685–690.
7.
LuoY., WuX. C., WangH. B. and MinY. A.: ‘A comparative study on non-quenched and quenched prehardened steel for large section plastic mold’, J. Mater. Process. Technol., 2009, 209, 5437–5442. doi: 10.1016/j.jmatprotec.2009.04.019
8.
HoseinyH., KlementU., SotskovszkiP. and AnderssonJ.: ‘Comparison of the microstructures in continuous-cooled and quench-tempered pre-hardened mould steels’, Mater. Des., 2011, 32, 21–28. doi: 10.1016/j.matdes.2010.06.045
9.
BhadeshiaH. K. D. H.: ‘Bainite in steels’, 2nd edn, 349; 2001, London, IoM Communications.
10.
SourmailT. and SmanioV.: ‘Optimisation of the mechanical properties of air cooled bainitic steel components through tailoring of the transformation kinetics’, Mater Sci. Eng. A, 2013, A582, 257–261. doi: 10.1016/j.msea.2013.06.040
11.
MatlockD. K., KraussG. and SpeerJ. G: ‘Microstructures and properties of direct-cooled microalloy forging steels’, J. Mater. Proc. Technol, 2001, 117, (3), 324–328. doi: 10.1016/S0924-0136(01)00792-0
12.
ZhangR. Y. and BoydJ. D.: ‘Bainite transformation in deformed austenite’, Metall. Mater. Trans. A., 2010, 41A, 1448–1459. doi: 10.1007/s11661-010-0190-x
13.
EnomotoM. and AaronsonH. I.: ‘Nucleation kinetics of proeutectoid ferrite at austenite grain boundaries in Fe-C-X alloys’, Met. Trans. A, 1986, 17, (8), 1385–1397. doi: 10.1007/BF02650120
14.
OiK., LuxC. and PurdyG. R.: ‘A study of the influence of Mn and Ni on the kinetics of the proeutectoid ferrite reaction in steels’, Acta Mater, 2000, 48, (9), 2147–2155. doi: 10.1016/S1359-6454(00)00041-0
15.
BhadeshiaH. K. D. H.: ‘Diffusional formation of ferrite in iron and its alloys’, Prog Mater. Sci., 1985, 29, (4), 321–386. doi: 10.1016/0079-6425(85)90004-0
16.
ZhuL. J., WuD. and ZhaoX. M.: ‘Effect of silicon content on thermodynamics of austenite decomposition in C-Si-Mn TRIP steels’, J. Iron Steel Res. Int, 2006, 13, (3), 57–60. doi: 10.1016/S1006-706X(06)60062-9
17.
CaballeroF. G., Garcia-MateoC. and MillerM. K.: ‘Modern steels at atomic and nanometer scales’, Mater. Sci. Technol., 2014, DOI: 10.1179/1743284714Y.0000000685.
18.
Hulme-SmithC. N., PeetM. J., LonardelliI., DippelA. C. and BhadeshiaH. K. D. H.: ‘Further evidence of tetragonality in bainitic ferrite’, Mater. Sci. Technol, 2015, 31, (2), 254–256. doi: 10.1179/1743284714Y.0000000691
19.
BhadeshiaH. K. D. H.: ‘Anomalies in carbon concentration determinations from nanostructured bainite’, Mater. Sci. Technol, 2014, DOI: 10.1179/1743284714Y.0000000655.
20.
BhadeshiaH. K. D. H. and EdmondsD. V.: ‘The mechanism of bainite formation in steels’, Acta Met, 1980, 28, 1265–1273. doi: 10.1016/0001-6160(80)90082-6
21.
SuzukiT., OnoY., MiyamotoG. and FuruharaT.: ‘Effects of Si and Cr on bainite microstructure of medium carbon steels’, ISIJ Int., 2010, 50, (10), 1476–1482. doi: 10.2355/isijinternational.50.1476
22.
JacquesP., GiraultE., CatlinT., GeerlofsN., KopT., van der ZwaagS. and DelannayF.: ‘Bainite transformation of low carbon Mn–Si TRIP-assisted multiphase steels: influence of silicon content on cementite precipitation and austenite retention’, Mater. Sci. Eng. A, 1999, 273–275, 475–479. doi: 10.1016/S0921-5093(99)00331-7
23.
CaballeroF. G. and BhadeshiaH. K. D. H.: ‘Very strong bainite’, Curr. Opin. Solid. State Mater. Sci., 2004, 8, (3–4), 251–257. doi: 10.1016/j.cossms.2004.09.005
24.
YangH. -S. and BhadeshiaH. K. D. H.: ‘Designing low carbon, low temperature bainite’, Mater. Sci. Technol., 2008, 24, (3), 335–342. doi: 10.1179/174328408X275982
25.
TakahashiM. and BhadeshiaH. K. D. H.: ‘A model for the microstructure of some advanced bainitic steels’, Mater. Trans, 1991, 32, 689–696. doi: 10.2320/matertrans1989.32.689
26.
KozeschnikE. and BhadeshiaH. K. D. H.: ‘Influence of silicon on cementite precipitation in steels’, Mater. Sci. Technol, 2008, 24, (3), 343–347. doi: 10.1179/174328408X275973
27.
Garcia-MateoC. and CaballoroF. G.: ‘Acceleration of low-temperature bainite’, ISIJ Int, 2003, 43, 1821–1825. doi: 10.2355/isijinternational.43.1821
28.
CaballeroF. G., BhadeshiaH. K. D. H., MawellaK. J. A., JonesD. G. and BrownP.: ‘Design of novel high strength bainitic steels: Part 1’, Mater. Sci. Technol, 2001, 17, 512–516. doi: 10.1179/026708301101510348
29.
MangononP. L.: ‘Effect of alloying elements on the microstructure and properties of a hot-rolled low-carbon low-alloy bainitic steel’, Metall. Trans. A, 1976, A7, 1389–1400. doi: 10.1007/BF02658825
30.
“Materials algorithms project (MAP)’, Department of Materials Science and Metallurgy, University of Cambridge, UK, available at: http://www.msm.cam.ac.uk/map (accessed 25 April 2014).
31.
GiraultE., JacquesP., HarletPh., MolsK., Van HumbeeckJ., AernoudtE. and DelannayF.: ‘Metallographic methods for revealing the multiphase microstructure of TRIP-assisted steels’, Mater. Charact, 1998, 40, 111–118. doi: 10.1016/S1044-5803(97)00154-X
32.
DysonD. J. and HolmesB.: ‘Effect of alloying additions on lattice parameter of austenite’, J. Iron Steel Inst, 1970, 208, 469–474.
33.
ŁawrynowiczZ.: ‘Transition from upper to lower bainite in Fe–C–Cr steel’, Mater. Sci. Technol., 2004, 20, 1447–1454. doi: 10.1179/026708304X3953
34.
GuptaC., DeyG. K., ChakravarttyJ. K., SrivastavD. and BanerjeeS.: ‘A study of bainite transformation in a new CrMoV steel under continuous cooling conditions’, Scr. Mater., 2005, 53, 559–564. doi: 10.1016/j.scriptamat.2005.04.031
35.
TakahashiM. and BhadeshiaH. K. D. H.: ‘Model for transition from upper to lower bainite’, Mater. Sci. Technol, 1990, 6, (7), 592–603. doi: 10.1179/mst.1990.6.7.592
