In this present work, the influence of constitutional undercooling on the grain size of titanium aluminide alloys and the dependence on boron content have been investigated. By means of the TTTIAL1 thermodynamic database of the Thermo-Calc programme, the values of the growth restriction factor for a series of alloys have been calculated. It can be shown that grain size decreases with increasing growth restriction factor. A comparison of calculated and published experimental results shows that the constitutional undercooling significantly influences the grain size in titanium aluminide alloys, but most likely, it is not the unique mechanism of grain refinement alone, in so far as not all of the experimental results may be explained by the influence of constitutional undercooling.
ImayevRM, ImayevVM, OehringM and AppelF: ‘Alloy design concepts for refined gamma titanium aluminide based alloys’, Intermetallics, 2007, 15, 451–460.
3.
HuD: ‘Effect of composition on grain refinement in TiAl-based alloys’, Intermetallics, 2001, 9, 1037–1043.
4.
LarsenDE: in‘Intermetallic matrix composites. Materials Research Society Symposium Proceedings’, Vol. 194, ‘Effect of XD TiB2 volume fraction on the microstructure of a cast near-gamma titanium aluminide alloy’, (ed. AntonD L, McMeekingR, MiracleD and MartinP), 285–292; 1990, Pittsburgh, PA, Materials Research Society.
5.
LarsenDE, ChristodoulouL, KampeSL and SadlerP: ‘Investment-cast processing of XD TM near-γ titanium aluminides’, Mater. Sci. Eng. A, 1991, A144, 45–49.
6.
GodfreyAB and LorettoMH: ‘The nature of complex precipitates associated with the addition of boron to a γ-based titanium aluminide’, Intermetallics, 1996, 4, 47–53.
7.
GosslarD, HartigC, GuntherR, HechtU and BormannR: ‘Heterogeneous nucleation and growth of the β (Ti) phase in the Ti–Al system – experiments and model calculations’, J. Phys. Condens. Matter, 2009, 21, 464111.
8.
EikenJ, ApelM, WitusiewiczVT, ZollingerJ and HechtU: ‘Interplay between α (Ti) nucleation and growth during peritectic solidification investigated by phase-field simulations’, J. Phys. Condens. Matter, 2009, 21, 464104.
9.
T. T. Cheng: ‘On the mechanism of boron-induced grain refinement in TiAl-based alloys’, Proc. of Symposium on ‘Gamma titanium aluminides 1999’, California, USA, February 1999, Warrendale, PA, 389–397.
10.
ChengTT: ‘The mechanism of grain refinement in TiAl alloys by boron addition – an alternative hypothesis’, Intermetallics, 2000, 8, 29–37.
11.
KitkamthornU, ZhangLC and AindowM: ‘The structure of ribbon borides in a Ti-44Al-4Nb-4Zr-1B alloy’, Intermetallics, 2006, 14, 759–769.
12.
HuangZW: ‘Inhomogeneous microstructure in highly alloyed cast TiAl-based alloys, caused by microsegregation’, Scr. Mater., 2005, 52, 1021–1025.
13.
HuD, HuangAJ, NovovicD and WuX: ‘The effect of boron and alpha grain size on the massive transformation in Ti–46Al–8Nb–xB alloys’, Intermetallics, 2006, 14, 818–825.
14.
HuD, YangC, HuangA, DixonM and HechtU: ‘Solidification and grain refinement in Ti45Al2Mn2Nb1B’, Intermetallics, 2012, 22, 68–76.
15.
BerminghamMJ, McDonaldSD, StJohnDH and DarguschMS: ‘Beryllium as a grain refiner in titanium alloys’, J. Alloys Compd, 2009, 481, L20–23.
16.
HechtU, WitusiewiczV, DrevermannA and ZollingerJ: ‘Grain refinement by low boron additions in niobium-rich TiAl-based alloys’, Intermetallics, 2008, 16, 969–978.
17.
YangC, JiangH, HuD, HuangA and DixonM: ‘Effect of boron concentration on phase transformation texture in as-solidified Ti44Al8NbxB’, Scr. Mater., 2012, 67, 85–88.
18.
HuD, YangC, HuangA, DixonM and HechtU: ‘Grain refinement in beta-solidifying Ti44Al8Nb1B’, Intermetallics, 2012, 23, 49–56.
19.
MaxwellI and HellawellA: ‘Simple model for grain refinement during solidification’, Acta Metall., 1975, 23, 229–237.
20.
TarshisLA, WalkerJL and RutterJW: ‘Experiments on the solidification structure of alloy castings’, Metall. Trans., 1971, 2, 2589–2597.
21.
JohnssonM, BackerudL and SigworthGK: ‘Study of the mechanism of grain refinement of aluminum after additions of Ti- and B-containing master alloys’, Metall. Mater. Trans. A, 1993, 24A, 481–491.
22.
EastonMA and JohnDHSt: ‘A model of grain refinement incorporating alloy constitution and potency of heterogeneous nucleant particles’, Acta Mater., 2001, 49, 1867–1878.
23.
DesnainP, FautrelleY, MeyerJL, RiquetJP and DurandF: ‘Prediction of equiaxed grain density in multicomponent alloys, stirred electromagnetically’, Acta Metall., 1990, 38, 1513–1523.
24.
EastonM and St JohnD: ‘Grain refinement of aluminum alloys: Part I. The nucleant and solute paradigms—a review of the literature’, Metall. Mater. Trans. A, 1999, 30A, 1613–1623.
25.
EastonM and St JohnD: ‘Grain refinement of aluminum alloys: Part II. Confirmation of, and a mechanism for, the solute paradigm’, Metall. Mater. Trans. A, 1999, 30A, 1625–1633.
26.
GreerAL, BunnAM, TroncheA, EvansPV and BristowDJ: ‘Modelling of inoculation of metallic melts: application to grain refinement of aluminium by Al–Ti–B’, Acta Mater., 2000, 48, 2823–2835.
27.
QuestedTE and GreerAL: ‘Grain refinement of Al alloys: mechanisms determining as-cast grain size in directional solidification’, Acta Mater., 2005, 53, 4643–4653.
28.
DuQ and LiY: ‘An extension of the Kampmann–Wagner numerical model towards as-cast grain size prediction of multicomponent aluminum alloys’, Acta Mater., 2014, 71, 380–389.
29.
St JohnDH, QianM, EastonMA and CaoP: ‘The interdependence theory: the relationship between grain formation and nucleant selection’, Acta Mater., 2011, 59, 4907–4921.
30.
QuestedTE, DinsdaleAT and GreerAL.: ‘Thermodynamic modelling of growth-restriction effects in aluminium alloys’, Acta Mater., 2005, 53, 1323–1334.
31.
EastonMA and St JohnDH: ‘An analysis of the relationship between grain size, solute content, and the potency and number density of nucleant particles’, Metall. Mater. Trans. A, 2005, 36A, 1911–1920.
32.
MenH and FanZ: ‘Effects of solute content on grain refinement in an isothermal melt’, Acta Mater., 2011, 59, 2704–2712.
33.
Schmid-FetzerR and KozlovA: ‘Thermodynamic aspects of grain growth restriction in multicomponent alloy solidification’, Acta Mater., 2011, 59, 6133–6144.
34.
HuD, WuX and LorettoMH: ‘Advances in optimisation of mechanical properties in cast TiAl alloys’, Intermetallics, 2005, 13, 914–919.
35.
KartavykhAV, TcherdyntsevVV, GorshenkovMV and KaloshkinSD: ‘Microstructure engineering of TiAl-based refractory intermetallics within power-down directional solidification process’, J. Alloys Compd, 2014, 586, 180–183.
36.
KartavykhAV, GorshenkovMV, TcherdyntsevVV and PodgornyDA: ‘On the state of boride precipitates in grain refined TiAl-based alloys with high Nb content’, J. Alloys Compd, 2014, 586, 183–188.
37.
JohnsonDR, MasudaY, InuiH and YamaguchiM: ‘Alignment of the TiAl:Ti3Al lamellar microstructure in TiAl alloys by directional solidification’, Mater. Sci. Eng. A, 1997, A239–A240, 577–583.
38.
YuY, LiXP, YeXM and HuJ: ‘Effect of overheating treatment on microstructure and crystal orientation of TbDyFe alloy’, Mater. Sci. Technol., 2013, 29, (6), 697–701.
