Adiabatic shear bands represent intense plastic deformation that is localised because the rate at which the heat generated by deformation is greater than that at which it is dissipated. The structure of such bands generated by ballistic testing is examined in order to reveal the governing mechanisms. We attempt to distinguish in particular whether local reaustenitisation occurs, or if the microstructural changes are simply a reflection of intense deformation.
TimothyS. P.: ‘The structure of adiabatic shear bands in metals: a critical review’, Acta Metall., 1987, 35, 301–306.
5.
DaviesW. J.: ‘Surface fatigue in ball bearings, roller bearings, and gears in aircraft engines’, in‘Fatigue in rolling contact’, 23–40; 1963, London, Institution of Mechanical Engineers.
6.
SchlichtH.: ‘About adiabatic shear bands and the generation of ‘high-angle white bands’ in roller bearings’,Materialwiss. Werkstofftech., 2008, 39, 217–226.
7.
BhadeshiaH. K. D. H.: ‘Steels for bearings’, Prog. Mater. Sci., 2012, 57, 268–435.
8.
NahmeH. and LachE.: ‘Dynamic behaviour of high strength armour steel’, J. Phys. IV, 1997, 7, 373–378.
9.
RogersH. C. and ShastryC. V.: ‘Material factors in adiabatic shear bands in steels’, in‘Shock waves and high-strain-rate phenomena in metals’, (ed. MeyersM. A. and MurrL. E.), 235–298; 1981, New York, Plenum Press.
10.
WittmanC. L., MeyersM. A. and PakH.-R.: ‘Observation of an adiabatic shear band in AISI 4340 steel by high-voltage transmission electron microscopy’, Metall. Trans. A, 1990, 21A, 707–716.
11.
BeattyJ. H., MeyerL. W., MeyersM. A. and Nemat-NasserS.: ‘Formation of controlled adiabatic shear bands in AISI 4340 high strength steel’, in‘Shock wave and high-strain-rate phenomena in metals’, (ed. MeyersM. A. et al.), 645–656; 1992, New York, Marcel Dekker.
12.
BassimM. N., OdeshiA. G. and BolducM.: ‘Deformation and failure of a rolled homogeneous armour steel under dynamic mechanical loading in compression’, Proc. 12th Int. Conf. on ‘Fracture’, New York, USA, July 2009, Curran Associates Inc., 3464–3473.
13.
BhadeshiaH. K. D. H.: ‘The first bulk nanostructured metal’, Sci. Technol. Adv. Mater., 2013, 14, 014202.
14.
CaballeroF. G., BhadeshiaH. K. D. H., MawellaK. J. A., JonesD. G. and BrownP.: ‘Design of novel high–strength bainitic steels: part I’, Mater. Sci. Technol., 2001, 17, 512–516.
15.
CaballeroF. G., BhadeshiaH. K. D. H., MawellaK. J. A., JonesD. G. and BrownP.: ‘Design of novel high–strength bainitic steels: part II’, Mater. Sci. Technol., 2001, 17, 517–522.
16.
NPL :‘MTDATA software’; 2006, Teddington, National Physical Laboratory.
17.
TsujiN., UejiR., MinaminoY. and SaitoY.: ‘New and simple process to obtain nano-structured bulk low-carbon steel with superior mechanical property’, Scr. Mater., 2002, 46, 305–310.
18.
ZhaoX., JingT., GaoY., QiaoG., ZhouJ. and WangW.: ‘Annealing behavior of nano-layered steel produced by heavy cold-rolling of lath martensite’, Mater. Sci. Eng. A, 2005, A397, 117–121.
19.
UejiR., TsujiN., MinaminoY. and KoizumiY.: ‘Ultragrain refinement of plain low carbon steel by cold-rolling and annealing of martensite’, Acta Mater., 2002, 50, 4177–4139.
20.
MachlinE. S. and CohenM.: ‘Burst phenomenon in the martensitic transformation’, Trans. Metall. Soc. AIME, 1951, 191, 746–754.
21.
FiedlerH. C., AverbachB. L. and CohenM.: ‘The effect of deformation on the martensitic transformation’, Trans. Am. Soc. Met., 1955, 47, 267–290.
22.
TsuzakiK., FukasakuS., TomotaY. and MakiT.: ‘Effect of prior deformation of austenite on the gamma-epsilon martensitic transformation in Fe–Mn alloys’, Trans. JIM, 1991, 32, 222–228.
23.
ShipwayP. H. and BhadeshiaH. K. D. H.: ‘Mechanical stabilisation of bainite’, Mater. Sci. Technol., 1995, 11, 1116–1128.
24.
ChatterjeeS., WangH. S., YangJ. R. and BhadeshiaH. K. D. H.: ‘Mechanical stabilisation of austenite’, Mater. Sci. Technol., 2006, 22, 641–644.
25.
MaalekianM., KozeschnikE., ChatterjeeS. and BhadeshiaH. K. D. H.: ‘Mechanical stabilisation of eutectoid steel’, Mater. Sci. Technol., 2007, 23, 610–612.
