Improvement of water slot design for beam blank casting mould

Abstract

Two-dimensional thermo–elastic–plastic creep finite element models of two beam blank moulds with different water slot designs, the large hole mould and the small hole mould, are set up and their thermomechanical behaviour is numerically investigated by means of ABAQUS software. The temperature, distortion, stress and inelastic strain range across the hot faces as well as the fatigue life of the two moulds are discussed in detail, based on which it is shown that the distributions of temperature and distortion of the small hole mould are more uniform than those of the large hole mould, and the peak temperature of the former mould is smaller than that of the later mould. However, the fatigue life of the small hole mould is shorter than that of the large hole mould. Both moulds were put into service in an industry and it is demonstrated that the quality of the product cast by the small hole mould is better than that by the large hole mould, and the service life of the small hole mould is longer than that of the large hole mould because the service life of a mould chiefly depends on the wear of its hot face, which is much shorter than the fatigue life. An improved water slot design for the beam blank mould is then proposed and it is numerically demonstrated that this improved mould is superior to the large hole mould and the small hole mould.

Get full access to this article

View all access options for this article.

References

Hoedi

Wimmer

and Mayrhofer

K. F.

: ‘VAI beam-blank casting technology’, Steel Times Int., 2002, 26, (9), 28–30.

Hashimoto

Ohnishi

Yamaguchi

Kinugawa

and Ueda

: ‘An analysis of the thermal load of mould plates in a continuous casting plant’, Hitachi Zosen Tech. Rev., 1982, 43, (3), 1–9.

Thomas

B. G.

Moitra

and Habing

: ‘Analysis of thermal and mechanical behaviour of copper moulds during continuous casting of steel slabs’, Iron Steelmaker, 1998, 25, (10), 125–143.

Langeneckert

: ‘Influence of mould geometry on heat transfer, thermocouple and mould temperatures in the continuous casting of steel slabs’, Master’s dissertation, University of Illinois, Champaign, IL, USA, 2001.

Thomas

B. G.

Langeneckert

Castellá

Dziuba

di Gresia

and Balante

: ‘Optimisation of narrow face water slot design for Siderar slab casting mould’, Ironmaking Steelmaking, 2003, 30, (3), 235–239.

Peng

Zhou

and Qin

: ‘Improvement of the temperature distribution in continuous casting moulds through the rearrangement of the cooling water slots’, J. Mater. Process. Technol., 2005, 167, (2–3), 508–514.

Thomas

B. G.

Jiang

and Lorento

: ‘Optimization of water channel design in beam-blank moulds’, Proc. 5th Eur. Continuous Casting Conf., Nice, France, 2005, The Institute of Materials, Minerals and Mining, 139–147.

Hibbeler

L. C.

and Thomas

B. G.

: ‘Thermo-mechancial modeling of beam blank casting’, Proc. AISTech 2008 Conf., Pittsburgh, PA, USA, 2008, Association for Iron and Steel Technology, 135–148.

H. L.

Wen

G. H.

Sun

Wang

K. Z.

Yan

and Luo

: ‘Thermal behaviour of moulds with different water channels and their influence on quality in continuous casting of beam blank’, Ironmaking Steelmaking, 2010, 37, (5), 380–386.

10.

H. L.

Wen

G. H.

Sun

Wang

K. Z.

and Yan

: ‘Analysis of thermal behaviour for beam blank continuous casting mould’, J. Iron Steel Res., 2010, 17, (12), 17–22.

11.

Liu

X. D.

and Zhu

M. Y.

: ‘Finite element analysis of thermal and mechanical behaviour in a slab continuous casting mould’, ISIJ Int., 2006, 46, (11), 1652–1659.

12.

Luo

Yan

Xiong

Y. X.

Wen

G. H.

and Xu

H. L.

: ‘Improvement to secondary cooling scheme for beam blank continuous casting’, Ironmaking Steelmaking, 2012, 39, (2), 125–132.

13.

Thomas

B. G.

and Stubbins

J. F.

: ‘Modeling creep and fatigue of copper alloys’, Metall. Mater. Trans. A, 2000, 31A, (10), 2491–2502.

14.

Park

J. K.

: ‘Thermo-mechanical phenomena in high speed continuous casting processes’, PhD thesis, University of British Columbia, Vancouver, Canada, 2002.

15.

Ashida

and Takao

: ‘Thermal fatigue strength of copper alloy’, Hitachi Zosen Tech. Rev., 1984, 45, (2), 70–76.