Aluminium alloy sheets were joined to stainless steel ones by a resistance spot welding method using Al–Mg alloy interlayer. The interlayer exhibits a lower melting point than the Al alloy. Consequently, melted interlayer with a lower temperature filled the gap between the two sheets and resulted in effective joining. Subsequently, tensile shear fatigue tests had been conducted to evaluate fatigue strength and to determine the fatigue fracture mechanism. Resistance spot welding dissimilar welds exhibited higher fatigue strengths than friction stir spot welded dissimilar ones. Fatigue fracture modes were dependent on the load levels, where plug type fracture occurred at high load levels, shear fracture through the nugget at medium load levels and through thickness fatigue crack propagation in the Al sheet at low load levels. The fracture mode transition was attributed to the geometrical rotation around the nugget.
LiyanageT., KilbourneJ., GerlichA. P. and NorthT. H.: ‘Joint formation in dissimilar Al alloy/steel and Mg alloy/steel friction stir spot welds’, Sci. Technol. Weld. Join., 2009, 14, (6), 500–508.
2.
LeeC. Y., ChoiD. H., YeonY. M. and JungS. B.: ‘Dissimilar friction stir spot welding of low carbon steel and Al–Mg alloy by formation of IMCs’, Sci. Technol. Weld. Join., 2009, 14, (3), 216–220.
3.
da SilvaA. A. M., AldanondoE., AlvarezP., ArrutiE. and EcheverríaA.: ‘Friction stir spot welding of AA 1050 Al alloy and hot stamped boron steel (22MnB5)’, Sci. Technol. Weld. Join., 2010, 15, (8), 682–687.
4.
BozziS., Helbert-EtterA. L., BaudinT., CriquiB. and KerbiguetJ. G.: ‘Intermetallic compounds in Al 6016/IF-steel friction stir spot welds’, Mater. Sci. Eng. A, 2010, A527, 4505–4509.
5.
UematsuY., TokajiK., TozakiY., NakashimaY. and ShimizuT.: ‘Fatigue behaviour of dissimilar friction stir spot welds between A6061-T6 and low carbon steel sheets welded by a scroll grooved tool without probe’, Fatigue Fract. Eng. Mater. Struct., 2011, 34, (8), 581–591.
6.
UematsuY., KakiuchiT., TozakiY. and KojinH.: ‘Comparative study of fatigue behaviour in dissimilar Al alloy/steel and Mg alloy/steel friction stir spot welds fabricated by scroll grooved tool without probe’, Sci. Technol. Weld. Join., 2012, 17, (5), 348–356.
7.
YasuyamaM., OgawaK. and TakaT.: ‘Spot welding of aluminum and steel sheet with insert of aluminum clad steel sheet’, Q.J. Jpn Weld. Soc., 1996, 14, (2), 314–320.
8.
OikawaH., OhmiyaS., YoshimuraT. and SaitohT.: ‘Resistance spot welding of steel and aluminium sheet using insert metal sheet’, Sci. Technol. Weld. Join., 1999, 4, (2), 80–88.
9.
SatonakaS., IwamotoC., QiuR. and FujiokaT.: ‘Trends and new application of spot welding for aluminum alloy sheets’, Weld. Int., 2006, 20, (11), 858–864.
10.
QiuR., IwamotoC. and SatonakaS.: ‘The influence of reaction layer on the strength of aluminum/steel joint welded by resistance spot welding’, Mater. Charact., 2009, 60, 156–159.
11.
QiuR., IwamotoC. and SatonakaS.: ‘Interfacial microstructure and strength of steel/aluminum alloy joints welded by resistance spot welding with cover plate’, J. Mater. Process. Technol., 2009, 209, 4186–4193.
12.
QiuR., ShiH., ZhangK., TuY., IwamotoC. and SatonakaS.: ‘Interfacial characterization of joint between mild steel and aluminum alloy welded by resistance spot welding’, Mater. Charact., 2010, 61, 684–688.
13.
AkdenizM. V. and MekhrabovA. O.: ‘The effect of substitutional impurities on the evolution of Fe-Al diffusion layer’, Acta Mater., 1998, 46, 1185–1192.
14.
ZhangW. H., QuiX. M., SunD. Q. and HanL. J.: ‘Effects of resistance spot welding parameters on microstructures and mechanical properties of dissimilar material joints of galvanized high strength steel and aluminium alloy’, Sci. Technol. Weld. Join., 2011, 16, (2), 153–161.
15.
XuW., ChenD. L., LiuL., MoriH. and ZhouY.: ‘Microstructure and mechanical properties of weld-bonded and resistance spot welded magnesium-to-steel dissimilar joints’, Mater. Sci. Eng. A, 2012, A537, 11–24.
16.
PennerP., LiuL., GerlichA. and ZhouY.: ‘Feasibility study of resistance spot welding of dissimilar Al/Mg combinations with Ni based interlayers’, Sci. Technol. Weld. Join., 2013, 18, (7), 541–550.
17.
LiY., ZhangY. and LuoZ.: ‘Microstructure and mechanical properties of Al/Ti joints welded by resistance spot welding’, Sci. Technol. Weld. Join., 2015, 20, (5), 385–394.
18.
MatsudaC., YunK., KongJ., YanaseS., OkumiyaM., IshakI., KakiuchiT. and UematsuY.: ‘Relation between heat source and electrode force of dissimilar metal welding’, Int. J. Metall. Mater. Sci. Eng., 2015, 5, (7), 1–6.
19.
MatsudaC., YanaseS., KyyoulY., UematsuY., KongJ. and OkumiyaM.: ‘Resistance spot welding between stainless steel and aluminum alloy plate with an insert material’, Proc. 8th, Conf. the Soc. Mater. Sci., Japan, Tokai Branch, Nagoya, Japan, March 2014, Meijo University, 53–24(in Japanese).
20.
UematsuY. and TokajiK.: ‘Comparison of fatigue behaviour between resistance spot and friction stir spot welded aluminium alloy sheets’, Sci. Technol. Weld. Join., 2009, 14, (1), 62–71.
