Owing to the rapid cooling rates, the deposited and base metals could be mixed incompletely during laser welding of Al alloys in most cases. The objective of this research is to explore a possible method to promote the mixing of materials inside the molten pool by making use of the magnetofluid dynamic effect of electric current. Full penetration CO2 laser welding of 3 mm thick alloy 6009 sheets was performed with an external electric current simultaneously into the weld pool via a filler wire. It is found that the deposited metal is mainly concentrated on the upper part of the weld fusion zone, and the weld zone microstructure is non-uniform without the electric current addition. With the application of an electric current, the weld fusion zone geometry is reshaped, and the chemical composition and microstructure of the weld metal are homogenised. The mechanism is found to be electromagnetic force stirring of the molten pool.
CaoX., WallaceW., PoonC. and ImmarigeonJ. P.: ‘Research and progress in laser welding of wrought aluminum alloys. I: laser welding processes’, Mater. Manuf. Process, 2003, 18, (1), 1–22. doi: 10.1081/AMP-120017586
5.
CaoX., WallaceW., ImmarigeonJ. P. and PoonC.: ‘Research and progress in laser welding of wrought aluminum alloys. II: metallurgical microstructures, defects, and mechanical properties’, Mater. Manuf. Processes, 2003, 18, (1), 23–49. doi: 10.1081/AMP-120017587
6.
KernM., BergerP. and HügelH.: ‘Magneto-fluid dynamic control of seam quality in CO2 laser beam welding’, Weld. J., 2000, 79, (3), 72–78.
7.
AmbrosyG., AvilovV. V., BergerP. and HügelH.: ‘Laser induced plasma as a source for an intensive current to produce electromagnetic forces in the weld pool’. Proc. XIV Int. Symp. on ‘Gas flow, chemical lasers, and high-power lasers, Gmunden, Austria, September 2006, Bellingham, WA, SPIE, Vol. 6346, 63461Q.
8.
KawahitoY., KinoshitaK., MatsumotoN., MizutaniM. and KatayamaS.: ‘Effect of weakly ionised plasma on penetration of stainless steel weld produced with ultra high power density fiber laser’, Sci. Technol. Weld. Join., 2008, 13, (8), 749–753. doi: 10.1179/136217108X356971
9.
KawahitoY., MatsumotoN., MizutaniM. and KatayamaS.: ‘Characterisation of plasma induced during high power fibre laser welding of stainless steel’, Sci. Technol. Weld. Join., 2008, 13, (8), 744–748. doi: 10.1179/136217108X329313
10.
VollertsenF. and ThomyC.: ‘Magnetic stirring during laser welding of aluminum’, J. Laser Appl., 2006, 18, (1), 28–34. doi: 10.2351/1.2164477
11.
TangZ. and GatzenM.: ‘Influence on dilution by laser welding of al alloy with magnetic stirring’, Phys. Procedia, 2010, 5, 125–137. doi: 10.1016/j.phpro.2010.08.037
12.
AmbrosyG., BergerP., HügelH. and LindenauD.: ‘The use of electromagnetic body forces to enhance the quality of laser welds’, Proc. XIV Int. Symp. on ‘Gas flow, chemical lasers, and high-power lasers, Wroclaw, Poland, August 2003, Bellingham, WA, SPIE, Vol. 5120596–600.
13.
AvilovV. V., GumenyukA., LammersM. and RethmeierM.: ‘PA position full penetration high power laser beam welding of up to 30 mm thick AlMg3 plates using electromagnetic weld pool support’, Sci. Technol. Weld. Join., 2012, 17, (2), 128–133. doi: 10.1179/1362171811Y.0000000085
14.
BachmannM., AvilovV. V., GumenyukA. and RethmeierM.: ‘Numerical simulation of full-penetration laser beam welding of thick aluminium plates with inductive support’, J. Physica D, 2012, 45D, (3), 035201. doi: 10.1088/0022-3727/45/3/035201
15.
XiaoR. S., AmbrosyG., ZuoT. C. and HügelH.: ‘New approach to improve the laser welding process of aluminum by using an external electrical current’, J. Mater. Sci. Lett., 2001, 20, (23), 2163–2165. doi: 10.1023/A:1013792802211
16.
XiaoR. S., ZuoT. C., AmbrosyG. and HügelH.: ‘CO2 Laser beam welding of aluminum alloys with electric current addition’, Proc. 23rd Int. Conf. on ‘Applications of laser and electro-optics, San Francisco, CA, USA, October 2004, Bellingham, WA, SPIE, 163–168.
17.
XiaoR. S., ZuoT. C., LeimserM. and HügelH.: ‘Nd: YAG laser beam welding of aluminum in addition with an electric current’, Proc. Int. Conf. on ‘Lasers in material processing and manufacturing II, Beijing, China, November 2005, Bellingham, WA, SPIE, Vol. 5629. 195–201.
18.
XiaoR. S. and ZhangX. Y.: ‘Problems and issues in laser beam welding of aluminum-lithium alloys’, J. Manuf. Processes, 2014, 16, (2), 166–175. doi: 10.1016/j.jmapro.2013.10.005
19.
VollertsenF., BuschenhenkeF. and SeefeldT.: ‘Reduction of hot cracking in laser welding using hypereutectic AlSi filler wire’, Weld. World, 2008, 52, (5-6), 3–8. doi: 10.1007/BF03266635
20.
ZhaoH., WhiteD. R. and DebroyT.: ‘Current issues and problems in laser welding of automotive aluminum alloys’, Int. Mater. Rev., 1999, 44, (6), 238–266. doi: 10.1179/095066099101528298
21.
MatsunawaA., KimJ. D., SetoN., MizutaniM. and KatayamaS.: ‘Dynamics of keyhole and molten pool in laser welding’, J. Laser Appl., 1998, 10, (6), 247–254. doi: 10.2351/1.521858
22.
KawahitoY., MizutaniM. and KatayamaS.: ‘Elucidation of high-power fiber laser welding phenomena of stainless steel and effect of factors on weld geometry’, J. Phys. D, 2007, 40D, (19), 5854–5859. doi: 10.1088/0022-3727/40/19/009
