In this work, the feasibility of friction stir lap welding an aluminium alloy (Al-5083) to the aluminium clad steel sheet was studied. The welded joints were characterised by various methods including shear–tensile test and optical microscopy and scanning electron microscopy. The results indicated that sound and defect free joints were obtained. The fracture loads of the samples reached up to 94% compared with that of the steel base metal. Moreover, the joint strength linearly increased with the decrease in thickness of the aluminium layer roll bonded on the steel sheet. It was also shown that welding rotation and travel speed variation did not considerably impact the fracture loads in the studied range.
JiangWH, KovacevicR: ‘Feasibility study of friction stir welding of 6061-T6 aluminium alloy with AISI 1018 steel’, Proc. IMechE, 2004, 218, (10), 1323.
2.
ChenCM, KovacevicR: ‘Joining of Al 6061 alloy to AISI 1018 steel by combined effects of fusion and solid state welding’, Int. J. Mach. Tools Manuf., 2004, 44, (11), 1205–1214.
3.
SongJL, LinSB, YangCL, FanCL: ‘Effects of Si additions on intermetallic compound layer of aluminum–steel TIG welding–brazing joint’, J. Alloys Compd, 2009, 488, (1), 217–222.
4.
SongJL, LinSB, YangCL, FanCL, MaGC: ‘Analysis of intermetallic layer in dissimilar TIG welding–brazing butt joint of aluminium alloy to stainless steel’, Sci. Technol. Weld. Joining, 2010, 15, (3), 213–218.
5.
LeeCY, ChoiDH, YeonYM, JungSB: ‘Dissimilar friction stir spot welding of low carbon steel and Al–Mg alloy by formation of IMCs’, Sci. Technol. Weld. Joining, 2009, 14, (3), 216–220.
6.
LiyanageT, KilbourneJ, GerlichAP, NorthTH: ‘Joint formation in dissimilar Al alloy/steel and Mg alloy/steel friction stir spot welds’, Sci. Technol. Weld. Joining, 2009, 14, 500–508.
da SilvaAAM, AldanondoE, AlvarezP, ArrutiE, EcheverríaA: ‘Friction stir spot welding of AA 1050 Al alloy and hot stamped boron steel (22MnB5)’, Sci. Technol. Weld. Joining, 2010, 15, (8), 682–687.
15.
ChenYC, KomazakiT, KimYG, TsumuraT, NakataK: ‘Interface microstructure study of friction stir lap joint of AC4C cast aluminum alloy and zinc-coated steel’, Mater. Chem. Phys., 2008, 111, (2–3), 375–380.
16.
ChenYC, NakataK: ‘Effect of the surface state of steel on the microstructure and mechanical properties of dissimilar metal lap joints of aluminum and steel by friction stir welding’, Metall. Mater. Trans. A: Phys. Metall. Mater. Sci., 2008, 39A, (8), 1985–1992.
17.
ZhangG, SuW, ZhangJ, WeiZ: ‘Friction stir brazing: a novel process for fabricating Al/steel layered composite and for dissimilar joining of Al to steel’, Metall. Mater. Trans. A: Phys. Metall. Mater. Sci., 2011, 42A, (9), 2850–2861.
18.
MovahediM, KokabiAH, Seyed ReihaniSM: ‘Investigation on the bond strength of Al-1100/St-12 roll bonded sheets, optimization and characterization’, Mater. Des., 2011, 32, (6), 3143–3149.
19.
HumpstonG, JacobsonDM: ‘Principles of soldering and brazing’, 18–136; 1996, Materials Park, OH, ASM.
20.
Madaah-HosseiniHR, KokabiAH: ‘Cold roll bonding of 5754-aluminum strips’, Mater. Sci. Eng. A, 2002, A335, (1–2), 186–190.
