The deformation behaviour of AISI 304L stainless steel was examined under uniaxial tension and shear deformation modes in the temperature range of 0–500°C. A linear relationship between the tensile and shear yield stresses was observed over the whole temperature range, which was in a good agreement with the predictions of the von-Mises criterion. The relationship between the ultimate shear and tensile strength values, however, showed three distinct temperature-dependent regimes. In the temperature ranges corresponding to the transformation-induced plasticity effect and the dynamic strain aging phenomenon, a deviation from the expected behaviour was observed, which was related to the dependency of these phenomena on the loading mode.
LeonCADrewRAL.Small punch testing for assessing the tensile strength of gradient Al/Ni–SiC composites. Mater Lett. 2002; 56:812–816.
2.
GuduruRKWongPZDarlingKADetermination of activation volume in nanocrystalline Cu using the shear punch test. Adv Eng Mater. 2007; 9:855–859.
3.
ZhangLElwazriAMZimmerlyTShear punch testing and fracture toughness of bulk nanostructured silver. Mater Des. 2009; 30:1445–1450.
4.
Hoseini-AtharMMMahmudiRBabuRPMicrostructure, texture, and strain-hardening behavior of extruded Mg–Gd–Zn alloys. Mater Sci Eng A. 2020; 772:138833.
5.
GuduruRKDarlingKAKishoreREvaluation of mechanical properties using shear–punch testing. Mater Sci Eng A. 2005; 395:307–314.
6.
WanjaraPDrewRALYueS.Application of small specimen testing technique for mechanical property assessment of discontinuously reinforced composites. Mater Sci Technol. 2006; 22:61–71.
7.
KarthikVVisweswaranPVijayraghavanATensile–shear correlations obtained from shear punch test technique using a modified experimental approach. J Nucl Mater. 2009; 393:425–432.
8.
MahmudiRSadeghiM.Correlation between shear punch and tensile strength for low-carbon steel and stainless steel sheets. J Mater Eng Perform. 2013; 22:433–438.
9.
MasoudpanahSMMahmudiR.The microstructure, tensile, and shear deformation behavior of an AZ31 magnesium alloy after extrusion and equal channel angular pressing. Mater Des. 2010; 31:3512–3517.
10.
MasoudpanahSMMahmudiRLangdonTG.Correlation between shear punch and tensile measurements for an AZ31Mg alloy processed by equal-channel angular pressing. Kovove Mater. 2011; 49:43–50.
11.
LiJZhouZWangSDeformation mechanisms and enhanced mechanical properties of 304L stainless steel at liquid nitrogen temperature. Mater Sci Eng A. 2020; 798:140133.
12.
JärvenpääAJaskariMKiskoAProcessing and properties of reversion-treated austenitic stainless steels. Metals. 2020; 10:281.
13.
GauzziFMontanariRPrincipiGAISI 304 steel: anomalous evolution of martensitic phase following heat treatments at 400°C. Mater Sci Eng A. 2006; 438–440:202–206.
14.
SunGDuLHuJOn the influence of deformation mechanism during cold and warm rolling on annealing behavior of a 304 stainless steel. Mater Sci Eng A. 2019; 746:341–355.
15.
HamadaASKarjalainenLPMisraRDKContribution of deformation mechanisms to strength and ductility in two Cr–Mn grade austenitic stainless steels. Mater Sci Eng A. 2013; 559:336–344.
16.
ZerganiAMirzadehHMahmudiR.Unraveling the effect of deformation temperature on the mechanical behavior and transformation-induced plasticity of the SUS304L stainless steel. Steel Res Int. 2020; 91:2000114.
17.
SoleimaniMKalhorAMirzadehH.Transformation-induced plasticity (TRIP) in advanced steels: A review. Mater Sci Eng A. 2020; 795:140023.
18.
HeckerSSStoutMGStaudhammerKPEffects of strain state and strain rate on deformation-induced transformation in 304 stainless steel: Part I. Magnetic measurements and mechanical behavior. Metall Trans A. 1982; 13:619–626.
19.
ChoudharyBK.Influence of strain rate and temperature on tensile deformation and fracture behavior of type 316L (N) austenitic stainless steel. Metall Trans A. 2014; 45:302–316.
20.
KarlsenWIvanchenkoMEhrnsténUMicrostru-ctural manifestation of dynamic strain aging in AISI 316 stainless steel. J Nucl Mater. 2009; 395:156–161.
21.
FuSChengTZhangQTwo mechanisms for the normal and inverse behaviors of the critical strain for the Portevin–Le Chatelier effect. Acta Mater. 2012; 60:6650–6656.
22.
ZerganiAMirzadehHMahmudiR.Evolutions of mechanical properties of AISI 304L stainless steel under shear loading. Mater Sci Eng A. 2020; 791:139667.
23.
KaramiMMahmudiR.Work hardening behavior of the extruded and equal-channel angularly pressed Mg–Li–Zn alloys under tensile and shear deformation modes. Mater Sci Eng A. 2014; 607:512–520.
24.
KaramiMMahmudiR.Orientation-dependent micro-structure and shear flow behavior of extruded Mg–Li–Zn alloys. Mater Sci Eng A. 2015; 636:493–501.
25.
ShirdelMMirzadehHParsaMH.Nano/ultrafine grained austenitic stainless steel through the formation and reversion of deformation-induced martensite: Mechanisms, microstructures, mechanical properties, and TRIP effect. Mater Charact. 2015; 103:150–161.
26.
TalonenJHänninenH.Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels. Acta Mater. 2007; 55:6108–6118.
27.
WeißAGutteHSchellerPR.Deformation induced martensite formation and its effect on transformation induced plasticity (TRIP). Steel Res Int. 2006; 77:727–732.
28.
DieterGEBaconD.Mechanical metallurgy. New York: McGraw-hill; 1986.
29.
LucasGE.The development of small specimen mechanical test techniques. J Nucl Mater. 1983; 117:327–339.
30.
NaghizadehMMirzadehH.Modeling the kinetics of deformation-induced martensitic transformation in AISI 316 metastable austenitic stainless steel. Vacuum. 2018; 157:243–248.
31.
OdnobokovaMBelyakovAKaibyshevR.Development of nanocrystalline 304L stainless steel by large strain cold working. Metals. 2015; 5:656–668.
32.
OdnobokovaMBelyakovAEnikeevNAnnealing behavior of a 304L stainless steel processed by large strain cold and warm rolling. Mater Sci Eng A. 2017; 689:370–383.
33.
KarjalainenLPTaulavuorlTSellmanMSome strengthening methods for austenitic stainless steels. Steel Res Int. 2008; 79:404–412.
34.
SohrabiMJNaghizadehMMirzadehH.Deformation-induced martensite in austenitic stainless steels: A review. Arch Civ Mech Eng. 2020; 20:124.
