A methodology has been developed using a non-destructive ultrasonic technique for measuring surface/subsurface residual stresses in 7 mm thick AISI type 316LN stainless steel weld joints made by activated tungsten inert gas and multipass tungsten inert gas welding processes. Measurement of residual stresses using an ultrasonic technique is based on the effect of stresses on the propagation velocity of elastic waves. Critically refracted longitudinal LCR wave mode was employed and accurate transit time measurements were made across the weld joints. Quantitative values of the longitudinal residual stresses across the weld joints were estimated from the measured transit times and predetermined value of acoustoelastic constant for AISI type 316LN stainless steel. The nature of the residual stress profiles and their variations across the two types of weld joints were compared and interpreted.
MitsubuchiK.: in ‘Nondestuctive methods for material property determination’, (ed. C. O. Ruud and R. E. Reen, Jr), 123–134; 1984, London, Plenum Press.
3.
PalanichamyP., JosephA., KasiviswanathanK. V., BhattacharyaD. K. and Baldev Raj: in ‘Welding Engineering Handbook’, (ed. S. Sundararajan et al.), Vol. I, 269–294; 1990, Secundrabad, Radiant Publishing Pvt. Ltd.
4.
RavisankarK., NarayananR., Jeyarama RaoG. and Appa RaoT. V. S. R.: J. Struct. Eng., 1985, 12, (1), 88–96.
5.
WithersP. J. and BhadeshiaH. K. D. H.: Mater. Sci. Technol., 2001, 17, (4), 355–365.
6.
Satish Dronavalli: ‘Residual stress measurements and analysis by destructive and non destructive techniques’, Master of Science Engineering Thesis, Department of Mechanical Engineering, Howard R. Hughes College of Engineering, University of Nevada, Las Vegas, NV, USA, 2004.
7.
‘Standard method for determining residual stresses by hole drilling strain gauge method’, E837–85, ASTM, Philadelphia, PA, 1985.
8.
JeyaramanG., RavisankarK. and NarayananR.: J. Testing and Evaluation, 1986, 14, (4), 207–212.
9.
‘Measurement of residual stress by hole drilling strain gauge method’, TN-503–2, Measurements Group, Inc., Rayleigh, NC, USA, 1986.
10.
PraskH. J. and ChoiC. S.: J. Nucl. Mater., 1984, 126, 124–131.
11.
LorontzenJ.: NDT Int., 1988, 21, (6), 385–388.
12.
NayanI. C. and CohenJ. C.: ‘Residual stress measurements by diffraction and interpretation’; 1987, New York, Springer-Verlag.
13.
JiliesD. C.: NDT Int., 1988, 21, (6), 311–319.
14.
LoC. C. H., PaulsenJ. A., KinserE. R. and JilesD. C.: IEEE Trans. Magn., 2004, 40, (4), 2173–2175.
15.
HsuN. N.: Exp. Mech., 1974, 14, (5), 169–176.
16.
KinoG. S. and ShawJ. H.: ‘Acoustic techniques for measuring stress regions in materials’, Report EPRI, NP-1043, Stanford University, Stanford, CA, USA, 1979.
17.
LuthiT.: NDT Int., 1990, 23, (6), 117–121.
18.
DikeJ. J. and JohnsonG. C.: NDT Int., 1995, 28, (2), 117–125.
SankarB. N., PalanichamyP., RajkumarK. V. and JayakumarT.: Proc. Int. Conf. on ‘Ultrasonics’ (ICEU’99), New Delhi, India, December 1999, National Physical Laboratory, Vol. 2, 391–394.
21.
SankarB. N., PalanichamyP., JayakumarT., KalyanasundaramP. and Baldev Raj: Proc. 15th WCNDT, Rome, Italy, October 2000, AIPND Italian Society for Nondestructive Testing Monitoring Diagnostics. See http://www.ndt.net/article/wcndt00/papers/idn688/idn688.htm
22.
BrayD. E.: Proc. 15th World Conf. on ‘Non-destructive testing’, Rome, Italy, October 2000, AIPND Italian Society for Nondestructive Testing Monitoring Diagnostics. See http://www.ndt.net/article/wcndt00/papers/idn647/idn647.htm
23.
BrayD. E. and TangW.: Nucl. Eng. Design, 2001, 207, 231–240.
24.
BelahceneF. and LuJ.: J. Strain Anal., 2002, 37, (1), 13–20.
25.
LuH., LiuX. S., YangJ. G., ZhangS. P. and FangH. Y.: Sci Technol. Weld. Join., 2008, 13, (1), 70–74.
26.
CrecraftD. L.: Ultrasonics, 1968, 4, 117–121.
27.
PaskellT., LundinC. and CastnerH.: Weld. J., 1997, 76, (4), 57–62.
HuangH. Y., ShyuS. W., TsengK. H. and ChouC. P.: Sci. Technol. Weld. Join., 2005, 10, (5), 566–573.
30.
VasudevanM.: ‘Computational and experimental studies on arc welded austenitic stainless steels’, PhD Thesis, Indian Institute of Technol., Chennai, 2007.
31.
VasudevanM., BhaduriA. K. and Baldev Raj: Proc. Int. Inst. Weld. Int. Cong. 2008, Chennai, India, January 2008, Indian Institute of Welding, 211–218.
32.
FisherM. J. and HerrmanG.: ‘Review of progress in quantitative NDE’, (ed. D. O. Thompson and D. E. Chimenti), 1283–1291; 1988, New York, Plenum Press.
33.
BulanovaT., FedoseevA., KalininG., RodchenkovB. and ShamardinV.: J. Nucl. Mater., 2004, 329–333, (1), 639–642.
