Cutting force for conventional orthogonal machining can be predicted by Merchant’s Circle Diagram (MCD) considering the shearing action of chip formation. However, the effect of plowing action is significant for micro turning, which has not been considered in MCD. Therefore, a large error has been observed in the prediction of cutting force in micro turning by MCD theory. In this study, a compensated model has been developed for orthogonal micro turning based on MCD. The theory has taken shearing and plowing actions into consideration. The compensated model involved material flow stress, cutting parameters, and tool geometry, including cutting edge radius. This model has predicted tangential cutting force with an average prediction error of 3.75% for micro turning of Ti6Al4V, whereas the average prediction error was 14.9% for axial cutting force.
SinghS, GhaiV, AgrawalA, . Effect of machining parameters on cutting force during micro-turning of a brass rod. Mater Manuf Process2019; 34: 1816–1823. DOI: 10.1080/10426914.2019.1675887.
2.
WuX, LiL, HeN, . Influence of the cutting edge radius and the material grain size on the cutting force in micro cutting. Precis Eng2016; 45: 359–364. DOI: 10.1016/j.precisioneng.2016.03.012.
3.
ChenX, ChengK and WangC. Design of a smart turning tool with application to in-process cutting force measurement in ultraprecision and micro cutting. Manuf Lett2014; 2: 112–117. DOI: 10.1016/j.mfglet.2014.07.001.
4.
ZhangC, EhmannK and LiY. Analysis of cutting forces in the ultrasonic elliptical vibration-assisted micro-groove turning process. Int J Adv Manuf Technol2015; 78: 139–152. DOI: 10.1007/s00170-014-6628-3.
5.
ZhuZ, ToS, ZhuW, . Cutting forces in fast- / slow tool servo diamond turning of micro-structured surfaces. Int J Mach Tools Manuf2019; 136: 62–75.
6.
JagadeshT and SamuelGL. Mechanistic and finite element model for prediction of cutting forces during Micro-Turning of Titanium Alloy. Mach Sci Technol2015; 19: 593–629. DOI: 10.1080/10910344.2015.1085318.
7.
MerchantME. Mechanics of the metal cutting process. I. Orthogonal cutting and a type 2 chip. J Appl Phys1945; 16: 267–275. DOI: 10.1063/1.1707586.
8.
WuX, LiL, ZhaoM, . Experimental investigation of specific cutting energy and surface quality based on negative effective rake angle in micro turning. Int J Adv Manuf Technol2016; 82: 1941–1947. DOI: 10.1007/s00170-015-7548-6.
9.
NixWD and GaoH. Indentation size effects in crystalline materials: A law for strain gradient plasticity. J Mech Phys Solids1998; 46: 411–425. Epub ahead of print 1998. DOI: 10.1016/S0022-5096(97)00086-0.
10.
JohnsonGR and CookWH. Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures. Eng Fract Mech1985; 21: 31–48. DOI: 10.1016/0013-7944(85)90052-9.
11.
ShawMC. Metal cutting principles. New York: Oxford University Press; 2005.
12.
HuangJ and AifantisEC. Note on the problem of shear localization during chip formation in orthogonal machining. J Mater Eng Perform1997; 6: 25–26. DOI: 10.1007/s11665-997-0027-y.
13.
LeeWS and LinCF. High-temperature deformation behaviour of Ti6A14V alloy evaluated by high strain-rate compression tests. J Mater Process Technol1998; 75: 127–136.
14.
SunJ and GuoYB. Material flow stress and failure in multiscale machining titanium alloy Ti-6Al-4V. Int J Adv Manuf Technol2009; 41: 651–659. DOI: 10.1007/s00170-008-1521-6.
15.
BoujelbeneM. Investigation and modeling of the tangential cutting force of the Titanium alloy Ti-6Al-4V in the orthogonal turning process. In:Procedia Manuf. 2018; 20: 571–577. DOI: 10.1016/j.promfg.2018.02.085.
16.
LaiX, LiH, LiC, . Modelling and analysis of micro scale milling considering size effect, micro cutter edge radius and minimum chip thickness. Int J Mach Tools Manuf2008; 48: 1–4. DOI: 10.1016/j.ijmachtools.2007.08.011.
17.
TounsiN, VincentiJ, OthoA, . From the basic mechanics of orthogonal metal cutting toward the identification of the constitutive equation. Int J Mach Tools Manuf2002; 42: 1373–1383. DOI: 10.1016/S0890-6955(02)00046-9.
18.
RaoS and ShunmugamMS. Analytical modeling of micro end-milling forces with edge radius and material strengthening effects. Mach Sci Technol2012; 16: 205–227. DOI: 10.1080/10910344.2012.673966.
19.
WuX, LiuL, DuM, . Experimental study on the minimum undeformed chip thickness based on effective rake angle in micro milling. Micromachines2020; 11: 924. DOI: 10.3390/mi11100924.
20.
AbdelmoneimME and ScruttonRF. Tool edge roundness and stable build-up formation in finish machining. J Manuf Sci Eng Trans ASME1974; 96: 1258–1267. DOI: 10.1115/1.3438504.
21.
ArmaregoE, BrownRH. The machining of metals. PRENTICE-HALL INC, ENGLEWOOD CLIFFS, N J, 1969, 437 P 1969.
