The advanced machining of components used in miniature unmanned aircraft vehicles is the focus of this study. The finite element method (FEM) is used to predict forces and temperatures using cutting tool inserts with a thin nanostructured film of high integrity. Similarity models are used to validate the finite element results and to understand the influence of micromachining parameters on cutting temperatures generated when machining Al 380-0 alloy. The predicted results are compared to experimental forces and temperatures using a three-dimensional piezoelectric function dynamometer and a short-range infra-red wavelength thermal camera. Nanostructured thin layer coatings lower machining forces and temperatures, which are validated through FEM predictions and experimental observations. The experimental results suggest that increasing the cutting tool’s rake angle at higher depths of cut will reduce cutting temperatures, which are predicted using the similarity models for micromachining.
JacksonMJMorrellJS.Machining with nanomaterials. 2nd ed. Springer Series on ‘Materials Science and Chemistry’. Cham, Switzerland: Springer, 2015, pp. 1–381.
2.
JacksonMJNovakovTda SilvaMBMachadoAR.Predicted chip and non-chip formation when micromachining Ti–6Al–4V titanium alloy. Int J Adv Manuf Technol2017; 91: 955–985.
3.
JacksonMJNovakovTWhitfieldMDRobinsonGMHandyRGSeinHAhmedW.VFCVD diamond coated cutting tools for micromachining titanium alloy Ti–6Al–4V. Int J Adv Manuf Technol2017; 92: 2881–2918.
MarusichTDOrtizM.Modelling and simulation of high speed machining. Int J Num Meth Eng1995: 38: 3675–3694.
6.
SartkulvanichPAltanTGocmenA.Effects of flow stress and friction models in finite element simulation of orthogonal cutting—A sensitivity analysis. Mach Sci Technol2005; 9: 1–26.
7.
BargeMHamdiHRechJBergheauJ-M.Numerical modelling of orthogonal cutting: influence of numerical parameters. J Mater Process Technol2005; 164–165: 1148–1153.
8.
BilHEngin KılıcSErman TekkayaA.A comparison of orthogonal cutting data from experiments with three different finite element models. Inter J Mach Tools Manuf2004; 44: 933–944.
9.
YenYCSöhnerJLillyBAltanT.Estimation of tool wear in orthogonal cutting using the finite element analysis. J Mater Process Technol2004; 146: 82–91.
10.
FangNWuQ.The effects of chamfered and honed tool edge geometry in machining of three aluminium alloys. Inter J Mach Tools Manuf2005; 45: 1178–1187.
11.
GrzesikWBartoszukMNieslonyP.Finite difference method-based simulation of temperature fields for application to orthogonal cutting with coated tools. Mach Sci Technol2005; 9: 529–546.
12.
MacGinleyTMonaghanJ.Modelling the orthogonal machining process using coated cemented carbide cutting tools. J Mater Process Technol2001; 118: 293–300.
13.
OzelT.The influence of friction models on finite element simulations of machining. Inter J Mach Tools Manuf2006; 46: 518–530.
14.
SutterG.Chip geometries during high-speed machining for orthogonal cutting conditions. Inter J Mach Tools Manuf2005; 45, 719–726.
15.
KumberaTGCherukuriHPPattenJABrandJAMarusichTD.Numerical simulations of ductile machining of silicon nitride with a cutting tool of defined geometry. Mach Sci Technol2001; 5(3): 341–352.
16.
MarusichTDAskariE.Modeling residual stress and workpiece quality in machined surfaces. Third Wave Systems, Inc., AdvantEdge, Machining Simulation Software.
KellyJCottrellM.Minimal lubrication machining of aluminium alloys. J Mater Process Technol2002; 120: 327–334.
19.
EzugwuEBonneyJYamaneY.An overview of the machinability of aeroengine alloys. J Mater Process Technol2003; 134: 233–253.
20.
FukuiHOkidaJOmoriNMoriguchiHTsudaK.Cutting performance of DLC coated tools in dry machining aluminium alloys. Surf Coat Technol2004; 187(1): 70–76.
21.
ShenCH.The importance of diamond coated tools for agile manufacturing and dry machining. Surf Coat Technol1996; 86–87(2): 672–677.
22.
JacksonMJAhmedW.Characterization of N-doped polycrystalline diamond films deposited to micro milling tools. J Mater Eng Perfor2005; 14(5): 654–665.
23.
JacksonMJBurgessJ.Microturning of landing gear components used on miniature unmanned aircraft vehicles. J Micromanuf2018; 1: 20–44.
24.
KattusJR.The effect of holding time and strain rate on the tensile properties of structural materials. Proceedings of the Symposium on Short-time High-Temperature Testing, Los Angeles, CA, March 25–29, American Society of Metals, p. 67, 1959.
25.
RosenbergAMRosenbergOA.The state of stress and deformation in metal cutting. Sverhtverdye Materialy1988; 5: 41.
26.
SpaansC.A treatise of the streamlines and the stress, strain and strain rate distributions and on the stability in the primary shear zone in metal cutting. ASME J Eng Ind1972; 94: 690.
27.
ZhangS.Titanium-carbonitride-based cermets: Processes and properties. Mater Sci Eng1993; A163: 141–148.
28.
WangHWebbTBitlerJW.Study of thermal expansion and thermal conductivity of cemented WC–Co composite. Int J Refract Met Hard Mater2015; 49: 170–177.
29.
RobinsonGM.Wear of nanostructured coated cutting tools during mixed scale machining. Ph. D. Thesis, Purdue University, Indiana, USA, 2007.
