Experimental and analytical investigations into wire electrochemical micro turning

Abstract

Electrochemical turning (ECT) has been studied by researchers for making axially symmetric parts of different materials by using shaped tools fed radially into the rotating workpiece. Despite having various advantages over other advanced machining processes, ECT has failed to gain much attention by the manufacturing industries and researchers because of the complexity involved in designing a shaped tool to give a desired shape and tolerances to the workpiece. In the present work, a systematic study is presented to understand the applicability of a microwire as a replacement for a shaped tool in this process. Simulations are carried out to understand the distribution of electric field lines and current density in case of wire electrochemical turning (ECT). The effects of insulting wire up to different angles on the evolved groove profile are investigated by performing simulation study. Minimum groove width is observed at the lowest value of ‘tool exposed angle’ (30°), while maximum groove depth is observed at the highest value of tool exposed angle (270°). In the later part of the work, an experimental study is performed to characterize a groove profile using a bare copper wire of diameter 200 µm. The effects of input parameters, such as workpiece rpm, tool radial insertion, applied potential and electrolyte concentration on responses like groove width, corner radius and taper angle are investigated. Finally, the understanding of behaviour of different process parameters is applied to perform operations like multi-step turning, microgroove turning and taper turning on copper and micro-threading on stainless steel 304.

Keywords

Insulation angle multi-step turning electrochemical micro turning groove width

Get full access to this article

View all access options for this article.

References

Jain

VK.

Advanced machining processes . New Delhi: Allied Publisher, 2002.

Saxena

Qian

Reynaerts

A review on process capabilites of electrochemical micromachining and its hybrid variants (accepted). Int J Mach Tools Manuf; 127: 28–56, https://doi.org/10.1016/j.ijmachtools.2018.01.004 (2018). Accessed October 21, 2018.

Singh

Jain

Kumar

. Machining piezoelectric (PZT) ceramics using an electrochemical spark machining (ECSM) process. J Mater Process Technol 1996; 58: 24–31.

Jain

Dixit

Pandey

PM.

On the analysis of the electrochemical spark machining process. Int J Mach Tools Manuf 1999; 39: 165–186.

Wang

. Pulse electrochemical finishing: modeling and experiment. J Mater Process Technol 2010; 210: 852–857.

Xiaolong

Xindi

Wei

. Electrochemical drilling of multiple small holes with optimized electrolyte dividing manifolds. J Mater Process Technol; 247: 40–47, http://dx.doi.org/10.1016/j.jmatprotec.2017.04.013 (2017). Accessed March 3, 2018.

Ebeid

El-Taweel

TA.

Surface improvement through hybridization of electrochemical turning and roller burnishing based on the Taguchi technique. Proc Inst Mech Eng Part B J Eng Manuf 2005; 219: 423–430.

Hocheng

PS.

Electropolishing of cylindrical workpiece of tool materials using disc-form electrodes. J Mater Process Technol 2003; 142: 203–212.

El-Taweel

Gouda

SA.

Performance analysis of wire electrochemical turning process-RSM approach. Int J Adv Manuf Technol 2011; 53: 181–190.

10.

El-Taweel

Gouda

SA.

Study on the wire electrochemical groove turning process. J Appl Electrochem 2011; 41: 161–171.

11.

Xiangyang

Xiaolong

Yongbin

. Fabrication of micro annular grooves on a cylindrical surface in aluminum alloys by wire electrochemical micromachining. Int J Electrochem Sci 2016; 11: 7216–7229.

12.

Patel

Jain

Shrivastava

. Electrochemical micro texturing on flat and curved surfaces: simulation and experiments. Int J Adv Manuf Technol 2016; 100: 1269–1286.

13.

Haridy

Gouda

An integrated framework of statistical process control and design of experiments for optimizing wire electrochemical turning process. Int J Adv Manuf Technol 2011; 53: 191–207.

14.

Kun

ZHU

Ningsong

QU.

Basic research of wire electrochemical micro-machining. In: International technology and innovation innovation conference , Hangzhou, China, 2006, pp. 1070–1074.

15.

Zhu

Wang

NS.

Micro wire electrochemical cutting by using in situ fabricated wire electrode. CIRP Ann-Manuf Technol 2007; 56: 241–244.

16.

Shin

Kim

Chu

CN.

Analysis of the side gap resulting from micro electrochemical machining with a tungsten wire and ultrashort voltage pulses. J Micromech Microeng 2008; 18: 075009.

17.

Zeng

YB.

Wire electrochemical machining using reciprocated traveling wire. Int J Adv Manuf Technol 2014; 72: 677–683.

18.

Zeng

Yao

. Improving machining efficiency in wire electrochemical micromachining of array microstructures using axial vibration-assisted multi-wire electrodes. J Manuf Process; 25: 452–460, http://dx.doi.org/10.1016/j.jmapro.2017.01.004 (2017). Accessed June 14, 2018.

19.

Zeng

Wang

al.

Enhancement of mass transport in micro wire electrochemical machining. CIRP Ann-Manuf Technol 2012; 61: 195–198.

20.

Wang

Zeng

Liu

. Micro wire electrochemical machining with an axial electrolyte flow. Int J Adv Manuf Technol 2012; 63: 25–32.

21.

Jain

Chouksey

AK.

A comprehensive analysis of three-phase electrolyte conductivity during electrochemical macromachining/micromachining. Proc Inst Mech Eng Part B J Eng Manuf 2018; 232: 2449–2461.

22.

Tyagi

Sharma

Jain

. Investigations into side gap in wire electrochemical micromachining (wire-ECMM). Int J Adv Manuf Technol 2017; 94: 4469-4478.

23.

Patel

Jain

Ramkumar

Micro texturing on metallic surfaces: state of the art. Proc Inst Mech Eng Part B J Eng Manuf , http://pib.sagepub.com/lookup/doi/10.1177/0954405416661583 (2016). Accessed March 5, 2018.

24.

Martin

Hackert-Oschätzchen

Schubert

Design and realisation of a specific device for jet electrochemical machining of rotating workpieces. In J. Deconinck (Ed.): Proceedings of the 12th International symposium on electrochemical machining technology , Brussel: University press, 2016, p. 39.

25.

Tosun

Cogun

Tosun

A study on kerf and material removal rate in wire electrical discharge machining based on Taguchi method. J Mater Process Technol; 152: 316–322, http://ac.els-cdn.com/S0924013604007496/1-s2.0-S0924013604007496-main.pdf?_tid=8fe8c390-67a1-11e7-adf2-00000aacb361&acdnat=1499933106_a9b647dbc9a9283050813fc9fae63788 (2004, accessed 13 July 2017).

26.

Sharma

Srivastava

Tyagi

al.

Theoretical and experimental investigations into wire electrochemical turning (wire-ECTrg) process using finite element method. J Electrochem Soc 2018; 165: 773–783.

27.

Wang

Zhu

. Reduction of stray currents in counter-rotating electrochemical machining by using a flexible auxiliary electrode mechanism. J Mater Process Technol; 239: 66–74, http://linkinghub.elsevier.com/retrieve/pii/S0924013616302771 (2017).