Influence of variability in hygrothermal properties on analytical results of simultaneous heat and moisture transfer in porous materials

Abstract

Depending on the data source used, the material hygrothermal properties that are used in the numerical analysis of simultaneous heat and moisture transfer will not be consistent. Differences in measurement methods and the individuality of specimens account for this. It is necessary to choose values from these different physical property sets to conduct a numerical calculation, which can cause the calculated results to differ. The subsequent range of variation in the calculated results should be quantitatively evaluated. In this study, the physical properties of several types of porous building materials were first gathered from four databases. The data were then categorized based on the kind of material and compared in terms of each physical property (density, porosity, specific heat, moisture capacity, thermal conductivity, and vapor permeability). The density, porosity, and specific heat varied by 10% on average, and the moisture capacity, thermal conductivity, and vapor permeability varied by 20% or more for all types of materials. In particular, the vapor permeability of plywood and moisture capacity of gypsum board differed by 50%. The influence that these physical property value variations had on hygrothermal calculation results was then quantitatively demonstrated for moisture and heat flow rate under a step change in the relative humidity or temperature of indoor air for a single layer wall. The moisture and heat flow rate into a single layer wall fluctuated by approximately 10%–40% due to differences in the vapor permeability and moisture capacity of the materials. For all types of materials, moisture was transferred more slowly than heat. Therefore, differences in moisture property values, such as vapor permeability and moisture capacity, influenced the results more significantly. Moreover, the moisture flow was accompanied by a phase change. The differences in moisture property values thus affected the heat flow.

Keywords

Hygrothermal properties simultaneous heat and moisture transfer numerical analysis variability database porous material air conditioning load

Get full access to this article

View all access options for this article.

References

ASHRAE (2013) Chapter 26: Heat, air, and moisture control in building assemblies—material properties. In: ASHRAE (ed.) ASHRAE Handbook of Fundamentals. Atlanta, GA: ASHRAE, pp.26.2–26.20.

Barclay

Holcroft

Shea

(2014) Methods to determine whole building hygrothermal performance of hemp–lime buildings. Building and Environment 80: 204–212.

Defraeye

Blocken

Carmeliet

(2013) Influence of uncertainty in heat–moisture transport properties on convective drying of porous materials by numerical modelling. Chemical Engineering Research and Design 91: 36–42.

Feng

Guimarães

Ramos

, et al. (2020) Hygric properties of porous building materials (VI): A round robin campaign. Building and Environment 185: 107242.

Feng

Janssen

(2016) Hygric properties of porous building materials (II): Analysis of temperature influence. Building and Environment 99: 107–118.

Feng

Janssen

Feng

, et al. (2015) Hygric properties of porous building materials: Analysis of measurement repeatability and reproducibility. Building and Environment 85: 160–172.

Feng

Janssen

, et al. (2013) Validating various measures to accelerate the static gravimetric sorption isotherm determination. Building and Environment 69: 64–71.

Fraunhofer Institute for Building Physics (2018) WUFI. Available at: http://wufi.de/en/ (accessed 12 January 2021).

Fridman

(ed.) (2012) Chapter 8 assurance of measurement accuracy in compliance with ISO 5725 standards. In: The Quality of Measurements: A Metrological Reference. New York, NY: Springer, pp.179–195.

10.

Hens

HSLC

Mukhopadhyaya

Kumaran

, et al. (2007) Modeling the heat, air, and moisture response of building envelopes: What material properties are needed, how trustful are the predictions? Journal of ASTM International 4: 1–11.

11.

Janssen

(2013) Monte-Carlo based uncertainty analysis: Sampling efficiency and sampling convergence. Reliability Engineering & System Safety 109: 123–132.

12.

Janssen

Blocken

Roels

, et al. (2007) Wind-driven rain as a boundary condition for HAM simulations: Analysis of simplified modelling approaches. Building and Environment 42: 1555–1567.

13.

Kumaran

(1996) Heat, air and moisture transfer through new and retrofitted insulated envelope parts. Final report volume 3 task 3: Material properties. IEA Annex 24 Hamtie.

14.

Kumaran

(2002) A thermal and moisture transport property database for common building and insulating materials. Final report from ASHRAE Research Project 1018-RP. Ottawa: National Research Council, Canada.

15.

Kumaran

Lackey

Normandin

, et al. (2002) Summary Report From Task 3 of MEWS Project at the Institute for Research in Construction – Hygrothermal Properties of Several Building Materials. IRC-RR-110. Ottawa: National Research Council Canada.

16.

Kunzel

(1995) Simultaneous Heat and Moisture Transport in Building Components—One-and Two-Dimensional Calculation Using Simple Parameters. Stuttgart: IRB Verlag.

17.

Matsumoto

(1978) Simultaneous heat and moisture transfer in porous wall and analysis of internal condensation. In: Hoogendoorn

Afgan

(eds) Energy Conservation in Heating, Cooling, and Ventilating Buildings, vol. 1. Washington: Hemisphere Publishing Corporation. pp.45–58.

18.

Nishimura

Kominami

Kobayakawa

(2004) An estimation of the uncertainty of measurement on thermal insulation test. Journal of Environmental Engineering, Architectural Institute of Japan 584(17): 23. (in Japanese, with English abstract).

19.

Pietrak

Kubiś

Cieślikiewicz , et al. (2019) Measurement of thermal, hygric and physical properties of bricks and mortar common for the Polish market. IOP Conference Series Materials Science and Engineering660: 012022.

20.

Prada

Cappelletti

Baggio

, et al. (2014) On the effect of material uncertainties in envelope heat transfer simulations. Energy and Buildings 71: 53–60.

21.

Roels

(2008) Whole building heat, air and moisture response, Subtask 2: Experimental analysis of moisture buffering, IEA ANNEX 41.

22.

Roels

Carmeliet

Hens

, et al. (2003) Moisture transfer properties and materials characterisation. HAMSTAD work package 1 final report. K. U. Leuven, Leuven.

23.

Roels

Carmeliet

Hens

, et al. (2004) Interlaboratory comparison of hygric properties of porous building materials. Journal of Thermal Envelope and Building Science 27: 307–325.

24.

Wilrich

(2010) The determination of precision of qualitative measurement methods by interlaboratory experiments. Accreditation and Quality Assurance 15: 439–444.

25.

Bažant

Molina

, et al. (1994) Moisture diffusion in cementitious materials moisture capacity and diffusivity. Advanced Cement Based Materials 1: 258–266.