Implementation of rainwater infiltration measurements in hygrothermal modelling of non-insulated brick cavity walls

Abstract

The watertightness of solid masonry walls is generally based on the concept of buffering and afterwards drying out the absorbed rainwater. In cavity walls, on the contrary, the air layer provides a capillary break between the inner and outer leafs allowing drainage of rainwater and preventing infiltration to the interior wall surface. For assessing moisture-related risks, heat, air and moisture models have proven to be a valuable tool, but in the case of cavity walls two problems arise: the degree of water infiltration into the cavity is unknown, and no consensus is available on the method that should be used to implement these infiltrations in a simulation. For example, for the existing buildings, it is worthwhile to investigate whether injecting cavity wall insulation induces an increase or decrease in moisture-related pathologies, in contrast to adopting a fixed performance criterion for assessment. However, to complete a thorough analysis of a brick cavity wall, it is first useful to review the hygrothermal behaviour of cavity walls as it has been previously described in the literature. As such, this article provides a summary of experimental water infiltration results for cavity walls as described in the literature, discusses experimental results of four test walls subjected to four test protocols and extracts from these results the water infiltration rate for implementation in heat, air and moisture models. Finally, several methods for implementing the infiltrations in heat, air and moisture simulations are presented and evaluated based on different damage criteria. In general, the new modelling approaches are considered to provide realistic results. Nonetheless, an in situ investigation on whether mortar bridges occur in the cavity due to poor workmanship remains crucial to understanding the hygrothermal response as mortar bridges are found to have a dominant impact on the risk of mould growth at the interior wall surface.

Keywords

Brick masonry rain water infiltration heat air and moisture moisture sources cavity walls ASHRAE 160

Get full access to this article

View all access options for this article.

References

ASHRAE 160 (2016) Criteria for moisture-control design analysis in buildings.

ASTM C1715-10 (2010) Standard test method for evaluation of water leakage performance of masonry wall drainage systems.

ASTM E514-02 (2009) Standard test method for water penetration and leakage through masonry.

Blocken

Carmeliet

(2004) A simplified approach for quantifying driving rain on buildings. In: Proceedings of the 9th international conference performance of exterior envelopes of whole buildings IX, Clearwater, FL, 5–10 December, pp. 1–12. Available at: https://research.tue.nl/en/publications/a-simplified-approach-for-quantifying-driving-rain-on-buildings

Brown

(1982) Initial effects of clear coatings on water permeance of masonry. In Borchelt

(ed.) ASTM STP 778. West Conshohocken, PA: American Society for Testing and Materials, pp. 221–236.

Calle

Van Den Bossche

(2017) Analysis of different frost indexes and their potential to assess frost based on HAM simulations. In De Schutter

, et al. (eds) Proceedings of the 14th international conference on durability of buildings materials and components (eds. De Schutter

Geert

Janssens

Arnold

De Belie

Nele

Van Den Bossche

Nathan

). Ghent: RILEM, pp. 61–64.

Carbonez

Van Den Bossche

Janssens

(2015) Comparison between uniform rain loads and point sources to simulate rainwater leakage with commercial HAM-models. In: ISBP2015 proceedings, pp. 105–112. Available at: https://biblio.ugent.be/publication/6843090/file/6843108.pdf

Chiovitti

Gonçalves

Renzullo

(1999) Performance evaluation of water repellents for above grade masonry. In: (eds Lacasse

Vanier

) Durability of Building Materials and Components 8. Ottawa, ON, Canada: Institute for Research in Construction, pp. 561–570.

EN 1991-1-4:2005+A1 (2010) Eurocode 1: actions on structures – part 1-4: general actions – wind actions.

10.

EN ISO 13788 (2001) Hygrothermal performance of building components and building elements – internal surface temperature to avoid critical surface humidity and interstitial condensation – calculation methods.

11.

Ghosh

Melander

(1991) Air Content of Mortar and Water Penetration of Masonry Walls. Skokie, IL: Portland Cement Association.

12.

Grunewald

(1996) Diffusiver und konvektiver Stoff- und Energietransport in kapillarporösen Baustoffen. Doctoral dissertation at the faculty of Engineering at TU Dresden in 1996. ISBN: 3860051911.

13.

Grunewald

Häupl

Bomberg

(2003) Towards an engineering model of material characteristics for input to ham transport simulations – part 1: an approach. Journal of Building Physics 26(4): 343–366.

14.

Hens

Roels

Desadeleer

(2004) Rain leakage through veneer walls, built with concrete blocks. In: Proceedings of the international council for research and innovation in building and construction (CIB W40 Meeting), Glasgow, 31 August–3 September, p. 10. Available at: https://limo.libis.be/primo-explore/fulldisplay?docid=LIRIAS1728907&context=L&vid=Lirias&search_scope=Lirias&tab=default_tab&lang=en_US&fromSitemap=1

15.

Janssen

Blocken

Carmeliet

(2007) Conservative modelling of the moisture and heat transfer in building components under atmospheric excitation. International Journal of Heat and Mass Transfer 50(5–6): 1128–1140.

16.

Janssens

Van Londersele

Vandermarcke

, et al. (2007) Development of Limits for the Linear Thermal Transmittance of Thermal Bridges in Buildings. Atlanta, GA: ASHRAE.

17.

Lacasse

O’Connor

Nunes

, et al. (2003) Report from task 6 of MEWS project: experimental assessment of water penetration and entry into wood-frame wall specimens – final report. Available at: https://nrc-publications.canada.ca/eng/view/object/?id=a77069ab-cc34-4c51-906b-6e07170b692e

18.

Langmans

Desta

Alderweireldt

, et al. (2016) Field study on the air change rate behind residential rainscreen cladding systems: a parameter analysis. Building and Environment 95: 1–12.

19.

Meert

, Belgium Building Research Institute (2000) The Flat Roof: Assembly, Materials, Execution, Maintenance. Brussels (in Dutch): (Technische Voorlichtingsnota 215).

20.

NBN EN 12865 (2001) Hygrothermal performance of building components and building elements – determination of the resistance of external wall systems to driving rain under pulsating air pressure.

21.

NEN 2778 (2004) Moisture control in buildings (in Dutch).

22.

Ojanen

Peuhkuri

Viitanen

, et al. (2011) Classification of material sensitivity – new approach for mould growth modeling. In: Vinha

Piironen

Salminen

(eds) Proceedings of the 9th Nordic Symposium on Building Physics, vol. 2. Tampere: Tampere University of Technology, pp. 867–874.

23.

Rathbone

(1982) Rain and air penetration performance of concrete blockwork. Technical Report No. 553. South Yarra, VIC, Australia: Cement and Concrete Association.

24.

Salonvaara

Karagiozis

(1998) The influence of waterproof coating on the hygrothermal performance of a brick façade wall system. In: Kudder

Erdly

(eds) Water Leakage through Building Facades. West Conshohocken, PA: American Society for Testing and Materials, pp. 295–311.

25.

Straube

Schumacher

Mensinga

(2010) Assessing the freeze-thaw resistance of clay brick for interior insulation retrofit projects. In: Proceedings of the performances of envelopes of whole buildings XI, 15 December, pp. 1–8. Available at: https://buildingscience.com/sites/default/files/migrate/pdf/CP-1013_Assessing_Freeze_Thaw_Resistance_Clay_Brick_Insulation_Retrofit.pdf

26.

Van Belleghem

Steeman

Janssens

, et al. (2015) Heat, air and moisture transport modelling in ventilated cavity walls. Journal of Building Physics 38: 317–349.

27.

Van Den Bossche

(2013) Watertightness of Building Components: Principels, Testing and Design Guidlines. Doctoral dissertation at the faculty of engineering and architecture at Ghent University in 2013. ISBN: 978-90-8578-570-5.

28.

Van Den Bossche

Lacasse

Janssens

(2011) Watertightness of masonry walls: an overview. In: Proceedings of the 12th international conference on durability of building materials and components, Porto, pp. 1–11. Available at: https://nrc-publications.canada.ca/eng/view/accepted/?id=fe3d9bdc-e61a-405e-9527-c37974f9f79b

29.

Van Den Bossche

Lacasse

Janssens

(2013a) A uniform methodology to establish test parameters for watertightness testing: part I: a critical review. Building and Environment 63: 145–156.

30.

Van Den Bossche

Lacasse

Janssens

(2013b) A uniform methodology to establish test parameters for watertightness testing part II: pareto front analysis on co-occurring rain and wind. Building and Environment 63: 157–167.

31.

Vereecken

Van Gelder

Janssen

, et al. (2015) Interior insulation for wall retrofitting – a probabilistic analysis of energy savings and hygrothermal risks. Energy and Buildings 89: 231–244.

32.

Viitanen

Ojanen

(2007) Improved model to predict mold growth in building materials. Available at: https://web.ornl.gov/sci/buildings/conf-archive/2007%20B10%20papers/162_Viitanen.pdf

33.

Viitanen

Vinha

Salminen

, et al. (2010) Moisture and bio-deterioration risk of building materials and structures. Journal of Building Physics 33(3): 201–224.

34.

Vos

Tammes

(1976). Rain Penetration Through the Outer Walls of Cavity Structures, Paper Presented at the CIB-W40 Meeting, Washington.