Absolute stress measurement of structural steel members with ultrasonic shear-wave spectral analysis method

Abstract

Absolute stress in structural steel members is an important parameter for the design, construction, and servicing of steel structures. However, it is difficult to measure via traditional approaches to structural health monitoring. The ultrasonic time-of-flight method has been widely studied for monitoring absolute stress by measuring the change in ultrasonic propagation time induced by stress. The time-of-flight of the two separated shear-wave modes induced by birefringence, which is particular to shear waves, is also affected by stress to different degrees. Their synthesis signal amplitude spectrum exhibits a minimum that varies with stress, which makes it a potential approach to evaluating uniaxial stress using the shear-wave amplitude spectrum. In this study, the effect of steel-member stress on the shear-wave amplitude spectrum from the interference of two shear waves produced by birefringence is investigated, and a method of uniaxial absolute stress measurement using shear-wave spectral analysis is proposed. Specifically, a theoretical expression is derived for the shear-wave pulse-echo amplitude spectrum, leading to a formula for evaluating uniaxial absolute stress. Three steel-member specimens are employed to investigate the influence of uniaxial stress on the shear-wave pulse-echo amplitude spectrum. The testing results indicate that the amplitude spectrum changes with stress and that the inverse of the first characteristic frequency in the amplitude spectrum and its corresponding stress exhibit a near-perfect linear relationship. On this basis, the uniaxial absolute stress of steel members loaded by a test machine is measured by the proposed method. Parametric studies are further performed on three groups of steel members made of 65# steel and Q235 steel to investigate the factors that influence the testing results. The results show that the proposed method can measure and monitor steel-members uniaxial absolute stress on the laboratory scale and has potential to be used in practical engineering with specific calibration.

Keywords

Uniaxial absolute stress monitoring structural steel members shear-wave birefringence amplitude spectrum acoustoelastic effect

Get full access to this article

View all access options for this article.

References

Rossini

Dassisti

Benyounis

et al . Methods of measuring residual stresses in components. Mater Design 2012; 35: 572–588.

Guan

Duan

et al . Guided waves for damage identification in pipeline structures: a review. Struct Control Hlth 2017; 24(11): e2007.

Crack identification in aluminium plates using Lamb wave signals of a PZT sensor network. Smart Mater Struct 2006; 15(3): 839.

Hao

Fan

et al . Development and application of a relative displacement sensor for structural health monitoring of composite bridges. Struct Control Hlth 2015; 22(4): 726–742.

CT.

Bayesian model updating approach for experimental identification of damage in beams using guided waves. Struct Health Monit 2014; 13(4): 359–373.

Domaneschi

Martinelli

Control of wind buffeting vibrations in a suspension bridge by TMD: hybridization and robustness issues. Comput Struct 2015; 155: 3–17.

Teng

Wen

et al . Instrumentation on structural health monitoring systems to real world structures. Smart Struct Syst 2015; 15(1): 151–167.

Yang

Nie

Kang

et al . Residual stress measurement on welded Q345GJ steel H-sections by sectioning method and method improvement. Adv Steel Constr 2017; 13(1): 78–95.

Woo

Truman

et al . Two-dimensional mapping of residual stresses in a thick dissimilar weld using contour method, deep hole drilling, and neutron diffraction. J Mater Sci 2016; 51(23): 10620–10631.

10.

Lin

Lei

et al . Measurement of residual stress in arc welded lap joints by cos alpha X-ray diffraction method. J Mater Process Tech 2017; 243: 387–394.

11.

Woo

et al . Through-thickness distributions of residual stresses in an 80 mm thick weld using neutron diffraction and contour method. J Mater Sci 2015; 50(2): 784–793.

12.

Gur

Erian

Batigun

et al . Investigating the effects of subsequent weld passes on surface residual stresses in steel weldments by magnetic Barkhausen noise technique. Mater Eval 2016; 74(3): 418–423.

13.

Teng

et al . Internal stress monitoring of in-service structural steel members with ultrasonic method. Materials 2016; 9(4): 223.

14.

Crecraft

DI.

The measurement of applied and residual stresses in metals using ultrasonic waves. J Sound Vib 1967; 5(1): 173–192.

15.

Buenos

Dos Santos

Jr Rodrigues

et al . Application of acoustoelasticity to measure the stress generated by milling in ASTM A36 steel plates. J Braz Soc Mech Sci 2013; 35(4): 525–536.

16.

Jhang

Quan

et al . Estimation of clamping force in high-tension bolts through ultrasonic velocity measurement. Ultrasonics 2006; 44(8): e1339–e1342.

17.

Karabutov

Devichensky

Ivochkin

et al . Laser ultrasonic diagnostics of residual stress. Ultrasonics 2008; 48(6): 631–635.

18.

Vangi

Stress evaluation by pulse-echo ultrasonic longitudinal wave. Exp Mech 2001; 41(3): 277–281.

19.

Link

Vangi

Ultrasonic technique for experimental evaluation of structural integrity. J Test Eval 2001; 29(3): 301–305.

20.

Schramm

RE.

Ultrasonic measurement of stress in railroad wheels. Rev Sci Instrum 1999; 70(2): 1468–1472.

21.

Clark

Moulder

JC.

Residual stress determination in aluminium using electromagnetic acoustic transducers. Ultrasonics 1985; 23(6): 253–259.

22.

Allen

Sayers

CM.

The measurement of residual stress in textured steel using an ultrasonic velocity combinations technique. Ultrasonics 1984; 22(4): 179–188.

23.

Javadi

Azari

Ghalehbandi

et al . Comparison between using longitudinal and shear waves in ultrasonic stress measurement to investigate the effect of post-weld heat-treatment on welding residual stresses. Res Nondestruct Eval 2017; 28(2): 101–122.

24.

Bray

Junghans

Application of the L_CR ultrasonic technique for evaluation of post-weld heat treatment in steel plates. NDT&E Int 1995; 28(4): 235–242.

25.

Dos Santos

Bray

. Comparison of acoustoelastic methods to evaluate stresses in steel plates and bars. J Press Vess: T ASME 2002; 124(3): 354–358.

26.

Chaki

Demouveau

Numerical and experimental analysis of the critically refracted longitudinal beam. Ultrasonics 2013; 53(1): 65–69.

27.

Javadi

Mosteshary

SH.

Evaluation of sub-surface residual stress by ultrasonic method and finite-element analysis of welding process in a monel pressure vessel. J Test Eval 2017; 45(2): 441–451.

28.

Sgalla

Vangi

UCRfr—ultrasonic critical-angle refractometry for stress measurement. Nondestruct Test Eva 2003; 19(1–2): 67–77.

29.

Mohabuth

Kotousov

CT.

Effect of uniaxial stress on the propagation of higher-order Lamb wave modes. Int J Nonlin Mech 2016; 86: 104–111.

30.

Duquennoy

Ouaftouh

Ourak

Ultrasonic evaluation of stresses in orthotropic materials using Rayleigh waves. NDT&E Int 1999; 32(4): 189–199.

31.

Wali

Njeh

Wieder

et al . The effect of depth-dependent residual stresses on the propagation of surface acoustic waves in thin Ag films on Si. NDT&E Int 2007; 40(7): 545–551.

32.

Palanichamy

Joseph

Jayakumar

et al . Ultrasonic velocity measurements for estimation of grain size in austenitic stainless steel. NDT&E Int 1995; 28(3): 179–185.

33.

Javadi

Akhlaghi

Najafabadi

MA.

Nondestructive evaluation of welding residual stresses in austenitic stainless steel plates. Res Nondestruct Eval 2014; 25(1): 30–43.

34.

Lhemery

Calmon

Chatillon

et al . Modeling of ultrasonic fields radiated by contact transducer in a component of irregular surface. Ultrasonics 2002; 40(1): 231–236.

35.

Aindow

Chivers

RC.

The optimization of electronic precision in ultrasonic velocity measurements: a comparison of the time interval averaging and sing around methods. J Acoust Soc Am 1983; 73(5): 1833.

36.

Badidi Bouda

Lebaili

Benchaala

. Grain size influence on ultrasonic velocities and attenuation. NDT&E Int 2003; 36(1): 1–5.

37.

Vangi

Virga

A practical application of ultrasonic thermal stress monitoring in continuous welded rails. Exp Mech 2007; 47(5): 617–623.

38.

Lipeles

Kivelson

Theory of ultrasonically induced birefringence. J Chem Phys 1977; 67(10): 4564–4570.

39.

Blinka

Sachse

Application of ultrasonic-pulse-spectroscopy measurements to experimental stress analysis. Exp Mech 1976; 16(12): 448–453.

40.

Song

Pan

et al . Nondestructive testing and characterization of residual stress field using an ultrasonic method. Chin J Mech Eng: En 2016; 29(2): 365–371.

41.

Hauk

Structural and residual stress analysis by nondestructive methods. Amsterdam: Elsevier, Ltd, 1997.

42.

People’s Republic of China National Standard GB 50755-2012:2012. Code for construction of steel structures (China Standard Press, 2012).

43.

People’s Republic of China National Standard GB/T 699-2015:2015. Quality carbon structure steels (China Standard Press, 2015).