Damage Identification of Metallic Structures Using A 0 Mode of Lamb Waves

Abstract

A Lamb wave-based technique was developed for detecting damages in metallic structures, such as cracks and holes in metallic beams and plates. For metallic structures with transverse cracks and holes, A₀ mode of Lamb waves was employed due to its shorter wave length compared with S₀ mode, which leads to high sensitivity to small damages. Two kinds of excitation techniques for generating comparatively pure A₀ mode using piezoelectric lead zirconate titanate (PZT) actuators were realized experimentally. In one technique, two PZT actuators with applied out-of-phase voltages were attached on both sides of the structures. While in the other technique, a kind of grease lubricant was used between the bottom surface of one PZT actuator and the surface of the specimens. Both techniques were able to enhance the component of A₀ mode and reduce the component of S₀ mode effectively. Secondly, in terms of the arrival time of the A₀ wave mode reflected from damages obtained using the wavelet analysis, the positions of damages were identified accurately. The above two techniques were then validated by identifying the transverse cracks and holes in aluminum beams and plates, respectively. Numerical simulations using the finite element method (FEM) for the wave propagation in these structures with damages were carried out. The obtained experimental and numerical results demonstrate that it is possible to identify damage position very accurately by using only sensor data of defective structures without referring benchmark signals (sensor data of intact structures).

Keywords

Lamb wave A0 mode metallic structures damage identification FEM

Get full access to this article

View all access options for this article.

References

Su, Z.Q. , Ye, L. and Lu, Y. (2006). Guided Lamb waves for identification of damage in composite structures: A review . Journal of Sound & Vibration, 295(3-5), 753-780.

Valdes, S.H.D. and Soutis, C. (2001). A structural health monitoring system for laminated composites . In: Proceedings of DETC, Pittsburgh, PA, USA.

Sohn, H. and Farrar, C.R. (2001). Damage diagnosis using time series analysis of bivration signals . Smart Materials and Structures, 10, 1-6.

Ihn, J.B. and Chang, F.-K. (2001). Built-in diagnostics for monitoring crack growth in aircraft structures. In: Chang, F.-K. (ed.), Proceedings of the international workshop on structural health monitoring, Stanford University , USA.

Hurlesbaus, S. , Niethammer, M. , Jacobs, L.J. and Valle, C. (2001). Automated methodology to locate notches with Lamb waves . Acoustics Research Letters Online, 2, 97-102.

Bork, U. and Challis, R.E. (1994). Artificial neural networks applied to Lamb wave testing of T-form adhered joints. In: Saffari, N. (ed.), Proceedings of the Conference on the Inspection of Structural Composites, Bentham Press, London, UK.

Su, Z. and Ye, L. (2004). Lamb wave propagation-based damage identification for quasi-isotropic CF/EP composite laminates using artificial neural algorithm, Part-I: methodology and database development . Journal of Intelligent Material Systems and Structures, 16, 97-111.

Zang, C. , Friswell, M.I. and Imregun, M. (2004). Structural damage detection using independent component analysis . Structural Health Monitoring: An International Journal. 3(1), 69-83.

Lemistre, M. and Balageas, D.L. (2001). Structural health monitoring system based on diffracted Lamb wave analysis by multiresolution processing . Smart Materials and Structures, 10, 504-511.

10.

Roh, Y.S. and Chang, F.-K. (1995). Effect of impact damage on Lamb wave propagation in laminated composites . In: Proceedings of ASME on Dynamic Responses and Behavior of Composites, USA.

11.

Monkhouse, R.S.C. , Wilcox, P.W. , Lowe, M.J.S. , Dalton, R.P. and Cawley, P. (2000). The rapid monitoring of structures using interdigital Lamb wave transducer . Smart Materials and Structures, 9, 304-309.

12.

Kessler, S.S. , Spearing, S.M. and Soutis, C. (2002). Damage detection in composite materials using Lamb wave methods . Smart Materials and Structures , 11, 269-278.

13.

Grondel, S. , Paget, C. , Delebarre, C. , Assaad, J. and Levin, K. (2002). Design of optimal configuration for generating A0 Lamb mode in a composite plate using piezoelectric transducers . Journal of the Acoustical Society of America, 112, 84-90.

14.

Su, Z. and Ye, L. (2004). Selective generation of Lamb wave modes and their propagation characteristics in defective composite laminates . Journal of Materials: Design and Applications, 218, 95-110.

15.

Viktorov, I.A. (1976). Rayleigh and Lamb Waves, New York: Plenum press.

16.

Rose, W.R. (1999). Ultrasonic Waves in Solid Media, Cambridge: Cambridge University Press.

17.

Jeong, H. and Jang, Y.S. (2000). Wavelet analysis of plate wave propagation in composite laminates . Composite Structures, 49, 443-450.

18.

Cao, Y.P. , Hu, N. , Lu, J. , Fukunaga, H. and Yao, Z.H. (2002). A 3D brick element based on Hu-Washizu variational principle for mesh distorsion . Int. J. Numer. Meth. Eng., 53, 2529-2548.