The paper presents an integrated tribo-dynamics analysis of elliptic bore overlay big end bearings of internal combustion engines. The analysis focuses on bearing stability, frictional power loss and acoustic emission from these bearings, particularly with cylinder deactivation with larger fluctuations in engine loading. The integrated approach represents a tribo-dynamics analysis, not hitherto reported in literature, particularly under cylinder deactivation. The analysis shows that cylinder deactivation makes marginal differences in parasitic frictional losses in engine bearing performance and any significant gain would depend on the brake specific fuel consumption. It is also shown that sufficient swept volume with retained residual exhaust gas charge within the deactivated cylinders can ensure bearing whirl stability. Partially deactivated engine configurations exhibit a lower average steady noise emission, but with a higher degree of transient content. This suggests that there would be a greater contribution to engine rumble with deactivated cylinders.
TungSCMcMillanML. Automotive tribology overview of current advances and challenges for the future. Tribol Int2004; 37: 517–536.
2.
Falkowski A, McElwee M and Bonne M. Design and development of the DaimlerChrysler 5.7L HEMI® engine multi-displacement cylinder deactivation system. SAE Technical Paper 2004 01-2106, 2004.
3.
Roberts C. Variable valve timing. SwRI Project No. 03.03271, Clean Diesel III Program, March 2004.
4.
WilcuttsMSwitkesJShostM. Design and benefits of dynamic skip fire strategies for cylinder deactivated engines. SAE Int J Engines2013; 6: 278–288.
5.
Rahnejat H. Multi-body dynamics: Vehicles, machines and mechanisms. Professional Engineering Publishing (UK) and SAE (USA), 1998.
6.
Senapati U, McDevitt I and Hankinson A. Vehicle refinement challenges for a large displacement engine with cylinder deactivation capability. SAE technical paper 2011-01-1678, 2011.
KushwahaMGuptaSKellyP. Elasto-multi-body dynamics of a multicylinder internal combustion engine. Proc IMechE Part K: J Multi-body Dynamics2002; 216: 281–293.
9.
MendayMTRahnejatHEbrahimiM. Clonk: An onomatopoeic response in torsional impact of automotive drivelines. Proc IMechE Part D: J Automobile Engineering1999; 213: 349–357.
10.
GoharRRahnejatH. Fundamentals of tribology, London: Imperial College Press, 2008.
11.
MishraPCRahnejatHTribology of big end bearings. In: RahnejatH (eds). Tribology and dynamics of engine and power train, Cambridge, UK: Woodhead Publishing, 2010.
12.
BatesTWFantinoBLaunayL. Oil film thickness in an elastic connecting-rod bearing: Comparison between theory and experiment. Tribol Trans1990; 33: 254–266.
AitkenMBMcCallionH. Elastohydrodynamic lubrication of big-end bearings. Part 1: Theory. Proc IMechE Part C: J Mechanical Engineering Science1991; 205: 99–106.
15.
AitkenMBMcCallionH. Elastohydrodynamic lubrication of big-end bearings. Part 2: Ratification. Proc IMechE Part C: J Mechanical Engineering Science1991; 205: 107–119.
16.
Balakrishnan S, McMinn C, Baker CE, et al. Fundamentals of crank and camshaft support journal bearings. In: Rahnejat H (ed.) Tribology and dynamics of engine and powertrain. Cambridge, UK: Woodhead Publishing, 2010.
17.
BoedoSBookerJF. Finite element analysis of elastic engine bearing lubrication: Application. Rev Européenne Elém Finis2001; 10: 725–740.
18.
BonneauDGuinesDFreneJ. EHD analysis, including structural inertia effects and a mass-conserving cavitation model. Trans ASME J Tribol1995; 117: 540–547.
19.
RahnejatH. Multi-body dynamics: Historical evolution and application. Proc IMechE Part C: J Mechanical Engineering Science2000; 214: 149–173.
20.
MajumdarBC. The effect of roughness parameter on the performance of hydrodynamic journal bearings with rough surfaces. Tribol Int1999; 32: 231–236.
21.
KimB-JKimK-W. Thermo-elastohydrodynamic analysis of connecting rod bearing in internal combustion engine. Trans ASME J Tribol2001; 123: 444–454.
22.
StefaniFARebornAU. Finite element analysis of dynamically loaded journal bearings: Influence of the bolt preload. Trans ASME J Tribol2002; 124: 486–493.
23.
CrosbyWA. Thermal considerations in the solution of finite journal bearings. Wear1980; 64: 15–32.
24.
BoncompainRFillonMFreneJ. Analysis of thermal effects in hydrodynamic bearings. Trans ASME J Tribol1986; 108: 219–224.
25.
ThomsonWT. Vibration theory and applications, 5th ed. Guildford, Surrey, UK: Prentice Hall Inc, 1976.
26.
GreenwoodJATrippJH. The contact of two nominally flat rough surfaces. Proc Instn Mech Engrs1970–1971; 185: 625–633.
27.
TeodorescuMBalakrishnanSRahnejatH. Integrated tribological analysis within a multi-physics approach to system dynamics. Tribol Interface Eng Ser2005; 48: 725–737.
28.
MohammadpourMTheodossiadesSRahnejatH. Elastohydrodynamic lubrication of hypoid gears at high load. Proc IMechE Part J: J Engineering Tribology2012; 226: 183–198.
29.
ElrodHG. A cavitation algorithm. Trans ASME J Lubr Technol1981; 103: 350–354.
30.
MorrisNRahmaniRRahnejatH. Tribology of piston compression ring conjunction under transient thermal mixed regime of lubrication. Tribology Int2013; 59: 248–258.
31.
ShigleyJEUickerJJ Jr. Theory of machines and mechanisms, New York: McGraw-Hill, 1995.
32.
SuryanarayanaNVForced convection internal flows. In: KreithF (eds). The handbook of thermal engineering, Boca Raton: CRC Press, 2000, pp. 47–55.
33.
CarslawHSJaegerJC. Conduction of heat in solids, 2nd ed. Oxford: Science Publications, 2005.
34.
Chong WWF, Teodorescu M and Rahnejat H. Nanoscale elastoplastic adhesion of wet asperities. Proc IMechE Part J: J Engineering Tribology. DOI: 10.1177/1350650112472142.
35.
BriscoeBJEvansDCB. The shear properties of Langmuir-Blodgett layers. Proc Roy Soc Ser A Math Phys Sci1982; 380: 389–407.
