The piston ring pack is the single greatest contributor to mechanical losses in a heavy duty diesel engine, accounting for 1.1–6.8% of the total losses. Therefore, the piston ring-cylinder liner contact is potentially the most rewarding area to study when attempting to reduce mechanical losses in a heavy duty diesel engine. In this work, four different heavy duty diesel engine cylinder liner variants have been tested to evaluate the lubricating conditions that occur when a section of top compression ring is reciprocated against them in a lubricated environment. Two of the cylinder liners were traditional grey cast iron and plateau honed with different honing angles, one had ANS Triboconditioning® applied and the last was plasma sprayed with a stainless steel and ceramic coating, then honed. An experimental test rig was used where friction and film thickness was recorded, by means of an ultrasonic technique. A numerical model was also developed to calculate the friction and film thickness. Comparisons are made between the simulation and experiment, and the four cylinder liner variants are also evaluated. It was found that both simulation and experiment could differentiate between all surfaces and the results from the model and experiment also correlated well with each other. A lower plateau average surface roughness, as exhibited by the ANS Triboconditioning® and plasma liners, led to a significant reduction in friction.
Exxon Mobil. The outlook for energy: a view to 2040. Technical report, Exxon Mobil, 2012.
2.
European Commission. White Paper – roadmap to a single European transport area – towards a competitive and resource efficient transport system. Technical report, 2011.
3.
RichardsonDE. Review of power cylinder friction for diesel engines. Trans ASME: J Eng Gas Turbines Power2000; 122: 506–519.
4.
MichailSKBarberGC. The effects of roughness on piston ring lubrication, part 1: model development. STLE: Tribol Trans1995; 38: 19–26.
5.
MichailSKBarberGC. The effects of roughness on piston ring lubrication, part 2: the relationship between cylinder wall surface topography and oil film thickness. STLE: Tribol Trans1995; 38: 173–177.
6.
JohanssonANilssonPHOhlssonR. New cylinder liner surfaces for low oil consumption. Tribol Int2008; 41: 854–859.
7.
SatoOTakiguchiMAiharaT. Improvement of piston lubrication in a diesel engine by means of cylinder surface roughness. . SAE paper 2004-01-0604, 2004.
8.
AvanEYSpencerADwyer-JoyceR. Experimental and numerical investigations of oil film formation and friction in a piston ring-liner contact. Proc IMechE Part J: J Engineering Tribology2013; 227(2): 126–140.
9.
SöchtingSJSherringtonI. The effect of load and viscosity on the minimum operating oil film thickness of piston-rings in internal combustion engines. Proc IMechE Part J: J Engineering Tribology2009; 223: 383–391.
10.
DucuDODonahueRJGhandhiJB. Design of capacitance probes for oil film thickness measurements between the piston ring and linear in internal combustion engines. J Eng Gas Turbines Power2001; 123: 633–643.
11.
DharAAgarwalAKSaxenaV. Measurement of dynamic lubricating oil film thickness between piston ring and liner in a motored engine. Sensors Actuators A2009; 149: 7–15.
12.
SaadPKamoLMekariM. Modeling and measurement of tribological parameters between piston rings and liner in turbocharged diesel engine. . SAE paper 2007-01-1400, 2007.
13.
SekiTNakayamaKYamadaT. A study on variation in oil film thickness of a piston ring package: variation of oil film thickness in piston sliding direction. JSAE Rev2000; 21: 315–320.
14.
Takiguchi M, Nakayama K, Furuhama S, et al. Variation of piston ring oil film thickness in an internal combustion engine – comparison between thrust and anti-thrust sides. SAE paper 980563, 1998.
Harper P, Dwyer-Joyce RS, Sjödin U, et al. Evaluation of an ultrasonic method for measurement of oil film thickness in a hydraulic motor piston ring. In: Proceedings of the 31st Leeds–Lyon symposium on tribology, Trinity and All Saints College, Horsforth, Leeds, UK, 7–10 September 2005.
17.
AvanEYMillsRSDwyer-JoyceRS. Ultrasonic imaging of the piston ring oil film during operation in a motored engine – towards oil film thickness measurement. SAE Int J Fuels Lubricants2010; 3: 786–793.
18.
MillsRSAvanEYDwyer-JoyceRS. Piezoelectric sensors to monitor lubricant film thickness at piston-cylinder contacts in a fired engine. Proc IMechE Part J: J Engineering Tribology2013; 227: 100–111.
19.
BolanderNWSteenwykBDSadeghiF. Lubrication regime transitions at the piston ring-cylinder liner interface. Proc IMechE Part J: J Engineering Tribology2005; 219: 19–31.
20.
Dwyer-JoyceRSDrinkwaterBWDonohoeCJ. The measurement of lubricant-film thickness using ultrasound. Proc R Soc A: Math Phys Eng Sci2003; 459: 957–976.
21.
GiacopiniMFowellMTDiniD. A mass-conserving complementarity formulation to study lubricant films in the presence of cavitation. ASME: J Tribol2010; 132: 1–12.
22.
BayadaGTalibiMEAHadiKA. Existence and uniqueness for a non-coercive lubrication problem. J Math Anal Appl2007; 327: 585–610.
23.
Cottle RW, Pang J-S and Stone R. The linear complementarity problem. PA, USA: Society for Industrial & Applied Mathematics, 2009.
24.
Kroshko D. OpenOpt: free scientific-engineering software for mathematical modeling and optimization, http://openopt.org (2013, accessed 25 May 2013).
25.
MorrisNRahmaniRRahnejatH. Tribology of piston compression ring conjunction under transient thermal mixed regime of lubrication. Tribol Int2013; 59: 248–258.
26.
SpencerAAlmqvistALarssonR. A semi-deterministic texture-roughness model of the piston ring-cylinder liner contact. Proc IMechE Part J: J Engineering Tribology2011; 225: 1–9.
27.
Zhmud B, Flores G, Verpoort C, et al. A novel surface finishing process for improving tribological properties of cylinder bores. In: Proceedings 6th VDI-conference Zylinderlaufbahn, Kolben, Pleuel, 19–20 June 2012.
28.
Zhmud B, Åkerlund E-B, Jacobson S, et al. ANS triboconditioning: In-manufacture running-in process for improving tribological properties of mechanical parts made of steel or cast iron. In: Proceedings 18th international colloquium tribology – industrial and automotive lubrication, Technische Akademie Esslingen, Stuttgart, Germany, 10–12 January 2012.
29.
GreenwoodJATrippJH. The contact of two nominally flat rough surfaces. Proc Instn Mech Engrs1971; 185: 625–633.
30.
SahlinFLarssonRAlmqvistA. A mixed lubrication model incorporating measured surface topography, part 1: theory of flow factors. Proc IMechE Part J: J Engineering Tribology2010; 224: 335–351.
31.
SahlinFLarssonRMarklundP. A mixed lubrication model incorporating measured surface topography, part 2: roughness treatment, model validation, and simulation. Proc IMechE Part J: J Engineering Tribology2010; 224: 353–365.
32.
JocsakJLiYTianT. Modeling and optimizing honing texture for reduced friction in internal combustion engines. . SAE paper 2006-01-0647, 2006.
33.
DellisPArcoumanisC. Cavitation development in the lubricant film of a reciprocating piston-ring assembly. Proc IMechE Part J: J Engineering Tribology2004; 218: 157–171.
