Freeze-thaw action of rocks has caused many engineering geological disasters in cold regions. Estimation of the freeze-thaw damage degree and strengths loss of rocks are crucial for the prevention of freeze-thaw disasters. The main aim of this research is to investigate the influence of water saturation on the deterioration of rocks under freeze-thaw and find the best evaluation index. P-wave velocity, elastic modulus and porosity, as the widely used indexes, were adopted to define the freeze-thaw damage variables and predict the UCS loss under freeze-thaw. The change law of these three indexes shows that the critical water saturation for causing a considerable freeze-thaw damage of sandstones is approximately 60%∼80%. P-wave velocity is proved to be a competitive nondestructive parameter, which can be measured easily and correctly without any time-consuming mechanical test. In addition, P-wave velocity can be well used to predict strength loss of rocks under freeze-thaw by performing a statistical analysis of experimental data. It is suggested that the P-wave velocity may be the primary and best index to quantify the freeze-thaw damage degree of rocks with different water saturations comparison with the other two indexes. This study can provide a better understanding of the deterioration of physico-mechanical properties for unsaturated rocks and give a reference for the selection of freeze-thaw evaluation indexes.
AltindagRAlyildizISOnarganT (2004)
Mechanical property degradation of ignimbrite subjected to recurrent freeze-thaw cycles. International Journal of Rock Mechanics and Mining Sciences41(6): 1023–1028.
2.
AmirkiyaeiVGhasemiEFaramarziL (2021)
Estimating uniaxial compressive strength of carbonate building stones based on some intact stone properties after deterioration by freeze–thaw. Environmental Earth Sciences80(9): 352.
3.
ASTM D7012-10 (2010). Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures. ASTM International DOI:10.1520/D7012-10.
4.
BinalA (2009)
A new laboratory rock test based on freeze-thaw using a steel chamber. Quarterly Journal of Engineering Geology and Hydrogeology42(2): 179–198.
5.
ChenTMoriNSuzukiT, et al. (2000)
Experimental study on crack development of rock specimens by freezing and thawing cycles. Soils and Foundations40(2): 41–48.
6.
ChenYNiJJiangN, et al. (2014a)
Experimental study on mechanical properties of granite after freeze–thaw cycling. Environmental Earth Sciences71(8): 3349–3354.
7.
ChenYWangPZhangX, et al. (2014b)
Experimental study on mechanical properties of granite in chemical dissolution and freeze-thaw cycles. Chinese Journal of Geotechnical Engineering36(12): 2226–2235.
8.
DeprezMDe KockTDe SchutterG, et al. (2020)
A review on freeze-thaw action and weathering of rocks. Earth-Science Reviews203: 103143.
9.
EslamiJWalbertCBeaucourAL, et al. (2018)
Influence of physical and mechanical properties on the durability of limestone subjected to freeze-thaw cycles. Construction and Building Materials162: 420–429.
10.
FanLXuCWuZ (2020)
Effects of cyclic freezing and thawing on the mechanical behavior of dried and saturated sandstone. Bulletin of Engineering Geology and the Environment79(2): 755–765.
11.
FangWJiangNLuoX (2019)
Establishment of damage statistical constitutive model of loaded rock and method for determining its parameters under freeze-thaw condition. Cold Regions Science and Technology160: 31–38.
12.
FangYQiaoLChenX, et al. (2014)
Experimental study of freezing-thawing cycles on sandstone in Yungang grottos. Rock and Soil Mechanics35(9): 2433–2442. In Chinese)
13.
FeuerMInceI (2015)
Effects of the freeze-thaw (F-T) cycle on the andesitic rocks (Sille-Konya/Turkey) used in construction Building. Journal of African Earth Sciences109: 96–106.
14.
FarrokhrouzMAsefMR (2017)
Experimental investigation for predicting compressive strength of sandstone. Journal of Natural Gas Science and Engineering43: 222–229.
15.
GaoFCaoSZhouK, et al. (2020)
Damage characteristics and energy-dissipation mechanism of frozen-thawed sandstone subjected to loading. Cold Regions Science and Technology169: 102920–102920.9.
16.
GaoFXiongXZhouK, et al. (2019)
Strength degradation model of saturated sandstone under freeze-thaw cycles. Rock and Soil Mechanics40(3): 926–932. (in Chinese)
17.
GhobadMHBabazadehR (2015)
Experimental studies on the effects of cyclic freezing-thawing, salt crystallization, and thermal shock on the physical and mechanical characteristics of selected sandstones. Rock Mechanics and Rock Engineering48(3): 1001–1016.
18.
GökçeMVİnceİFenerM, et al. (2016)
The effects of freeze-thaw (F-T) cycles on the Gödene travertine used in historical structures in Konya (Turkey). Cold Regions Science and Technology127: 65–75.
19.
HanTShiJChenY (2016)
Experimental study on deterioration of mechanical properties of sandstone under combined action of chemical corrosion and freeze-thaw cycles. Chinese Journal of Hydraulic Engineering47(5): 644–655.
20.
HeidariMTorabi-KavehMMohseniH (2016)
Assessment of the effects of freeze-thaw and salt crystallization ageing tests on Anahita temple stone, Kangavar, west of Iran. Geotechnical and Geological Engineering35(1): 121–136.
21.
HuangSYuSYeY, et al. (2022a)
Pore structure change and physico-mechanical properties deterioration of sandstone suffering freeze-thaw actions. Construction and Building Materials330: 127200.
22.
HuangSHeYYuS, et al. (2022b)
Experimental investigation and prediction model for UCS loss of unsaturated sandstones under freeze-thaw action. International Journal of Mining Science and Technology32(1): 41–49.
23.
HuangSCaiYLiuY, et al. (2021a)
Experimental and theoretical study on frost deformation and damage of red sandstones with different water contents. Rock Mechanics and Rock Engineering54(8): 4163–4181.
24.
HuangSHeYLiuG, et al. (2020a)
Effect of water content on the mechanical properties and deformation characteristics of the clay-bearing red sandstone. Bulletin of Engineering Geology and the Environment80(2): 1767–1724.
25.
HuangSHeYLiuX, et al. (2021b)
Experimental investigation of the influence of dry-wet, freeze-thaw and water immersion treatments on the mechanical strength of the clay-bearing green sandstone. International Journal of Rock Mechanics and Mining Sciences138: 104613.
26.
HuangSXinZYeY, et al. (2021c)
Study on the freeze–thaw deformation behavior of the brittle porous materials in the elastoplastic regime based on Mohr-Coulomb yield criterion. Construction and Building Materials268(2): 121799.
27.
HuangSLuZYeZ, et al. (2020b)
An elastoplastic model of frost deformation for the porous rock under freeze-thaw. Engineering Geology278: 105820.
28.
HuangSYeYCuiX, et al. (2020)
Theoretical and experimental study of the frost heaving characteristics of the saturated sandstone under low temperature. Cold Regions Science and Technology174: 103036.
29.
HuangSLiuQChengA, et al. (2018)
A statistical damage constitutive model under freeze-thaw and loading for rock and its engineering application. Cold Regions Science and Technology145: 142–150.
30.
JiaHLiuQXiangW, et al. (2013)
Damage propagation model of saturated sandstone under freeze-thaw cycles. Chinese Journal of Rock Mechanics and Engineering32(S2): 3049–3055.
31.
JiaHXiangWKrautblatterM (2016)
Quantifying rock fatigue and decreasing compressive and tensile strength after repeated freeze‐thaw cycles. Permafrost and Periglacial Processes26(4): 368–377.
32.
JiangLChenYLiuM (2011)
Experimental study on mechanical properties of granite under high/low temperature freeze-thaw cycles. Rock and Soil Mechanics32(S2): 319–323. In Chinese)
33.
JiangZYaoZChenJ (2017)
Effect of freeze-thaw cycles and water content on uniaxial compressive strength of sandstone. Mining Research and Development37(1): 85–88. In Chinese)
34.
Kellerer-PirklbauerA (2017)
Potential weathering by freeze-thaw action in alpine rocks in the european alps during a nine year monitoring period. Geomorphology296: 113–131.
35.
KhanlariGAbdilorY (2015a)
Influence of wet-dry, freeze-thaw, and heat-cool cycles on the physical and mechanical properties of upper red sandstones in Central Iran. Bulletin of Engineering Geology and the Environment74(4): 1287–1300.
36.
KhanlariGSahamiehRZAbdilorY (2015b)
The effect of freeze-thaw cycles on physical and mechanical properties of upper red formation sandstones, Central part of iran. Arabian Journal of Geosciences8(8): 5991–6001.
37.
LangLJiaHGuoY (2012)
Elementary analysis of failure mechanism and mechanical properties of sandstone under freeze-thaw cycling condition water.Resource and power.
30(11): 118–121. (in Chinese)
38.
LemaitreJ (1985)
A continuous damage mechanics model for ductile fracture. Journal of Engineering Materials and Technology107(1): 83–89.
39.
LiJKaundaRBZhouK (2018a)
Experimental investigations on the effects of ambient freeze-thaw cycling on dynamic properties and rock pore structure deterioration of sandstone. Cold Regions Science and Technology154: 133–141.
40.
LiJYuanWWangW (2020)
Physical and mechanical properties of dolomite with freeze-thaw cycles. Science Technology Engineering20(2): 755–762. In Chinese)
41.
LiJZhouKLiuW, et al. (2018b)
Analysis of the effect of freeze–thaw cycles on the degradation of mechanical parameters and slope stability. Bulletin of Engineering Geology and the Environment77(2): 573–580.
42.
LiJZhouKZhangY, et al. (2014)
Experimental study on physical properties in weathered granite under freeze-thaw cycles. Journal of Central South University (Science and Technology)45(3): 798–802. (in Chinese)
43.
LiuHZhangSZhangX (2017)
Experimental study on freeze thaw deterioration characteristics of sandstone under different initial water content. Science Technology Engineering17(26): 322–327. (in Chinese)
44.
LiuQHuangSKangY, et al. (2015)
A prediction model for uniaxial compressive strength of deteriorated rocks due to freeze-thaw. Cold Regions Science and Technology120: 96–107.
45.
LiuYCaiYHuangS, et al. (2020)
Effect of water saturation on uniaxial compressive strength and damage degree of clay-bearing sandstone under freeze-thaw. Bulletin of Engineering Geology and the Environment79(4): 2021–2036.
46.
LvZXiaCQiangL, et al. (2018)
Empirical frost heave model for saturated rock under uniform and unidirectional freezing conditions. Rock Mechanics and Rock Engineering52(3): 955–959.
47.
Jin Y, Chen X, Hong L, et al. (2015) Effect of freeze-thaw cycles on mechanical properties and permeability of red sandstone under triaxial compression. Journal of Mountain Science 12 (1): 218–231.
48.
MingJFanC (2017)
Influence of temperature cycle on physical and mechanical properties of rock. Science Technology Engineering17(13): 261–265. (in Chinese)
49.
MomeniAAbdilorYKhanlariGR, et al. (2016)
The effect of freeze-thaw cycles on physical and mechanical properties of granitoid hard rocks. Bulletin of Engineering Geology and the Environment75(4): 1649–1656.
50.
MutlutürkMAltindagRTürkG (2004)
A decay function model for the integrity loss of rock when subjected to recurrent cycles of freezing-thawing and heating-cooling. International Journal of Rock Mechanics and Mining Sciences41(2): 237–244.
51.
OezbekA (2014)
Investigation of the effects of wetting-drying and freezing-thawing cycles on some physical and mechanical properties of selected ignimbrites. Bulletin of Engineering Geology and the Environment73(2): 595–609.
52.
QuDLiDLiX, et al. (2018)
Damage evolution mechanism and constitutive model of freeze- thaw yellow sandstone in acidic environment. Cold Regions Science and Technology155: 174–183.
53.
ShanRZhangLYangH, et al. (2016)
Experimental study of freeze-thaw properties of saturated red sandstone. The Journal of China University of Mining and Technology45(5): 923–929.
54.
TanXChenWYangJ, et al. (2011)
Laboratory investigations on the mechanical properties degradation of granite under freeze-thaw cycles. Cold Regions Science and Technology68(3): 130–138.
55.
TianYXuS (2017)
Interrelative analysis on physical and mechanical indicators of rock under freezing and thawing cycle condition.Mining Safety and Environmental Protection44(4): 24–27. (in Chinese)
56.
UğurİTokluH (2020)
Effect of multi-cycle freeze-thaw tests on the physico-mechanical and thermal properties of some highly porous natural stones. Bulletin of Engineering Geology and the Environment79(1): 255–267.
57.
WalbertCEslamiJBeaucourAL, et al. (2015)
Evolution of the mechanical behaviour of limestone subjected to freeze-thaw cycles. Environmental Earth Sciences74(7): 6339–6351.
58.
WangPXuJFangX, et al. (2017)
Energy dissipation and damage evolution analyses for the dynamic compression failure process of red-sandstone after freeze-thaw cycles. Engineering Geology221: 104–113.
59.
WangPXuJFangX, et al. (2018)
Water softening and freeze-thaw cycling induced decay of red-sandstone. Rock and Soil Mechanics39(6): 2065–2072. (in Chinese)
60.
WangPXuJLiuS, et al. (2016a)
A prediction model for the dynamic mechanical degradation of sedimentary rock after a long-term freeze-thaw weathering: considering the strain-rate effect. Cold Regions Science and Technology131: 16–23.
61.
WangPXuJLiuS, et al. (2016b)
Static and dynamic mechanical properties of sedimentary rock after freeze-thaw or thermal shock weathering. Engineering Geology210: 148–157.
62.
WangYZhangBLiB, et al. (2021)
A strain-based fatigue damage model for naturally fractured marble subjected to freeze-thaw and uniaxial cyclic loads. International Journal of Damage Mechanics30(10): 1594–1616.
63.
WangZZhuZZhuS (2019b)
Thermo-mechanical-water migration coupled plastic constitutive model of rock subjected to freeze-thaw. Cold Regions Science and Technology161: 71–80.
64.
WengLWuZLiuQ, et al. (2021)
Evolutions of the unfrozen water content of saturated sandstones during freezing process and the freeze-induced damage characteristics. International Journal of Rock Mechanics and Mining Sciences142: 104757.
65.
WengLWuZTaheriA, et al. (2020)
Deterioration of dynamic mechanical properties of granite due to freeze-thaw weathering: Considering the effects of moisture conditions. Cold Regions Science and Technology176: 103092.
66.
WenLLiXSuW (2015)
Study of physico-mechanical properties of slope hard rock in metal mine slope influenced by freeze-thaw cycles. Journal of Mining and Safety Engineering32(4): 689–696. (in Chinese)
67.
WenLLiXTangH, et al. (2017)
Study of physical-mechanical characteristics of rock under different freezen-thawed cycle temperature range and its engineering application. Engineering Mechanics34(5): 247–256. (in Chinese)
68.
WuADengJGuX, et al. (2014)
Research on mechanical properties and damage evolution law of argillaceous dolomite under freeze-thaw cycles. Rock and Soil Mechanics35(11): 3065–3072. (in Chinese)
69.
WuGShenWCuiK, et al. (2019)
Degradation behavior and mechanism of slate under alternating condition of freeze-thaw and wet-dry. Journal of Central South University (Science and Technology)50(6): 1392–1402. (in Chinese)
70.
XuMJiangAYangX, et al. (2021)
Elastoplastic-damage-seepage coupling model and numerical algorithm for rock slope stability evaluation. International Journal of Damage Mechanics30(9): 1450–1360.
71.
XiaoJDingDJiangF, et al. (2010)
Fatigue damage variable and evolution of rock subjected to cyclic loading. International Journal of Rock Mechanics and Mining Sciences47(3): 461–468.
72.
XuGLiuQ (2005)
Analysis mechanism of rock failure due to freeze-thaw cycling and mechanical testing study on freezen-thawed rocks. Chinese Journal of Rock Mechanics and Engineering24(17): 3076–3082.
73.
XuSLiNWangX, et al. (2016)
Damage test and degradation model of saturated sandstone due to cyclic freezing and thawing of rock slopes of open-pit coal mine. Chinese Journal of Rock Mechanics and Engineering35(12): 2561–2571.
74.
YangLZhouKLeiT, et al. (2016)
Dynamic characteristics and failure law of sandstone under freeze-thaw cycles. The Chinese Journal of Nonferrous Metals26(10): 2181–2187.
75.
YavuzH (2011)
Effect of freeze-thaw and thermal shock weathering on the physical and mechanical properties of an andesite stone. Bulletin of Engineering Geology and the Environment70(2): 187–192.
76.
YavuzHAltindagRSaracS, et al. (2006)
Estimating the index properties of deteriorated carbonate rocks due to freeze-thaw and thermal shock weathering. International Journal of Rock Mechanics and Mining Sciences43(5): 767–775.
77.
YongSChengZXuJ, et al. (2020)
Characterisation and evolution of the full size range of pores and fractures in rocks under freeze-thaw conditions using nuclear magnetic resonance and three-dimensional x-ray microscopy. Engineering Geology271: 105616.
78.
YuJChenXLiH, et al. (2015)
Effect of freeze-thaw cycles on mechanical properties and permeability of red sandstone under triaxial compression. Journal of Mountain Science12(1): 218–231.
79.
ZhangHMengXYangG (2020)
A study on mechanical properties and damage model of rock subjected to freeze-thaw cycles and confining pressure. Cold Regions Science and Technology174: 103056.
80.
ZhangHXiaHYangG, et al. (2018)
Experimental research of influence of freeze-thaw cycles and confining pressure on rock physical-mechanical characteristics of rocks. Journal of China Coal Society43(2): 441–448.
81.
ZhangHYangG (2013)
Experimental study of damage deterioration and mechanical properties for freezing-thawing rock. Journal of China Coal Society38(10): 1756–1762.
82.
ZhangJDengHTaheriA, et al. (2019)
Deterioration and strain energy development of sandstones under quasi-static and dynamic loading after freeze-thaw cycles. Cold Regions Science and Technology160: 252–264.
83.
ZhaoTYangGXiJ, et al. (2019)
Experimental study of the macro and micro-scopic damage of cretaceous sandstone subjected to freeze-thaw cycles. Journal of Xi’an University of Science and Technology39(2): 241–248. (in Chinese)
84.
ZhouKXuYLiJ, et al. (2012)
Experimental study of freezing and thawing cycle influence on physical properties of weathered granite. Journal of China Coal Society37(S1): 70–74.
85.
ZhouKZhangYLiJ, et al. (2013)
Degradation mechanism and evolutionary pattern of granites with coarse and fine grains in freezing-thawing condition. Journal of University of Science Technology Beijing35(10): 1249–1255. (in Chinese)
86.
ZhouXRenXYeX, et al. (2021)
Temperature field and anti-freezing system for cold-region tunnels through rock with high geotemperatures. Tunnelling and Underground Space Technology111(3): 103843.
87.
ZhaoYYangTXuT, et al. (2018)
Mechanical and energy release characteristics of different water-bearing sandstones under uniaxial compression. International Journal of Damage Mechanics27(5): 640–656.
