Effect of Electrode Morphology on the Behaviour of Electrorheological Fluids in Torsional Flow

Abstract

In this study, we report experiments on experimental and commercial electrorheological (ER)-fluids in torsional flow. A torsional flow device (clutch) suitable for ER-fluids was designed and constructed. The flow curves measured with this device were compared with flow curves from a conventional rotational viscometer (a concentric-cylinders system). The agreement between the two devices was encouraging. To study the influence of inhomogeneous flow conditions besides the influence of the inhomogeneity of the electric field on the behaviour of an ER-fluid in a clutch mechanism, a set of smooth plates and three further sets of plates with different surface finishes were used in this investigation. Relative to the smooth plates, an increase in the relative ER-effect resulted from both ER-fluids used, when the oblique plates were used in an AC-and DC-field. This improvement in ER-effect seems to be tied to the increase in local field strength at the thick rim of the oblique plate. The addition of metal sheets to the smooth plates of the clutch provided a small increase in ER-effect under AC conditions. But in DC-field, the increase in ER-effect relative to that for smooth plates was rather pronounced, but so was the increase in electric current.

Get full access to this article

View all access options for this article.

References

Abu-Jdayil, B. 1996. Electrorheological Fluids in Rotational Couette Flow, Slit Flow and Torsional Flow (Clutch), Shaker Verlag, Aachen.

Abu-Jdayil, B. and Brunn, P.O. 1995. “Effects of Non-Uniform Electric Field on Slit Flow of an Electrorheological Fluid,” J. Rheology, 39:1327–1341.

Abu-Jdayil, B. and Brunn, P.O. 1996. “Effects of Electrode Morphology on Slit Flow of an Electrorheological Fluid,” J. Non-Newtonian Fluid Mechanics, 63:45–61.

Abu-Jdayil, B. and Brunn, P.O. 1997. “Effects of Coating on the Behaviour of Electrorheological Fluids in Torsional Flow,” Smart Materials and Structures, 6:509–520.

Atkin, R.J. , Shi, X. and Bullough, W.A. 1991. “Solution of the Constitutive Equations for the Flow of an Electrorheological Fluid in Radial Configurations,” J. Rheology, 35:1441–1461.

Brunn, P.O. and Vorwerk, J. 1993. “Determination of the Steady-State Shear Viscosity from Measurements of the Apparent Viscosity for Some Common Types of Viscometers,” Rheologica Acta, 32:380–397.

Hartsock, D.L. , Novak, R.F. and Chaundy, G.J. 1991. “ER fluid Requirements for Automotive Devices,” J. Rheology, 35:1305–1327.

Katsikopoulos, P. and Zukoski, C. 1994. “Effects of Electrode Morphology on the Electrorheological Response,” In: Tao, R. (ed.), Proceedings of the 4th International Conference on Electrorheological Fluids, World Scientific, Singapore.

Monkman, G.J. 1991. “Addition of Solid Structures to Electrorheological Fluids,” J. Rheology, 35:1385–1392.

10.

Otsubo, Y. and Edamura, K. 1997. “Electrorheology of Dilute Suspensions Induced by Hydrodynamic Instability,” J. Non-Newtonian Fluid Mechanics, 71:183–195.

11.

Spurk, J.H. and Huang, Z. 1993. “Electrorheological Material Under Oscillatory Shear,” J. Intelligent Material Systems and Structures, 4:403–408.

12.

Wendt, E. 1996. Personal communications.

13.

Whittle, M. , Atkin, R.J. and Bullough, W.A. 1995. “Fluid Dynamic Limitations on the Performance of an Electrorheological Clutch,” J. Non-Newtonian Fluid Mechanics, 57:61–81.

14.

Wunderlich, Th. and Brunn, P.O. 2000. “Pressure Drop Measurements Inside a Flat Channel – with Flush Mounted and Protruding Electrodes of Variable Length – Using an Electrorheological Fluid,” Experiments in Fluids, 28:455–461.

15.

Yen, W.S. and Achron, P.J. 1991. “A Study of the Dynamic Behavior of an Electrorheological Fluid,” J. Rheology, 35:1375–1384.