Numerical and experimental analysis of low-pressure steam turbine blades coupled with lacing wire

Abstract

Many industrial steam turbine applications require the capability for variable speed operation in combination with high mass flow rates and high back pressure levels. Especially the low-pressure blading has to be designed carefully with respect to the mechanical integrity. An effective way to reduce blade vibration is the introduction of a simple lacing wire to couple the moving blades. In this paper, the structural behavior of blades coupled by a wire is verified by means of linear and nonlinear finite element method. Different modeling techniques for the coupling effects are presented and discussed. Special focus is put on the nonlinear effects of the contact between blade and wire to investigate the frictional damping performance of the system. The obtained numerical results are validated by strain gauge measurements on a full-scale test turbine under real steam conditions in an industrial steam turbine test rig. The experimental data show low blade vibration amplitudes in the whole operational range indicating a high damping performance of the investigated wire design. The calculation results from the forced response analysis including the frictional effects are in good agreement with the experimental data.

Keywords

Low-pressure steam turbine part-span connector lacing wire blade vibration measurement linear and nonlinear FEM contact modeling dry friction frictional damping

Get full access to this article

View all access options for this article.

References

Ancona W and Dowell EH. Design of dry friction dampers for turbine blades. AIAA Paper No. 83-7082, 1983.

Sextro W, Popp K and Wolter I. Improved reliability of bladed disks due to friction dampers. ASME Paper No. 97-GT-189, 1997.

Traupel

. Thermische Turbomaschinen 1968; vol. 22nd ed. Berlin: Springer.

Traupel

. Die Herabsetzung der Erregung von Schaufelschwingungen durch gegenseitiges Verbinden der Schaufeln. Schweizerische Bauzeitung 1957; 75: 822–824.

Prohl

. A method for calculating vibration frequency and stress of a bandaged group of turbine buckets. Trans ASME 1958; 80: 169–180.

Thomas

. Zur Frage der Gefährlichkeit von Paket-oder Einzelschwingungen bandagierter Turbinenschaufeln. Konstruktion 1956; 8: 6–15, 54–59.

Singh

Lucas

. Blade design and analysis, 1st ed. New York: McGraw-Hill, 2011.

Koh KH, Griffin JH, Filippi S, et al. Characterization of turbine blade friction dampers. ASME Paper No. GT2004-53278, 2004.

Petrov

. Direct parametric analysis of resonance regimes for nonlinear vibrations of bladed discs. Trans ASME, J Turbomach 2007; 129: 495–502.

10.

Sextro

. Dynamic contact problems with friction – models, methods, experiments and applications 2002; vol. 3Berlin: Springer.

11.

Szwedowicz J, Slowik S, Mahler A, et al. Nonlinear dynamic analysis of a gas turbine blade for attainment of reliable shroud coupling. ASME Paper No. GT2005-69062, 2005.

12.

Szwedowicz

Secall-Wimmel

Duenck-Kerst

. Damping performance of axial turbine stages with loosely assembled friction bolts: The nonlinear dynamic assessment. Trans ASME, J Eng Gas Turbines Power 2008; 130: 032505–032505.

13.

Jaiswal

Bhave

. Experimental evaluation of damping in a bladed disk model. J Sound Vib 1994; 177: 111–120.

14.

Drozdowski R, Völker L, Häfele M, et al. Experimental and numerical investigation of the nonlinear vibrational behavior of steam turbine last stage blades with friction bolt damping elements. ASME Paper No. GT2015-42244, 2015.

15.

Traupel

. Thermische Turbomaschinen 1977; vol. 13rd ed. Berlin: Springer.

16.

Häfele M, Starzmann J, Grübel M, et al. Numerical investigation of the impact of part-span connectors on aero-thermodynamics in a low pressure industrial steam turbine. ASME Paper No. GT2014-25177, 2014.

17.

Häfele

Traxinger

Grübel

. Numerical and experimental study on aerodynamic optimization of part-span connectors in the last stage of a low-pressure industrial steam turbine. Proc IMechE, Part A: J Power and Energy 2015; 229: 465–476.

18.

Häfele M, Traxinger C, Grübel M, et al. Experimental and numerical investigation of the flow in a low-pressure industrial steam turbine with part-span connectors. Trans ASME, J Eng Gas Turbines Power 2016; 138: 072604.

19.

Siewert C, Panning L, Schmidt-Fellner A, et al. The estimation of the contact stiffness for directly and indirectly coupled turbine blading. ASME Paper No. GT2006-90473, 2006.

20.

Panning L, Sextro W and Popp K. Optimization of interblade friction damper design. ASME Paper No. 2000-GT-0541, 2000.

21.

Szwedowicz J, Kissel M, Ravindra B, et al. Estimation of contact stiffness and its role in the design of a friction damper. ASME Paper No. 2001-GT-0290, 2001.

22.

Johnson

. Contact mechanics, 1st ed. Cambridge: Cambridge University Press, 1987.

23.

Popov

. Contact mechanics and friction, 1st ed. Berlin: Springer, 2002.