Analysis and comparison on the mechanical behaviors of original bolt-column (OBC) joint and improved bolt-column (IBC) joint

Abstract

In this study, OBC joint is improved by incorporating one web, two flanges, and two additional bolts, putting forward a novel semi-rigid joint referred to as IBC joint. Finite element models of both OBC and IBC joints are established and the former is validated based on previous research. Subsequently, a total of 84 numerical models is utilized to investigate and compare the mechanical behaviors of OBC and IBC joints, taking into account different thicknesses of side plate and flange as wll as various loading conditions. The numerical results indicate that: (I) in comparison to OBC joints, the IBC joints exhibit significant enhancements in strong axis bending performance and axial tensile performance, including average enhancement ratios of 48%, 67%, 44%, and 19% in initial strong axis bending stiffness, ultimate strong axis bending moment, initial tensile stiffness and ultimate tension, respectively; (II) compared to OBC joints, the IBC joints demonstrate reduced capacity in axial torsional resistance and axial compressive performance, with mean decline ratios of 54%, 39%, 14%, and 7% in initial torsional stiffness, ultimate torque, initial compressive stiffness and ultimate compression, respectively; (III) OBC joints have better weak axis bending performance compared to IBC joints, but this gap decreases remarkably with increasing thicknesses of side plate and flange; (IV) the initial out-of-plane shear stiffness and ultimate out-of-plane shear of the IBC joint exhibit average enhancement of approximately 20% and 10%, respectively, when compared to those of the OBC joint; (V) regarding in-plane shear performance, the initial stiffness of IBC joints exceeds that of OBC joints by an average ratio of 61%, while IBC joints with flange thickness over 10 mm demonstrate significant improvement in ultimate capacity; (VI) The mechanical performance of OBC and IBC joints shows varying degrees of improvement with an increase in the thicknesses of side plate and flange.

Keywords

Semi-rigid joint numerical analysis mechanical performance failure mode moment-rotation curves load-displacement curves

Get full access to this article

View all access options for this article.

References

See

McConnel

RE.

Large displacement elastic buckling of space structures. J Struct Eng 1983; 112(5): 1052–1069.

Shibata

Kato

Yamada

. Experimental study on the ultimate strength of single-layer reticular domes. In: Proceeding of the fourth international conference of space structures, England, September 1993. Guildford: University of Surry,1993:387–395.

Han

Liu

Ultimate bearing capacity of the welded hollow spherical joints in spatial reticulated structures. Eng Struct 2004; 26: 73–82.

Choo

Qian

Wardenier

Effects of boundary conditions and chord stresses on static strength of thick-walled CHS K-joints. J Constr Steel Res 2006; 62(4): 316–328.

Qiu

Zhao

Analysis and calculation of axial stiffness of tubular X-joints under compression on braces. J Shanghai Jiaotong Univ 2009; 14(4): 410–417.

Lopez

Puente

Aizpurua

Experimental and analytical studies on the rotational stiffness of joints for single-layer structures. Eng Struct 2011; 33(3): 731–737.

Guo

Xiong

Luo

, et al. Experimental investigation on the semi-rigid behaviour of aluminium alloy gusset joints. Thin-Walled Struct 2015; 87: 30–40.

Wang

Fan

Lin

Experimental investigation on the stability of aluminium alloy 6082 circular tubes in axial compression. Thin-Walled Struct 2015; 89: 54–66.

Đuričić

Aleksić

Scepanovic

, et al. Experimental, theoretical and numerical analysis of K-joint made of CHS aluminium profiles. Thin-Walled Struct 2017; 119: 58–71.

10.

Fan

, et al. Mechanical performance of an improved semi-rigid joint system under bending and axial forces for aluminum single-layer reticulated shells. Thin-Walled Struct 2019; 142: 322–339.

11.

Jiang

, et al. Performance analysis and comparison study of two aluminum alloy joint systems under out-of-plane and in-plane loading. An experimental and numerical investigation. Eng Struct 2020; 214(2): 110643.

12.

Fan

Development and key issues of reticulated shells with semi-rigid joints. Eng Mech 2019; 36(7): 1–7.

13.

Ren

Fan

Parametric study and analytical characterization of the bolt-column (BC) joint for single-layer reticulated structures. Eng Struct 2016; 123: 108–123.

14.

Ren

Fan

Experimental and numerical research on a new semi-rigid joint for single-layer reticulated structures. Eng Struct 2016; 126: 725–738.