The influence of nominal stress on wear factors of carbon fibre–reinforced polyetheretherketone (PEEK-OPTIMA ® Wear Performance) against zirconia toughened alumina (Biolox ® delta ceramic)

Abstract

Carbon fibre–reinforced polyetheretherketone is an attractive alternative to ultra-high-molecular-weight polyethylene in artificial joints, but little has been published on the influence of stress on the wear factor. We know that in ultra-high-molecular-weight polyethylene, the wear factor reduces as the normal stress increases, which is counter-intuitive but very helpful in the case of non-conforming contacts. In this study, carbon fibre–reinforced polyetheretherketone (PEEK-OPTIMA^® Wear Performance) has been investigated in a pin-on-plate machine under steady loads and under stresses typical of hip and knee joints. At stresses below about 6 MPa, wear factors are between 10 and a 100 times lower than for ultra-high-molecular-weight polyethylene but at higher stresses the wear factors increase substantially.

Keywords

Wear analysis/testing bio-composites biomaterials tribology of materials

Get full access to this article

View all access options for this article.

References

Scholes

Inman

Unsworth

. Tribological assessment of a flexible carbon-fibre-reinforced poly(ether-ether-ketone) acetabular cup articulating against an alumina femoral head. Proc IMechE, Part H: J Engineering in Medicine 2008; 222: 273–283.

Toth

. Chapter 7. Biocompatibility of polyaryletheretherketone polymers. In: Kurtz

(ed.) PEEK biomaterials handbook. Oxford: Elsevier, 2012, pp.81–92.

Scholes Susan

de Jong

Anthony

. Effect of carbon fibre orientation on the wear of CFR-PEEK/CFR-PEEK bearing couples. In: Proceedings of 21st annual congress of the International Society for Technology in Arthroplasty, Seoul, Korea, 1–4 October 2008, p.190.

Vassiliou

Unsworth

. Is the wear factor dependent on nominal contact stress in UHMWPE contacts? Proc IMechE, Part H: J Engineering in Medicine 2004; 218: 101–107.

Barbour

PSM

Barton

Fisher

. The influence of contact stress on wear of UHMWPE for total replacement hip prostheses. Wear 1995; 181–183: 250–257.

Rostoker

Galante

. Contact pressure dependence of wear rates of ultra high molecular weight polyethylene. J Biomed Mater Res 1979; 13(6): 957–964.

Rose

Goldfarb

Ellis

. On the pressure dependence of the wear of ultra high molecular weight polyethylene. Wear 1983; 92(1): 99–111.

Invibio Biomaterial Solutions. MOTIS polymer typical material properties, http://www.invibio.com (2009, accessed 23 March 2012).

Joyce

Unsworth

Cartwright

. Preliminary comparison of the wear of silane XLPE with that of UHMWPE, both polymers rubbing against hard counterfaces (abstract). J Bone Joint Surg Br 81(Supp. 1): 85.

10.

Joyce

Monk

Scholes

. A multi-directional wear-screening device and preliminary results of UHMWPE articulating against stainless steel. Bio-Med Mater Eng 2000; 10: 241–249.

11.

Wang

Lin

Stark

. Suitability and limitations of carbon fiber reinforced PEEK composites as bearing surfaces for total joint replacements. Wear 1999; 225–229: 724–727.

12.

Scholes

Unsworth

. Pitch-based carbon-fibre-reinforced poly (ether-ether-ketone) OPTIMA assessed as a bearing material in a mobile bearing unicondylar knee joint. Proc IMechE, Part H: J Engineering in Medicine 2009; 223: 13–25.

13.

Kurtz

Nevelos

. Chapter 16. Arthroplasty bearing surfaces. In: Kurtz

(ed.) PEEK biomaterials handbook. Oxford: Elsevier, 2012, pp.261–276.

14.

Scholes

Unsworth

. Wear studies on the likely performance of CFR-PEEK/CoCrMo for use as artificial joint bearing materials. J Mater Sci: Mater Med 2009; 20(1): 163–170.