In the fuel system of an aircraft engine, aero-fuel centrifugal pumps are widely utilized as boost pumps. In this research, we propose the integration of an inlet injector with an aero-fuel centrifugal pump to optimize its flow characteristics and enhance performance. The key geometric parameters of the impeller, volute, and injector are meticulously designed. The effectiveness of our approach is validated through a combination of experimental and numerical analysis, which involves comparing simulation results with experimental data. The findings demonstrate that the presence of the injector significantly impacts the flow characteristics and hydraulic performance of the pump. Specifically, it effectively reduces flow losses in the specific channels of the impeller and volute. Furthermore, the injector enhances the regulation of the inlet flow fields by adjusting the inlet pressure and controlling the suction flow direction. Consequently, the pump’s efficiency is enhanced when equipped with the injector compared to its performance without it. Therefore, incorporating an injector in an aero-fuel centrifugal pump has a positive effect on regulating flow characteristics and improving hydraulic efficiency.
LiuSQ. Investigation of centrifugal pump used as aero-engine main fuel pump. Aeroengine2006; 32: 43–45.
2.
SuttonGP. History of liquid propellant rocket engines, Virginia: American Institute of Aeronautics and Astronautics, 2006.
3.
FanSQ. Aeroengine control. Xi’an: Northwestern Polytechnical University Press, 2008.
4.
ShenZSChuWLiX, et al.Sediment erosion in the impeller of a double-suction centrifugal pump – a case study of the Jingtai Yellow River Irrigation Project, China. Wear2019; 422: 269–279.
5.
ZhangJF. Numerical and experimental investigation on configuration optimization of the large-size ionic wind pump. Energy2019; 171: 624–630.
6.
ArriagaM. Pump as turbine–a pico-hydro alternative in Lao People’s Democratic Republic. Renew Energy2010; 35: 1109–1115.
7.
StechmannD. Design and analysis of a high-pressure turbopump at Purdue University. In Proceedings 51st AIAA/SAE/ASEE Joint Propulsion Conference, USA, 2015, 2015, pp. 4216–4240.
8.
HassantabarANajjaranAFarzaneh-GordM. Investigating the effect of engine speed and flight altitude on the performance of throttle body injection (TBI) system of a two-stroke air-powered engine. Aero Sci Technol2019; 86: 375–386.
9.
CuiBLZhangCLZhangYL, et al.Influence of cutting angle of blade trailing edge on unsteady flow in a centrifugal pump under off-design conditions. Appl Sci2020; 10(2): 580.
10.
ZhengLLChenXPDouHS. Effects of clearance flow on the characteristics of centrifugal pump under low flow rate. J Mech Sci Technol2020; 34(1): 189–200.
11.
WangLKLuJLLiaoWl., et al.Numerical simulation of the tip leakage vortex characteristics in a semi-open centrifugal pump. Appl Sci2019; 9(23): 5244.
12.
WangBGuanHYeZ, Numerical and experimental investigations on flow regulation of fuel vapor core pump, Proc Inst Mech Eng G J Aerosp Eng, 2018; 232(1): 111–120.
13.
ByskovRKJacobsenCBPedersenN. Flow in a centrifugal pump impeller at design and off-design conditions-part II: large eddy simulations. J Fluid Eng2003; 125(1): 73–83.
14.
FengJBenraFKDohmenHJ. Unsteady flow visualization at part-load conditions of a radial diffuser pump: by PIV and CFD. J Visual2009; 12(1): 65–72.
15.
ZhangHHYouHLLuHS, et al.CFD-rotordynamics sequential coupling simulation approach for the flow-induced vibration of rotor system in centrifugal pump. Appl Sci2020; 10(3): 1186.
16.
LiWG. Effects of viscosity on turbine mode performance and flow of a low specific speed centrifugal pump. Applied Mathematical Modeling2016; 40(2): 905–926.
17.
YousefHNoorollahiYTahaniM, et al.Numerical simulation for obtaining optimal impeller’s blade parameters of a centrifugal pump for high-viscosity fluid pumping. Sustain Energy Technol Assessments2019; 34: 16–26.
18.
GuoXMZhuLZhuZC, et al.Numerical and experimental investigations on the cavitation characteristics of a high-speed centrifugal pump with a splitter-blade inducer. J Mech Sci Technol2015; 29: 259–267.
19.
LiuMTanLCaoSL. Theoretical model of energy performance prediction and BEP determination for centrifugal pump as turbine. Energy2019; 172: 712–732.
20.
ShiBWeiJJZhangY. A novel experimental facility for measuring internal flow of Solid-liquid two-phase flow in a centrifugal pump by PIV. Int J Multiphas Flow2017; 89: 266–276.
21.
DerakhshanSPourmahdaviMAbdolahnejadE. Numerical shape optimization of a centrifugal pump impeller using artificial bee colony algorithm. Computers & Fluids2013; 81: 145–151.
22.
WangCShiWWangX, et al.Optimal design of multistage centrifugal pump based on the combined energy loss model and computational fluid dynamics. Appl Energy2017; 187: 10–26.
23.
AnZZhounianLPengW. Multi-objective optimization of a low specific speed centrifugal pump using an evolutionary algorithm. Eng Optim2016; 48(7): 1251–1274.
24.
FengJFWeiXLJieJY, et al.Optimization of cavitation characteristics of aviation fuel centrifugal pump inducer based on surrogate model, Struct Multidiscip Optim2023; 66(11): 202.
25.
ChuanWYulongYYangY, et al., Automatic optimization of centrifugal pump for energy conservation and efficiency enhancement based on response surface methodology and computational fluid dynamics, Engineering Applications of Computational Fluid Mechanics2023; 17(1).
26.
HanXKangYShengJ, et al.Centrifugal pump impeller and volute shape optimization via combined NUMECA, genetic algorithm, and back propagation neural network, Struct Multidiscip Optim2020; 61: 381–409.
27.
YanxiaFJiangfengXYangS, et al.Experimental and numerical study on cavitation performances of a turbopump with and without an inducer, Proc Inst Mech Eng G J Aerosp Eng2022; 236(6): 1098–1111.
28.
MiyakeYNojiINishikawaY, et al.The characteristics of the air-separator of an axial flow fan. Transactions of the Japan Society of Mechanical Engineers, Series B1984; 50(460): 2960–2967.
29.
ZhangHXChenSWMengQH, et al.Flow separation control using unsteady pulsed suction through endwall bleeding holes in a highly loaded compressor cascade. Aero Sci Technol2018; 72: 455–464.
30.
KurokawaJMatsuiJImamuraH, et al.An innovative device to suppress performance-curve instability in a mixed flow pump by use of j-groove. Transactions of the Japan Society of Mechanical Engineers, Series B2000; 66: 460–467.
31.
FuJiiAMizumoSHoriguchiH, et al.A method for the suppression of rotating cavitation by an accumulator at the inlet of an inducer. J Fluid Sci Technol2008; 3(7): 838–845.
32.
ChangNGaneshHYakushijiR, et al.Tip vortex cavitation suppression by active mass injection. J Fluid Eng2011; 133(11): 11301.
33.
KhaleghiHDehkordiMASTousiAM. Role of tip injection in desensitizing the compressor to the tip clearance size. Aero Sci Technol2016; 52: 10–17.
34.
JiaLXinWWanchengW, et al.Performance improvement of a high-speed aero-fuel centrifugal pump through active inlet injector, Proc Inst Mech Eng G J Aerosp Eng2021; 235(8): 859–878.
