This study attempts to determine the effect of and mechanisms for the suppression of the ignition pressure and back-flowing exhaust during a hot launch process in a W-shaped silo, considering the missile movement via dynamic mesh technology. The mixture model for the multiphase and the turbulent model employed were experimentally proved to be accurate and reliable. The numerical results show that the injection of water into a missile exhaust can effectively suppress the ignition overpressure, thereby reducing the time of oscillation and oscillation amplitude, and reducing the maximum pressure at missile bottom from 3.68 × 105 Pa to 2.39 × 105 Pa. In addition, water injection makes the back-flowing exhaust remain at the bottom of the launch duct instead of filling the duct, and it cools the missile bottom, thus leading to a reduction in the maximum temperature from 3000 K to approximately 500 K.
SinhaPKChakrabortyD. Numerical study of hot launch of missile inside a tube. Proc IMechE Part G: J Aerospace Engineering2014; 228: 2604–2611.
5.
MurtyMSRSinhaPKChakrabortyD. Effect of rocket exhaust of canisterized missile on adjoining launching system. Proc IMechE, Part G: J Aerospace Engineering2017; 231: 2085–2097.
6.
BroadwellJETsuCN. Transient pressures caused by rocket start and shutdown in ducted launchers. J Spacecr Rockets1967; 4: 1323–1328.
7.
Sheeran WJ and Hendershot K. Dynamic simulation of the silo launch sequence of solid propellant missiles. In: 7th propulsion joint specialist conference, 14–18 June 1971. Salt Lake City: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.1971-707.
8.
Wayte M and Gruenich F. The use of an expansion tube with cold gas to determine rocket engine starting transient pressures during silo launch. In: 7th aerodynamic testing conference, 13–15 September 1972. Palo Alto: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.1972-997.
9.
WayteMJGruenichFA. Determination of rocket ignition induced silo transient pressures using an expansion tube. J Spacecr Rockets1973; 10: 602–604.
10.
Salita M, Glatt L, Norton C, et al. Modeling of ignition overpressure in Minuteman silos. In: 33rd joint propulsion conference and exhibit, 6–9 July 1997. Seattle: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.1997-2720.
11.
Salita M and Thoms R. Evaluation of CFD code CFD-ACE for application to rocket problems. In: 36th AIAA/ASME/SAE/ASEE joint propulsion conference and exhibit, 24–28 July 2000. Las Vegas: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.2000-3186.
12.
WangFYangSXXuY. Numerical simulation and analysis on W-type silo launching environment (in Chinese). J Solid Rocket Technol2007; 30: 466–469.
13.
Jiang J, Shi S, Niu Y, et al. Jet gas dynamics (in Chinese). Beijing: Beijing Institute of Technology Press, 2015, pp.389–394, 395–411.
14.
LiuZQWangDFZhangZC, et al.Design and validation of small proportion model of missile engine’s flow field (in Chinese). Comput Simul2008; 25: 51–54.
15.
ZhouX. Study on the silo jet flow field during the launching (in Chinese), Beijing: Beijing Institute of Technology, 2015.
16.
Canabal F and Frendi A. On the suppression of ignition overpressure generated by launch vehicles. In: 9th AIAA/CEAS aeroacoustics conference and exhibit, 12–14 May 2003. Hilton Head: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.2003-3329.
17.
Canabal F and Frendi A. Suppression of ignition overpressure generated by launch vehicles. In: 10th AIAA/CEAS aeroacoustics conference, 10–12 May 2004. Manchester: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.2004-2833.
18.
CanabalFFrendiA. Study of the ignition overpressure suppression technique by water addition. J Spacecr Rockets2006; 43: 853–865.
19.
Giordan P, Fleury P and Guidon L. Simulation of water injection into a rocket motor plume. In: 35th joint propulsion conference and exhibit, 20–24 June 1999. Los Angeles: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.1999-2517.
20.
Vu BT, Bachchan N, Peroomian O, et al. Multiphase modeling of water injection on flame deflector. In: 21st AIAA computational fluid dynamics conference, 24–27 June 2013. San Diego: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.2013-2592.
21.
Miller MJ, Koo JH, Sickler FM, et al. Effect of water to ablative performance under solid rocket exhaust environment. In: 29th joint propulsion conference and exhibit, 28–30 June 1993. Monterey: American Institute of Aeronautics and Astronautics. DOI: 10.2514/6.1993-2475.
22.
JiangYMaYWangW, et al.Inhibition effect of water injection on afterburning of rocket motor exhaust plume. Chin J Aeronaut2010; 23: 653–659.
23.
LiJJiangYYuS, et al.Cooling effect of water injection on a high-temperature supersonic jet. Energies2015; 8: 12363–12363.
24.
DehghanMDavariARManshadiMD. Numerical investigation on the weight, speed, and installation location effects on fuel tank separation trajectory. Proc IMechE, Part G: J Aerospace Engineering2017; 231: 2331–2344.
25.
YangLZhangHLinA. Effects of water ingestion on the tip clearance flow in compressor rotors. Proc IMechE, Part G: J Aerospace Engineering2019; 233: 4235–4246.
26.
JohnsonRW. Handbook of fluid dynamics, 2nd ed. Boca Raton: CRC Press, 2016, pp. 67–72.
27.
KolevNI. Multiphase flow dynamics 4: turbulence, gas adsorption and release, diesel fuel properties, Berlin: Springer International Publishing, 2011, pp. 129–129.
ManninenMKallioSTaivassaloV. On the mixture model for multiphase flow, Finland: Espoo Technical Research Centre of Finland, 1996.
30.
BowenRMEringenAC. Theory of mixtures, part I. Continuum physics. III, New York: Academic Press, 1976.
31.
ANSYS. ANSYS fluent theory guide, Canonsburg: ANSYS, Inc., 2016, pp. 537–595.
32.
Lee WH. A pressure iteration scheme for two-phase flow modeling. In: Computational methods for two-phase flow and particle transport. Hackensack: World Scientific, 1980, pp.61–82.
33.
ChengHWangHShiQ, et al.Unsteady aerodynamics investigation of deploying tandem-wing with different methods. Proc IMechE, Part G: J Aerospace Engineering2019; 233: 3714–3733.
34.
SankaranSIgnatiusJKRamkumarR, et al.Suppression of high mach number rocket jet noise by water injection. J Spacecr Rockets2009; 46: 1164–1170.
35.
FarahaniMFouladiNMirbabaeiAR. Design and analysis of a cooling system for a supersonic exhaust diffuser. Proc IMechE, Part G: J Aerospace Engineering2019; 233: 5253–5263.
