Theoretical and experimental studies on the motion and thermal states of oil droplet in a bearing chamber

Abstract

Study on the motion and thermal states of oil droplet is an important part of research on the oil/air two-phase flow and heat transfer in an aero engine bearing chamber. In this paper, dimensional analysis is applied to the airflow analysis of bearing chamber. That makes the analysis model suitable for a wide range of geometric and operating conditions. Moreover, the temperature solution is added to the oil droplet motion analysis. That could promote the calculation accuracy of the droplet trajectory, velocity, and temperature. Firstly, the similarity criteria of the airflow in a bearing chamber are determined based on the dimensional analysis. The airflow distribution general formulas are proposed based on the numerical results of airflow velocity and temperature. The general formulas include 14 similarity criteria and are suitable for various geometric and operating conditions. The reliability of the general formulas is verified by some available experimental results. Secondly, the difference equations of the oil droplet velocity and temperature are listed by the difference method. The velocity and temperature of the droplet are obtained using a step-by-step method. The influence of droplet diameter, shaft rotational speed, air flow rate, and temperature on the oil droplet trajectory, velocity, and temperature are discussed. Thirdly, a test facility is built in order to investigate into the oil droplet motion and thermal states in a bearing chamber. The trajectory and velocity of the oil droplet are measured by the high-speed photography. Lastly, the proposed theoretical method about the oil droplet motion and thermal states is verified by above measurement results. The work in this paper may have a certain significance for perfecting the research system and improving the research level on the oil/air two-phase flow and heat transfer in an aero engine bearing chamber.

Keywords

Aero engine bearing chamber oil droplet heat transfer velocity temperature trajectory high-speed photography similarity criteria

Get full access to this article

View all access options for this article.

References

Klingsporn M. Advanced transmission and oil system concepts for modern aero-engines. In: Proceedings of ASME turbo expo 2008: Power for land, sea and air, Vienna, Austria, 14–17 June 2004, pp.391–398.

Wittig

Glahn

Himmelsbach

. Influence of high rotational speeds on heat transfer and oil film thickness in aero-engine bearing chambers. ASME J Eng Gas Turbines Power 1994; 116: 395–401.

Glahn

Kurreck

Willmann

. Feasibility study on oil droplet flow investigations inside aero engine bearing chambers–PDPA techniques in combination with numerical approaches. ASME J Eng Gas Turbines Power 1996; 118: 749–755.

Gorse P, Willenborg K, Busam S, et al. 3D-LDA measurements in an aero-engine bearing chamber. In: Proceedings of ASME turbo expo 2003: Power for land, sea and air, Atlanta, Georgia, USA, 16–19 June 2003, pp.257–265.

Simmons K, Hibberd S, Wang Y, et al. Numerical study of the two-phase air/oil flow within an aero-engine bearing chamber model using a coupled Lagrangian droplet tracking method. In: Proceedings of ASME pressure vessels and piping conference, Vancouver, BC, Canada, 5–9 August 2002, pp.325–331.

Lee

Palma

Simmons

. Comparison of computational fluid dynamics and particle image velocimetry data for the airflow in an aeroengine bearing chamber. ASME J Eng Gas Turbines Power 2005; 127: 697–703.

Farrall M, Hibberd S and Simmons K. Modelling oil droplet/film interaction in an aero-engine bearing chamber. In: 9th international conference on liquid atomization and spray systems, Sorrento, Italy, 13–17 July 2003.

Farrall

Hibberd

Simmons

. The effect of initial injection conditions on the oil droplet motion in a simplified bearing chamber. ASME J Eng Gas Turbines Power 2008; 130: 125011–125017.

Aidarinis J, Missirlis D, Yakinthos K, et al. CFD modelling and LDA measurements for the air-flow in an aero-engine front bearing chamber. In: Proceedings of ASME turbo expo 2010: Power for land, sea and air, Glasgow, UK, 14–18 June 2010, pp.1201–1208.

10.

Chen

Sun

. Effect of oil droplet deformation on its deposited characteristics in an aeroengine bearing chamber. Proc IMechE, Part G: J Aerospace Engineering 2014; 228: 206–218.

11.

Farrall

Simmons

Hibberd

. A numerical model for oil film flow in an aeroengine bearing chamber and comparison to experimental data. ASME J Eng Gas Turbines Power 2006; 128: 111–117.

12.

Chen

Sun

Wang

. Research into configuration and flow of wall oil film in bearing chamber based on droplet size distribution. Chin J Aeronaut 2011; 24: 355–362.

13.

Farrall

Hibberd

Simmons

. Prediction of air/oil exit flows in a commercial aero-engine bearing chamber. Proc IMechE, Part G: J Aerospace Engineering 2006; 220: 197–202.

14.

Tao

. Heat transfer, Xi’an: Northwestern Polytechnical University Press, 2006, pp. 252–253.

15.

Wilcox

. Turbulence model for CFD, California: DCW Industries Inc, 1993, pp. 124–128.

16.

Menter

. Two-equation eddy-viscosity turbulence models for engineering applications. AIAA J 1994; 32: 1598–1605.

17.

Menter FR, Ferreira JC, Esch T, et al. The SST turbulence model with improved wall treatment for heat transfer predictions in gas turbines. In: Proceedings of the international gas turbine congress 2003, Tokyo, 2–7 November 2003.

18.

Kune

VSJ

. Similarity and modeling in science and engineering, New York: Springer, 2012.

19.

Ashgriz

. Handbook of atomization and sprays, London: Springer Science Business Media, LLC, 2011.

20.

ANSYS CFX Release 13.0. ANSYS CFX solver theory guide. Canonsburg, PA: ANSYS, Inc, 2010.

21.

Esch

Menter

. Heat transfer predictions based on two-equation turbulence models with advanced wall treatment. Turbul Heat Mass Transfer 2003; 4: 6333–6640.

22.

Dean

Voss

. Design and analysis of experiments, New York: Springer-Verlag, 1999, pp. 684–684.

23.

Gorse

Busam

Dullenkopf

. Influence of operating condition and geometry on the oil film thickness in aeroengine bearing chambers. ASME J Eng Gas Turbines Power 2006; 128: 103–110.

24.

Lin

. Design handbook of aero engine - volume 12 transmission and oil system, Beijing: Aviation Industrial Publishing House, 2002, pp. 456–456.

25.

http://www.visionresearch.com .

26.

Glahn

Busam

Blair

. Droplet generation by disintegration of oil films at the rim of a rotating disk. ASME J Eng Gas Turbines Power 2002; 124: 117–124.