On–off and proportional–integral controller for a morphing wing. Part 1: Actuation mechanism and control design

Abstract

The main objective of this research work is the development of an actuation control concept for a new morphing actuation mechanism made of smart materials, which is built from a shape memory alloy (SMA). Two lines of smart actuators were incorporated to a rectangular wing to modify the upper wing surface, made of a flexible skin, with the intention to move the laminar-to-turbulent transition point closer to the wing trailing edge.

After a brief introduction of the morphing wing system architecture and requirements, the actuation lines' design and instrumentation are presented. The integrated controller controls the SMA actuators via an electrical current supply, so that the transducer position can be used to eliminate the deviation between the required values for vertical displacements (corresponding to the optimized airfoils) and their physical values. The final configuration of the integrated controller is a combination of a bi-positional (on–off) controller and a PI (proportional–integral) controller, due to the two heating and cooling phases of the SMA wires' interconnection. This controller must behave like a switch between the cooling and the heating phases, situations where the output current is 0 A, or is controlled by a PI type law. The PI controller for the heating phase is optimally tuned using integral and surface minimum error criteria (Ziegler–Nichols). The controller is numerically tested on the linear identified system in terms of time response, Bode diagram, amplitude and phase stability margins, and root-locus.

Keywords

morphing wing actuation mechanism control design numerical simulation testing

Get full access to this article

View all access options for this article.

References

Smith

Butt

Spakovsky

Moorhouse

A study of the benefits of using morphing wing technology in fighter aircraft systems Proceedings of 39th AIAA Thermophysics Conference, Miami, Florida, USA, 25–28 June 2007.

Butt

A study of morphing wing effectiveness in fighter aircraft using energy analysis and global optimization techniques. MSc Thesis, Faculty of the Virginia Polytechnic Institute and State University, Blacksburg, Virginia, USA, December 2005.

Hinshaw

Analysis and design of a morphing wing tip using multicellular flexible matrix composite adaptive skins. MSc Thesis in Aerospace Engineering, Virginia Polytechnic Institute and State University, Blacksburg, Virginia, USA, 1 July 2009.

Chopra

Review of state of art of smart structures and integrated systems

AIAA J., 2002, 40(11), 2145–2187.

Chang

Shah

Singhee

Parameterization of the geometry of a blended-wing-body morphing wing. Project report no. ME 6104, The Systems Realization Laboratory, Georgia Institute of Technology, Atlanta, Georgia, USA, 28 April 2009.

Gonzalez

Morphing wing using shape memory alloy: a concept proposal, final research paper in 2005 Summer Research Experience for Undergraduates (REU) on nanotechnology and materials systems. Texas Institute of Intelligent Bio-nano Materials and Structures for Aerospace Vehicles (TiiMS) – NASA Research University, Texas A&M University, July 2005, College Station, Texas, USA.

Namgoong

Crossley

Lyrintzis

Aerodynamic optimization of a morphing airfoil using energy as an objective. In Proceedings of 44th AIAA Aerospace Sciences Meeting and Exhibit, Reno, Nevada, USA, 9–12 January 2006.

Majji

Rediniotis

Junkins

Design of a morphing wing: modeling and experiments. In Proceedings of AIAA Atmospheric Flight Mechanics Conference and Exhibit, Hilton Head, South Carolina, USA, 20–23 August 2007.

Baron

Benedict

Branchaw

Ostry

Pearsall

Perlman

Selstrom

Morphing wing (MoW), ASEN 4018 Senior Projects. Department of Aerospace Engineering, University of Colorado, Boulder, Colorado, USA, December 2003.

10.

Iannucci

Fontanazza

Design of morphing wing structures. Proceedings of 3rd Systems Engineering for Autonomous Systems (SEAS) Defence Technology Centre (DTC) Technical Conference, Edinburgh, UK, 24–25 June 2008.

11.

Kota

Hetrick

Osborn

Paul

Pendleton

Flick

Tilmann

Design and application of compliant mechanisms for morphing aircraft structures. Proceedings of SPIE---Smart Structures and Materials 2003: Industrial and Commercial Applications of Smart Structures Technologies, San Diego, California, USA, 3 March, 2003, pp. 24–33, Vol. 5054 (2003).

12.

Nickless

Dynamic modeling and position control of a piezoelectric flextensional actuator. MSc Thesis, Graduate School of the University of Maryland, College Park, Maryland, USA, 2008.

13.

Thill

Etches

Bond

Potter

Weaver

Morphing skins

Aeronaut. J., 2008, 112(1129), 117–139.

14.

Bliss

Bart-Smith

Morphing structures technology and its application to flight control. In Proceedings of Student Research Conference, Virginia Space Grant Consortium Newport News, Virginia, USA, 1 April 2005.

15.

Whitmer

Kelkar

Robust control of a morphing airfoil structure. In Proceedings of American Control Conference, Portland, Oregon, USA, 8–10 June 2005.

16.

Ruotsalainen

Kroneld

Nevala

Brander

Lindroos

Sippola

Shape control of a FRP airfoil structure using SMA-actuators and optical fiber sensors. J. Solid State Phenom., 2009, 144, 196–201- Mechatronic Systems and Materials II.

17.

Lampton

Niksch

Valasek

Reinforcement learning of a morphing airfoil-policy and discrete learning analysis. Proceedings of AIAA Guidance, Navigation and Control Conference and Exhibit, Honolulu, Hawaii, USA, 18–21 August 2008.

18.

Lampton

Niksch

Valasek

Morphing airfoils with four morphing parameters. Proceedings of AIAA Guidance, Navigation and Control Conference and Exhibit, Honolulu, Hawaii, USA, 18–21 August 2008.

19.

Khalid

Jones

Navier stokes investigation of blunt trailing edge airfoils using O-grids

AIAA J. Aircraft, 1993, 30(5), 797–800.

20.

Khalid

Jones

A CFD investigation of the blunt trailing edge airfoils in transonic flow. In Proceedings of Inaugural Conference of the CFD Society of Canada, CFD Society of Canada, Montreal, June 1993.

21.

Popov

Labib

Fays

Botez

Closed-loop control simulations on a morphing wing

AIAA J. Aircraft, 2008, 45(5), 1794–1803.

22.

Georges

Brailovski

Morellon

Coutu

Terriault

Design of shape memory alloy actuators for morphing laminar wing with flexible extrados

J. Mech. Des., 2009, 31(9), 091006–091006.

23.

Terriault

Viens

Brailovski

Non-isothermal finite element modeling of a shape memory alloy actuator using ANSYS

Comput. Mater. Sci., 2006, 36(4), 397–410.

24.

Grigorie

Botez

Adaptive neuro-fuzzy inference system-based controllers for smart material actuator modeling

Proc. IMechE, Part G: J. Aerospace Engineering, 2009, 223(6), 655–668.

25.

Mihoc

. Teoria si Elementele Sitemelor de Reglare Automata, 1980 (Bucuresti, Editura Didactica si Pedagogica).