Finite element modeling and validation of the fastening systems and concrete sleepers used in North America

Abstract

Significant increases in rail loads, as well as growing interest in providing higher-speed passenger rail services, is placing new and increasing existing demands on fastening systems and concrete sleepers. Consequently, there is a strong need to better understand the response of fastening systems and concrete sleepers to these significantly increased demands. This paper presents an experimentally validated three-dimensional (3D) finite element (FE) model of a fastening system and concrete sleeper that can be used to study and improve the design and performance of these systems. In this 3D FE model, the following mechanisms that are critical to the performance of fastening systems and concrete sleepers are included: frictional interaction between components of the fastening system; interaction between shoulders and concrete; and the plastic behavior of each component in the system. The FE model is validated using laboratory experimental tests, in which a lateral load is applied to a single concrete sleeper with two sets of fastening systems. The validated FE model is used to analyze the sleeper/fastening system under different loading scenarios involving various vertical and lateral load combinations. Both component stress and system deflection of the model are analyzed to investigate the system performance at the component and system levels. The results of the study show that FE modeling can be used to investigate the complex behavior of fastening systems and concrete sleepers.

Keywords

Pre-stressed concrete sleeper fastening systems loading path finite element modeling laboratory testing model validation

Get full access to this article

View all access options for this article.

References

American Railway Engineering and Maintenance-of-Way Association. Ties. In: Manual for railway engineering, Lanham, MD: American Railway Engineering and Maintenance-of-Way Association, 2010, pp.30-4-20–30-4-24.

Fröhling

. Low frequency dynamic vehicle/track interaction: modelling and simulation. Veh Syst Dyn 1998; 29: 30–46.

Yu H, Jeong D, Choros J and Sussmann T. Finite element modeling of prestressed concrete cross tie with ballast and subgrade support. In: The ASME 2011 international design engineering technical conference & Computers and information in engineering conference, Washington DC, 29–31 August 2011. NY, USA: ASME.

Yu H and Jeong DY. Finite element modeling of railroad concrete cross ties - a preliminary study. In: The international conference on railway engineering, Beijing, China, 20–21 August 2010. Beijing, China: China Railway Publishing House.

Dahlberg

Lundqvist

. Load impact on railway track due to unsupported sleepers. Proc IMechE, Part F: J Rail Rapid Transit 2005; 219: 67–77.

Remennikov

Kaewunruen

. Investigation of free vibrations of voided concrete sleepers in railway track system. Proc IMechE, Part F: J Rail Rapid Transit 2007; 221: 495–507.

Abrishami

Mitchell

. Bond characteristics of pretensioned strand. ACI Mater J 1993; 90: 228–235.

González-Nicieza

Álvarez-Fernández

Menéndez-Díaz

. Failure analysis of concrete sleepers in heavy haul railway tracks. Engng Fail Anal 2008; 15: 90–117.

Rezaie

Shiri

Farnam

. Experimental and numerical studies of longitudinal crack control for pre-stressed concrete sleepers. Engng Fail Anal 2012; 26: 21–30.

10.

Kaewunruen

Remennikov

. Nonlinear transient analysis of a railway concrete sleeper in a track system. Int J Struct Stab Dyn 2008; 8: 505–520.

11.

Dassault Systemes Simulia Corp. ABAQUS analysis user's manual, Version 6.11, 2011.

12.

Kernes RG, Edwards JR, Dersch MS, et al. Investigation of the dynamic frictional properties of a concrete cross tie rail seat and pad and its effect on rail seat deterioration (RSD). In: The 91st annual meeting of the Transportation Research Board. Washington DC, 22--26 January 2012. Washington DC, USA: Transportation Research Board.

13.

Yamaguchi

. Tribology of plastic materials: their characteristics and applications to sliding components Philadelphia, USA: Elsevier, 1990, pp. 362–362.

14.

Federal Railroad Administration. Track safety standards classes 1 through 5. In: The Federal Railroad Administration track safety standards compliance manual, Washington DC: Federal Railroad Administration, 2007.