Sage Journals: Discover world-class research

Abstract

Grinding is one of the most complex and precise machining operations, with the performance of the grinding wheel being heavily reliant on its surface conditions. Removed chips tend to be forced back to the wheel surface due to the intense heat generated in the grinding zone. The loaded chips block the wheel's grinding capability, resulting in increased grinding force and temperature, wheel chatter, and workpiece thermal degradation. To solve these problems, this research examines the effectiveness of an auxiliary compressed air jet system during the grinding of spk tool steel with an alumina grinding wheel to clean the wheel surface of lodged chips and then the percentage of wheel loading for different tests will also be evaluated. The compressed air nozzle was examined from a variety of perspectives (0, 30, 45, and 60). Grinding with and without a cleaning system, as well as conventional cutting fluid, were also employed as comparisons. In certain output results, input parameters such as grinding wheel speed (20 m/s), cutting depth (20 m), and feed rate (100 mm/s) were maintained constant. When compared to other experiments with different cleaning nozzles, the optimal inclination angle of 45°, which allows the maximum air to reach the interface between the wheel surface and chips, removed chips by pushing them off the wheel surface. Other cleaning nozzles, such as 0°, 30°, and 60°, were less successful. The incidence angle of 45° produced the best results in terms of surface roughness, diametrical grinding wheel wear, G-ratio, tangential forces, specific energy, and wheel loading analysis. Image processing was used to detect and identify chips accumulated between abrasive grains on the wheel surface. To better understand the structure of the wheel and workpiece surface, optical and scanning electron microscopy pictures were taken and analyzed. This research adds to our understanding of the grinding wheel loading mechanism and its dynamics.

Keywords

Grinding wheel loading wheel cleaning image processing compressed air jet

Get full access to this article

View all access options for this article.

References

Chaudhari

Yusufzai

MZK

Vashista

. Grindability study of hard to cut AISI D2 steel upon ultrasonic vibration- assisted dry grinding. Proc IMechE Part E: J Process Mechanical Engineering 2021: 09544089211051635.

Ruzzi RS, Paiva RL, Machado AS, et al . Analysis of temperature and surface finish of Inconel 718 during grinding utilizing different grinding wheels. J Brazilian Soc Mech Sci Eng 2021; 43: 1–12.

Zhang S, Peng W, Xiong Z, et al. Case study for sampling effect in nanometric surface roughness of ultra-precision grinding. Proc IMechE Part E: J Process Mechanical Engineering 2021; 235: 650–656.

Chen F, Mei G, Zhao B, et al. Mechanism of online dressing for micro-diamond grinding wheel during the ultrasound-aided electrolytic in-process dressing grinding. Proc IMechE Part E: J Process Mechanical Engineering 2020; 234: 263–274.

Agarwal

. On the mechanism and mechanics of wheel loading in grinding. J Manuf Process 2019; 41: 36–47.

Dwivedi SP, Sahu R, Saxena A, et al. Recovery of Cr from chrome-containing leather waste and its utilization as reinforcement along with waste spent alumina catalyst and grinding sludge in AA 5052-based metal matrix composites. Proc IMechE Part E: J Process Mechanical Engineering 2021: 09544089211038385.

Chen

Wang

Zhang

. Dynamic characteristics of abrasive grains and machined surface features for variable axis diamond grinding of quartz glass. J Brazilian Soc Mech Sci Eng 2020; 42: 1–15.

Oliveira DD, Guermandi LG, Bianchi EC, et al. Improving minimum quantity lubrication in CBN grinding using compressed air wheel cleaning. J Mater Process Technol 2012; 212: 2559–2568.

Rodriguez RL, Lopes JC, Hildebrandt RA, et al. Evaluation of grinding process using simultaneously MQL technique and cleaning jet on grinding wheel surface. J Mater Process Technol 2019; 271: 357–367.

10.

Sinha MK, Madarkar R, Ghosh S, et al. Some investigations in grindability improvement of Inconel 718 under ecological grinding. Proc IMechE Part B: J Engineering Manufacture 2019; 233: 727–744.

11.

Zhou Y, Ma L, Gong Y, et al. Study on force and temperature characteristics of micro-grinding nickel-based single-crystal superalloy. J Brazilian Soc Mech Sci Eng 2019; 41:1–18.

12.

Khodaii J, Adibi H, Barazandeh F, et al. Improvement of surface integrity in the grinding of bioceramic partially stabilized zirconia using analytical, numerical, and experimental methods. Ceram Int 2020; 46: 13784–13797.

13.

De Oliveira D, Paiva RL, Silva RB, et al. Assessment of the grindability of Inconel 718 under different coolant delivery techniques. J Brazilian Soc Mech Sci Eng 2020; 42: 1–9.

14.

Adibi

Rezaei

Sarhan

. Investigation on using high-pressure fluid jet in grinding process for less wheel loaded areas. Int J Adv Manuf Technol 2014; 70: 2233–2240.

15.

Lopes JC, Garcia MV, Valentim M, et al. Grinding performance using variants of the MQL technique: MQL with cooled air and MQL simultaneous to the wheel cleaning jet. Int J Adv Manuf Technol 2019; 105: 4429–4442.

16.

Yanase

Komori

Ochi

. Grinding of internal gears by setting a large crossed-axes angle using a barrel-shaped grinding wheel. Prec Eng 2018; 52: 384–391.

17.

Nadolny

Plichta

Sutowski

. Regeneration of grinding wheel active surface using high-pressure hydro-jet. J Central South Univ 2014; 21: 3107–3118.

18.

Lopes JC, Ventura CE, Fernandes LD, et al. Application of a wheel cleaning system during grinding of alumina with minimum quantity lubrication. Int J Adv Manuf Technol 2019; 102: 333–341.

19.

Hommel

. Surface roughness terminology and parameters. CT, USA: New Britain, 1988.

20.

Silva LR, Correa EC, Brandao JR, et al. Environmentally friendly manufacturing: behavior analysis of minimum quantity of lubricant-MQL in grinding process. J Cleaner Prod 2020; 256: 103287.

21.

Wójcik

Nadolny

. The effect of the grinding wheel modification on the state of the workpiece surface layer after internal cylindrical grinding of steel C45. Proc IMechE Part E: J Process Mechanical Engineering 2017; 231: 1162–1173.

22.

Belentani RdM, Junior HF, Canarim RC, et al. Utilization of minimum quantity lubrication (MQL) with water in CBN grinding of steel. Mater Res 2014; 17: 88–96.

23.

Ribeiro FSF, Lopes JC, Garcia MV, et al. Grinding performance by applying MQL technique: an approach of the wheel cleaning jet compared with wheel cleaning Teflon and Alumina block. Int J Adv Manuf Technol 2020; 107: 4415–4426.

24.

Hatami

Adibi

Rezaei

. Application of a compressed air jet for cleaning of wheel surface in grinding nickel-based super alloy Inconel 718. CIRP J Manuf Sci Technol 2022; 37: 233–244.

25.

Malkin

Guo

. Grinding technology: theory and application of machining with abrasives. New York, USA: Industrial Press Inc, 2008.

26.

Meireles AB, Bastos FD, Cornacchia TP, et al. Enamel wear characterization based on a skewness and kurtosis surface roughness evaluation. Biotribology 2015; 1: 35–41.

27.

Wang W-z, Chen H, Hu Y-z, et al. Effect of surface roughness parameters on mixed lubrication characteristics. Tribol Int 2006; 39: 522–527.

28.

Sedlaček

Podgornik

Vižintin

. Correlation between standard roughness parameters skewness and kurtosis and tribological behaviour of contact surfaces. Tribol Int 2012; 48: 102–112.

29.

Gonzalez

Woods

Eddins

. Digital image processing. New York, USA: Pearson Education limited, New York, 2018.

30.

Adibi

Rezaei

Sarhan

. Grinding wheel loading evaluation using digital image processing. J Manuf Sci Eng 2014; 136: 011012.

31.

Liu

C-S

Y-A

. Evaluation of grinding wheel loading phenomena by using acoustic emission signals. Int J Adv Manuf Technol 2018; 99: 1109–1117.

32.

Gu Y, Li H, Du B, et al. Towards the understanding of creep-feed deep grinding of DD6 nickel-based single-crystal superalloy. Int J Adv Manuf Technol 2019; 100: 445–455.

Supplementary Material

Please find the following supplemental material available below.

For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.

For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.

0.00 MB

0.79 MB

Evaluation of the grinding process utilizing an auxiliary compressed air jet on cleaning the grinding wheel surface

Abstract

Keywords

Get full access to this article

References

Supplementary Material