At present, magnesium alloys are extensively used in numerous applications due to their light weight and better characteristics. Welding of magnesium alloys is regarded as one of the most complex phenomena in various industries. The friction stir welding of magnesium alloys has encouraged abundant scientific and industrial interest as it has the potency to form a good quality joint. Post welding heat treatment is an appropriate process to further improve the properties or performance of FSW joints. Therefore, the present work aims to join AZ31 Mg alloy plates by friction stir welding, and microstructural and mechanical properties of the joint have been examined. Furthermore, the consequence of post welding heat treatment on the microstructure and mechanical properties of FSW joint has been evaluated. Tensile strength and elongation of FSW joint were about 145.4 ± 4.9 MPa and 9.5 ± 0.9%, respectively. It was found that post welding heat treatment was beneficial in homogenizing grains and to enhance mechanical properties. Tensile strength and elongation of the joint were improved by 4.74% and 15.78% respectively after PWHT. The highest microhardness of stir zone decreased about 6.84% (73 Hv to 68 Hv) after heat treatment and hardness pattern of weld became relatively smooth. Toughness of PWHT joint was 4.5 ± 0.17 Joules. The mode of tensile failure of as-welded and PWHT joint was ductile.
UpadhyayulaVKKParvatkerAGBarothA, et al.
Lightweighting and electrification strategies for improving environmental performance of passenger cars in India by 2030: a critical perspective based on life cycle assessment. J Clean Prod2019;
209: 1604–1613.
2.
LeeSSpeightJGLoyalkaSK.Handbook of alternative fuel technologies.
Boca Raton:
CRC Press, 2015.
HoughtonRA. The contemporary carbon cycle. In: Treatise geochemistry, vol. 10, 2nd ed., Elsevier, 2013, pp. 399–435.
5.
KulekciMK.Magnesium and its alloys applications in automotive industry. Int J Adv Manuf Technol2008;
39: 851–865.
6.
GhassemiehE. Materials in automotive application, state of the art and prospects. In: New trends and developments in automotive industry, InTech, 2011, pp. 365--394.
7.
MonteiroWABusoSJDaLV. Application of magnesium alloys in transport. In: New features on magnesium alloys, InTech, 2012, pp. 1–14.
8.
PietrzykMKuziakRBzowskiKŁ, et al.
Material characterization for numerical simulation of manufacturing of automotive part made of magnesium alloy. Arch. Civ. Mech. Eng2020;
20: 6.
9.
SahuPKDasJChenG, et al.
Friction stir selective alloying of different Al% particulate reinforced to AZ31 Mg for enhanced mechanical and metallurgical properties. Mater Sci Eng A2020;
774: 138889.
10.
ZhangJChenXXiaD, et al.
Improving performance of friction stir welded AZ31/AM60 dissimilar joint by adjusting texture distribution and microstructure. Mater Sci Eng A2020;
778: 139088.
11.
MdSBirruAK.Mechanical and metallurgical properties of friction stir welded dissimilar joints of AZ91 magnesium alloy and AA 6082-T6 aluminium alloy. J Magnes Alloy2019;
7: 264–271.
12.
LiWNiuPYanSR, et al.
Improving microstructural and tensile properties of AZ31B magnesium alloy joints by stationary shoulder friction stir welding. J Manuf Process2019;
37: 159–167.
13.
KadigithalaNKVanithaC. Investigation on the microstructure and mechanical properties of AZ91D magnesium alloy plates joined by friction stir welding. In: Lecture notes in mechanical engineering, Springer, 2020. pp. 1021–1030.
14.
LiGZhouLZhangJ, et al. Macrostructure, microstructure and mechanical properties of bobbin tool friction stir welded ZK60 Mg alloy joints. J Mater Res Technol2020; 9: 9348–9361.
15.
PrasadTSarithaPNarenderBR. Mechanical behaviour of friction stir welding of magnesium AZ-91 Alloy. 2016; 5: 3288–3290.
16.
KumarSPVigneshwarMSelvamaniST, et al.
The comparative analysis on friction stir welded and gas tungsten arc welded AZ91 grade magnesium alloy butt joints. Mater Today Proc2017;
4: 6688–6696.
17.
ChowdhurySHChenDLBholeSD, et al.
Friction stir welded AZ31 magnesium alloy: microstructure. Metall Mat Trans A2013;
44: 323–336.
18.
WangWDengDMaoZ, et al.
Influence of tool rotation rates on temperature profiles and mechanical properties of friction stir welded AZ31 magnesium alloy. Int J Adv Manuf Technol2017;
88: 2191–2200.
19.
XinRLiuDShuX, et al.
Influence of welding parameter on texture distribution and plastic deformation behavior of as-rolled AZ31 Mg alloys. J Alloys Compd2016;
670: 64–71.
20.
Kouadri-HenniABarrallierLBadjiR.Residual stresses of a magnesium alloy (AZ31) welded by the friction stir welding processes. MATEC Web Conf2016;
80: 06003.
21.
SevvelPJaiganeshV.Experimental investigation on the impact of the tool profile in the mechanical properties of FSW AZ31B Mg alloy using optimized process parameters. In: International conference on advances in design and manufacturing, 2014, pp. 912–917.
22.
CaoXJahaziM.Effect of welding speed on lap joint quality of friction stir welded AZ31 magnesium alloy. In: ASM proceedings of the international conference: Trends in welding research, 2009, pp. 72–80.
23.
LiuDXinRZhaoL, et al.
Effect of textural variation and twinning activity on fracture behavior of friction stir welded AZ31 Mg alloy in bending tests. J Alloys Compd2017;
693: 808–815.
24.
XunhongWKuaisheW.Microstructure and properties of friction stir butt-welded AZ31 magnesium alloy. Mater Sci Eng A2006;
431: 114–117.
25.
ComminLDumontMMasseJE, et al.
Friction stir welding of AZ31 magnesium alloy rolled sheets: influence of processing parameters. Acta Mater2009;
57: 326–334.
26.
LimSKimSLeeC-G, et al.
Tensile behavior of friction-stirwelded AZ31-H24 Mg alloy. Metall Mat Trans A2005;
36: 1609–1612.
27.
MironovSOnumaTSatoYS, et al.
Tensile behavior of friction-stir welded AZ31 magnesium alloy. Mater Sci Eng A2017;
679: 272–281.
28.
ChowdhurySMChenDLBholeSD, et al.
Tensile properties of a friction stir welded magnesium alloy: effect of pin tool thread orientation and weld pitch. Mater Sci Eng A2010;
527: 6064–6075.
29.
AfrinNChenDLCaoX, et al.
Microstructure and tensile properties of friction stir welded AZ31B magnesium alloy. Mater Sci Eng A2008;
472: 179–186.
30.
SinghKSinghGSinghH.Microstructure and mechanical behaviour of friction-stir-welded magnesium alloys: as-welded and post weld heat treated. Mater Today Commun2019;
20: 100600.
31.
WangGYanZZhangH, et al.
Improved properties of friction stir-welded AZ31 magnesium alloy by post-weld heat treatment. Mater Sci Technol2017;
33: 854–863.
32.
YanZZhangHDuanJ, et al.
Effect of post-weld heat treatment on mechanical characteristics of AZ31 magnesium alloy welded joints. J Wuhan Univ Technol-Mat Sci Edit2017;
32: 1205–1212.
33.
LobanovLMPashchinNAMikhoduiOL, et al.
Investigation of residual stresses in welded joints of heat-resistant magnesium alloy ML10 after electrodynamic treatment. J Magnes Alloy2016;
4: 77–82.
34.
GuoWWangKWangW, et al.
Influences of post-weld heat treatments on friction stir-welded AZ31B magnesium alloy joints. Rare Met Mater Eng2011;
40: 1075–1078.
35.
Ratna SunilBPradeep Kumar ReddyGMounikaASN, et al.
Joining of AZ31 and AZ91 Mg alloys by friction stir welding. J Magnes Alloy2015;
3: 330–334.
36.
AvedesianMMBakerH.ASM specialty handbook: magnesium and magnesium alloys. ASM International, 1999.
37.
ASTM E8. Standard test methods for tension testing of metallic materials. Annu B ASTM Stand., 2014, 1–28, https://www.astm.org/Standards/E8 (accessed 30 November 2019).
MeshramSReddyM.Influence of tool tilt angle on material flow and defect generation in friction stir welding of AA2219. Def Sc Jl2018;
68: 512–518.
41.
ZhangJLiuKHuangG, et al.
Optimizing the mechanical properties of friction stir welded dissimilar joint of AM60 and AZ31 alloys by controlling deformation behavior. Mater Sci Eng A2020;
773: 138839.
42.
ParkSHCSatoYSKokawaH.Effect of micro-texture on fracture location in friction stir weld of Mg alloy AZ61 during tensile test. Scr Mater2003;
49: 161–166.
43.
SinghKSinghGSinghH.Investigation on the microstructure and mechanical properties of a dissimilar friction stir welded joint of magnesium alloys. Proc IMechE, Part L: J Materials: Design and Applications2019; 233: 2444–2454.
44.
KumarKNBVanithaC.Microstructural developments and mechanical properties of friction stir welding of AZ91D magnesium alloy plates. Metall Mater Eng2017;
23: 119–130.
45.
LeeWBYeonYMJungSB.Joint properties of friction stir welded AZ31B– H24 magnesium alloy. Mater Sci Technol2003;
19: 785–790.
46.
YaoY.Microstructure and corrosion behavior of friction Stir-Welded AZ31 alloy. Int J Electrochem Sci2020;
15: 1058–1071.
47.
AnilchandraARArnbergLBonolloF, et al.
Evaluating the tensile properties of aluminum foundry alloys through reference castings—a review. Materials2017;
10: 1011.
48.
ZhangJFengXSGaoJS, et al.
Effects of welding parameters and post-heat treatment on mechanical properties of friction stir welded AA2195-T8 Al-Li alloy. J Mater Sci Technol2018;
34: 219–227.
49.
SinghICheemaGSKangAS.An experimental approach to study the effect of welding parameters on similar friction stir welded joints of AZ31B-O Mg alloy. Procedia Eng2014;
97: 837–846.
50.
ZhouLLiGHLiuCL, et al.
Effect of rotation speed on microstructure and mechanical properties of self-reacting friction stir welded Al-Mg-Si alloy. Int J Adv Manuf Technol2017;
89: 3509–3516.
51.
AfrinNChenDLCaoX, et al.
Strain hardening behavior of a friction stir welded magnesium alloy. Scr Mater2007;
57: 1004–1007.
52.
CavalierePDe MarcoPP.Fatigue behaviour of friction stir processed AZ91 magnesium alloy produced by high pressure die casting. Mater Charact2007;
58: 226–232.
53.
HanYJiangXChenS, et al.
Microstructure and mechanical properties of electrically assisted friction stir welded AZ31B alloy joints. J Manuf Process2019;
43: 26–34.
54.
UgenderSKumarAReddyAS.Microstructure and mechanical properties of AZ31B magnesium alloy by friction stir welding. Procedia Mater Sci2014;
6: 1600–1609.
55.
SinghKSinghGSinghH.Investigation of microstructure and mechanical properties of friction stir welded AZ61 magnesium alloy joint. J Magnes Alloy2018;
6: 292–298.
56.
ChaiFZhangDLiY.Effect of thermal history on microstructures and mechanical properties of AZ31 magnesium alloy prepared by friction stir processing. Materials2014;
7: 1573–1589.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
