The paper is concerned with the effect of punch angle (0°, 4°, 8°, 16°), sheet thickness (0.8, 2 mm), and punch speed (25, 37.5 mm / min) on the force formation and noise in the blanking of DP600 dual-phase steel sheet. The blanking experiments were carried out in a modular blanking die. The blanking force and noise variables were obtained simultaneously during the blanking using a load cell and noise measuring device, respectively. It was determined that the blanking force significantly decreased with an increasing punch angle, while noise formation decreased. The increase in the punch speed slightly increased the amount of noise while it did not affect the blanking force significantly.
SchmittJHIungT. New developments of advanced high-strength steels for automotive applications. Comptes Rendus Phys2018; 19: 641–656.
2.
DarabiACKadkhodapourJAnarakiAP, et al.Micromechanical modeling of damage mechanisms in dual-phase steel under different stress states. Eng Fract Mech 2021; 243: 107520.
3.
KhedkarPMotagiRMahajanP, et al.A review on advance high strength steels. Int J Curr Eng Technol2016; Special Is: 240–243.
4.
AtzemaEH. 3 – formability of auto components. In: Automotive Steels. Woodhead Publishing, 2017, pp. 47–93.
5.
ChatterjeeD. Behind the development of aAdvanced High Strength Steel (AHSS) including stainless steel for automotive and structural applications -An overview. Mater Sci Metall Eng2017; 4: 1–15.
6.
AydınKKaraağaçİUluerO. The formability and springback characterization of laser-welded DP–HSLA sheets. Appl Phys A2019; 125: 2–11.
7.
BohdalLKukielkaLChodorJ, et al.3D Finite element modelling of sheet metal blanking process. AIP Conf Proc2018; 1960: 1–6.
8.
ShaheenWKanapathipillaiS. Optimization of compound die piercing punches and double cutting process parameters using finite element analysis. Proc Inst Mech Eng Part B J Eng Manuf2020; 234: 3–13.
9.
MuchaJTutakJ. Analysis of the influence of blanking clearance on the wear of the punch, the change of the burr size and the geometry of the hook blanked in the hardened steel sheet. Materials (Basel) 2019; 12: 1261. DOI: 10.3390/ma12081261
10.
CavusogluOGurunH. Investigation and fuzzy logic prediction of the effects of clearance on the banking process of cuzn30 sheet metal. Kov Mater - Met Mater2016; 54: 125–131.
11.
GhiottiARegazzoPBruschiS, et al.Reduction of vibrations in blanking by MR dampers. 60 Excell Invent Met Form2015; 59: 199–204.
12.
CandeloETroiseCMatricanoD, et al.The evolution of the pathways of innovation strategies in the automotive industry. The case of Fiat Chrysler Automobiles. Eur J Innov Manag. Epub ahead of print2021; 1–20. DOI: 10.1108/EJIM-01-2021-0058
13.
GrébanFMonteilGRoizardX. Influence of the structure of blanked materials upon the blanking quality of copper alloys. J Mater Process Technol2007; 186: 27–32.
14.
MirandolaIBertiGACaraccioloR, et al.Machine learning-based models for the estimation of the energy consumption in metal forming processes. Metals 2021; 11: 833. DOI: 10.3390/met11050833.
15.
ZehetnerCReisingerCKunzeW, et al.High-quality sheet metal production using a model-based adaptive approach. Procedia Comput Sci2021; 180: 249–258.
16.
GaldosLOrtubayRMendietaJ, et al.Experimental and numerical investigation of the cutting force during the angle shearing of several steels. AIP Conf Proc 2019; 2113: 080024. DOI: 10.1063/1.5112632.
17.
GürünHGöktaşMGüldaşA. Experimental examination of effects of punch angle and clearance on shearing force and estimation of shearing force using fuzzy logic. Trans FAMENA2016; 40: 19–28.
18.
NothhaftKSuhJGolleM, et al.Shear cutting of press hardened steel: influence of punch chamfer on process forces, tool stresses and sheared edge qualities. Prod Eng2012; 6: 413–420.
19.
MacKensenAGolleMGolleR, et al.Experimental investigation of the cutting force reduction during the blanking operation of AHSS sheet materials. CIRP Ann - Manuf Technol2010; 59: 283–286.
20.
KutunivaKKarjalainenJAMäntyjärviK. Effect of convex sheared punch geometry on cutting force of ultra-high-strength steel. Key Eng Mater2012; 504–506: 1359–1364.
21.
Khleif AAJasim AS. The effect of blanking shear angle on the shearing forces of blanked carbon steel sheets. Int J Mech Eng Technol (IJMET)2018; 9: 1120–1128.
22.
JasimASKhleifAA. An investigation of the shearing forces using blanked carbon steel sheets. Al-Nahrain J Eng Sci2019; 22: 131–135.
23.
SenTBhattacharjeePKBanerjeeD, et al.Study and comparison of the noise dose on workers in a small scale industry in West 1.
24.
XiaQXuTHongG, et al.Prediction of the sound pressure level of blanking noise during sheet-metal blanking using servo press with counterforce. J Mech Sci Technol2014; 28: 1673–1681.
25.
MurakawaMMoJWakatsukiY, et al.Investigation of blanking noise reduction using a hydraulic inertia damper. J Mater Process Technol2001; 112: 205–213.
26.
OtsuM. Reduetlon of blanklng nolse by controlllng press motlon 1. CIRP Ann2003; 52: 245–248.
27.
SanoTHatsukanoKAoiK, et al. Noise analysis of a C-frame mechanical press. In: Proceedings of the twenty-third international machine tool design and research conference. London: Macmillan Education UK, 1983, pp. 59–66.
28.
WangXMaQZhuZ. Low noise control of servo press. In: The 33rd Annual Conference of the IEEE Industrial Electronics Society, Taipei, Taiwan, 2007, pp. 833–838.
29.
GhiottiABarianiPF. Evaluating the press stiffness in realistic operating conditions. In: Advanced methods in material forming. Springer, 2007, pp.189–198.
30.
YuHBLiYCZhangC. Study on mapping of forming precision of workpiece to stiffness of hydropress frame. Mater Sci Forum2012; 697–698: 424–429.
31.
LanJHuJSongC, et al.Modeling and optimization of a 10000KN fine blanking press frame. 2011 Int Conf Remote Sensing, Environ Transp Eng RSETE 2011 - Proc2011: 8353–8357.
32.
OsakadaKMoriKAltanT, et al.Mechanical servo press technology for metal forming. CIRP Ann - Manuf Technol2011; 60: 651–672.
33.
TotreANishadRBodkeS. An overview of factors affecting in blanking processes. Ijetae2013; 3: 1–6.
34.
SlavičJBolkaŠBratušV, et al.A novel laboratory blanking apparatus for the experimental identification of blanking parameters. J Mater Process Technol2014; 214: 507–513.
35.
GaudillièreCRancNLarueA, et al.High speed blanking: an experimental method to measure induced cutting forces. Exp Mech2013; 53: 1117–1126.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
