Analysis of process efficiency in laser fusion cutting and some single- and multi-objective optimization aspects

Abstract

For an efficient use of laser cutting technology, it is of great importance to analyze the impact of process parameters on different performance indicators, such as cut quality criteria, productivity criteria, costs as well as environmental performance criteria (energy and resource efficiency). Having this in mind, this study presents the experimental results of CO₂ laser fusion cutting of AISI 304 stainless steel using nitrogen, with the aim of developing a semi-empirical mathematical model for the estimation of process efficiency as an important indicator of the achievable energy transfer efficiency in the cutting process. The model was developed by relating the theoretical power needed to melt the volume per unit time and used laser power, where the change of kerf width was modeled using an empirical power model in terms of laser cutting parameters such as laser power, cutting speed, and focus position. The obtained results indicated the dominant effect of the focus position on the change in process efficiency, followed by the cutting speed and laser power. In addition, in order to maximize process efficiency and simultaneously ensure high cut quality without dross formation, a laser cutting optimization problem with constraints was formulated and solved. Also, a multi-objective optimization problem aimed at simultaneous optimization of process efficiency and material removal rate was formulated and solved, where the determined set of Pareto non-dominated solutions was analyzed by using the entropy method and multi-criteria decision analysis method, that is, the Technique for Order of Preference by Similarity to Ideal Solution. The optimization results revealed that in order to enhance process efficiency and material removal rate, while ensuring high cut quality without dross formation, focusing the laser beam deep into the bulk of material is needed with particular trade-offs between laser power and cutting speed levels at high pressure levels of nitrogen.

Keywords

stainless steel process efficiency optimization with constraints material removal rate

Get full access to this article

View all access options for this article.

References

Riveiro

Quintero

Boutinguiza

, et al. Laser cutting: a review on the influence of assist gas. Mater 2019; 12: 157.

Schuocker

. Handbook of the EuroLaser academy. 1st ed. London: Chapman & Hall, 1998.

Wandera

Kujanpaa

. Characterization of the melt removal rate in laser cutting of thick-section stainless steel. J Laser Appl 2010; 22: 62–70.

Steen

Mazumder

. Laser material processing. 4th ed. London: Springer, 2010.

Nielsen

Ellis

. Dual-focus laser cutting. Weld World 2002; 46: 33–40.

Sundar

Nath

Bandyopadhyay

, et al. Effect of process parameters on the cutting quality in lasox cutting of mild steel. Int J Adv Manuf Technol 2009; 40: 865–874.

Meško

Zrak

Nigrovič

, et al. The effect of selected technological parameters of laser cutting on the cut surface roughness. Tech Gaz 2018; 25: 997–1003.

Gautam

Mishra

Evaluation of geometrical quality characteristics in pulsed Nd: YAG laser cutting of Kevlar-29/Basalt fiber reinforced hybrid composite using grey relational analysis based on genetic algorithm. FME Trans 2019; 47: 560–575.

Parthiban

Chandrasekaran

Muthuraman

, et al. Optimization of CO₂ laser cutting of stainless steel sheet for curved profile. Mater Today: Proc 2018; 5: 14531–14538.

10.

Gadallah

Abdu

. Modeling and optimization of laser cutting operations. Manuf Rev 2015; 2: 20.

11.

Kadhim

. Effect of laser process an inclined surface cutting of mild steel then analysis data statistically by RSM. J Eng 2019; 25: 120–133.

12.

Sobih

Crouse

. Striation-free laser cutting of mild steel sheets. CIRP Ann 2017; 56: 193–196.

13.

Hirano

Fabbro

. Study on striation generation process during laser cutting of steel. In: International Congress on Applications of Lasers & Electro-Optics, Orlando, USA, 23–27 October 2011.

14.

Pocorni

Petring

Powell

, et al. Measuring the melt flow on the laser cut front. Phys Procedia 2015; 78: 99–109.

15.

Boujelbene

Alghamdi

Miraoui

, et al. Effects of the laser cutting parameters on the micro-hardness and on the heat affected zone of the mi-hardened steel. Int J Adv Appl Sci 2017; 4: 19–25.

16.

Lazov

Narica

Valiniks

, et al. Optimization of CO₂ laser parameters for wood cutting. In: International Scientific and Practical Conference on Environment, Technology and Resources, Rezekne, Latvia, 15–17 June 2017.

17.

Jarosz

Löschner

Niesłony

. Effect of cutting speed on surface quality and heat-affected zone in laser cutting of 316L stainless steel. Procedia Eng 2016; 149: 155–162.

18.

Leone

Genna

. Heat affected zone extension in pulsed Nd: YAG laser cutting of CFRP. Compos Part B: Eng 2018; 140: 174–182.

19.

Aggoune

Amara

Debiane

. Effects of the velocity and the nature of the inert gas on the stainless steel laser cut quality. Fluid Dyn Mater Proc 2013; 9: 61–75.

20.

Pacher

Franceschetti

Strada

, et al. Real-time continuous estimation of dross attachment in the laser cutting process based on process emission images. J Laser Appl 2020; 32: 042016.

21.

Madić

Mladenović

Gostimirović

, et al. Laser cutting optimization model with constraints: maximization of material removal rate in CO₂ laser cutting of mild steel. Proc IMechE, Part B: J Engineering Manufacture 2020; 234: 1323–1332.

22.

Hashemzadeh

Mahammadi

. The effect of power and maximum cutting speed on the material removal rate and cutting volume efficiency in CO₂ laser cutting of polycarbonate sheets. J Mod Process Manuf Prod 2020; 9: 5–23.

23.

Eltawahni

Hagino

Benyounis

, et al. Effect of CO₂ laser cutting process parameters on edge quality and operating cost of AISI316L. Opt Laser Technol 2012; 44: 1068–1082.

24.

Nedić

Erić

Aleksijević

. Calculation of laser cutting costs. Int J Qual Res 2016; 10: 487–494.

25.

Kellens

Rodrigues

Dewulf

, et al. Energy and resource efficiency of laser cutting processes. Phys Procedia 2014; 56: 854–864.

26.

Duflou

Kellens

Devoldere

, et al. Energy related environmental impact reduction opportunities in machine design: case study of a laser cutting machine. Int J Sustain Manuf 2010; 2: 80–98.

27.

Apostolos

Panagiotis

Konstantinos

, et al. Energy efficiency assessment of laser drilling process. Phys Procedia 2012; 39: 776–783.

28.

Wang

. An experimental analysis and optimisation of the CO₂ laser cutting process for metallic coated sheet steels. Int J Adv Manuf Technol 2000; 16: 334–340.

29.

Mahrle

Bartels

Beyer

. Theoretical aspects of the process efficiency in laser beam cutting with fiber lasers. In: International Congress on Applications of Lasers & Electro-Optics, Temecula, USA, 20–23 October 2008.

30.

Girdu

Mihail

Dragoi

. Estimation of laser cutting process efficiency. In: International Scientific Conference – Research and Development of Mechanical Elements and Systems, Kragujevac, Serbia, 5–7 September 2019.

31.

Ion

. Laser processing of engineering materials: principles, procedure and industrial application. 1st ed. Oxford: Butterworth-Heinemann, 2005.

32.

Wandera

. Performance of high power fibre laser cutting of thick-section steel and medium-section aluminium . PhD Thesis, Lappeenranta University of Technology, Finland, 2010.

33.

Goppold

Zenger

Herwig

, et al. Experimental analysis for improvements of process efficiency and cut edge quality of fusion cutting with 1 μm laser radiation. Phys Procedia 2014; 56: 892–900.

34.

Powell

Ivarson

Ohlsson

, et al. Conductive losses experienced during CO₂ laser cutting. High Temper Mater Process 2000; 4: 201–211.

35.

Riveiro

Quintero

Lusquiños

, et al. Study of melt flow dynamics and influence on quality for CO₂ laser fusion cutting. J Phys D: Appl Phys 2011; 44: 135501.

36.

Sparkes

Gross

Celotto

, et al. Practical and theoretical investigations into inert gas cutting of 304 stainless steel using a high brightness fiber laser. J Laser Appl 2008; 20: 59–67.

37.

Chen

. The effects of gas composition on the CO₂ laser cutting of mild steel. J Mater Process Technol 1998; 73: 147–159.

38.

Goppold

Pinder

Herwig

. Dynamic beam shaping for thick sheet metal cutting. In: Lasers in Manufacturing Conference, Munich, Germany, 26–29 June 2017.

39.

Schulz

Hertzler

. Cutting: modeling and data. In: Martienssen

Poprawe

(eds) Numerical data and functional relationships in science and technology. Group 8, advanced materials and technologies. Vol. 1: laser physics and applications. Subvol. C: laser applications. Germany: Springer-Verlag, 2014, pp.187–218.

40.

Madić

Kovačević

Radovanović

, et al. Software tool for the laser cutting process control—solving real industrial case studies. Fact Univ Ser Mech Eng 2016; 14: 135–145.

41.

Yang

. CurveLP-A MATLAB implementation of an infeasible interior-point algorithm for linear programming. Numer Algorithm 2017; 74: 967–996.

42.

Kheloufi

Amara

Benzaoui

. Numerical simulation of transient three-dimensional temperature and kerf formation in laser fusion cutting. J Heat Transf 2015; 137: 112101.

43.

Yilbas

. Effect of process parameters on the kerf width during the laser cutting process. Proc IMechE, Part B: J Engineering Manufacture 2001; 215: 1357–1365.

44.

Fomin

Golyshev

Orishich

, et al. Energy balance in high-quality cutting of steel by fiber and CO₂ lasers. J Appl Mech Tech Phys 2017; 58: 371–378.

45.

Tamilarasan

Rajamani

. Multi-objective optimization of Nd:yAG laser cutting parameters based on BBD-SA hybrid approach. Indian J Eng Mater Sci 2017; 24: 295–300.

46.

Mavrotas

. Effective implementation of the ε-constraint method in multi-objective mathematical programming problems. Appl Math Comput 2009; 213: 455–465.

47.

Park

Nguyen

Dang

. Multi-objective optimization of turning process of hardened material for energy efficiency. Int J Precis Eng Manuf 2016; 17: 1623–1631.