This study proposes and validates a comparative methodology to resolve the critical trade-off between thermal performance and hydraulic resistance in high-power IGBT cooling plates. The work synergistically designs both the inlet/outlet layout and the internal channel structure of a bionic spider-web cooler by applying multi-objective topology optimization (MOTO) to three distinct baseline configurations: a conventional single-inlet/single-outlet (SISO), a segregated multi-inlet/multi-outlet (MIMO), and a mixed MIMO design. The resulting optimized geometries were then reconstructed for comprehensive 3D numerical simulation and comparative analysis. Results show that the optimized mixed-MIMO cooling plate (TO3) significantly outperformed the optimized SISO (TO1) and optimized segregated-MIMO (TO2) designs in heat dissipation, flow resistance, and temperature uniformity. The TO3 design demonstrates a notable reduction in the IGBT base’s temperature difference, with a decrease of 58.6% compared to the TO1 design, and achieved an 8.42 K reduction in maximum temperature. In terms of hydraulic performance, the pressure drop of TO3 is reduced by 15.53% relative to TO1, effectively reducing fluid resistance by mitigating vortex formation. Moreover, the TO3 has a heat transfer coefficient of 2553.8 W/(m2·K), showing an increase of 30.74% compared to the TO1 design. These improvements, along with a higher Nusselt number, highlight the superior convective heat transfer capacity and overall cooling performance of the collaboratively optimized TO3 design.
NeboSEAmaluEHHughesDJ.Critical solder joint in insulated gate bipolar transistors (IGBT) power module for improved mechanical reliability. Microelectron Eng2024; 291: 112200.
2.
ZhangCXuBJasniJ, et al. Three voltage vector duty cycle optimization strategy of the permanent magnet synchronous motor driving system for new energy electric vehicles based on finite set model predictive control. Energies2023; 16(6): 2684.
3.
HuWCuiW.Numerical simulation and optimization of heat dissipation structure for high power insulated gate bipolar transistor (IGBT). J Phys Conf Ser2022; 2290(1): 012122.
4.
GuoweiXRuiMJunjieZ, et al. Thermal performance of an array condenser flat heat pipe for IGBT heat dissipation. Microelectron Reliab2020; 104: 113546.
5.
CiappaM.Selected failure mechanisms of modern power modules. Microelectron Reliab2002; 42(4–5): 653–667.
6.
PanM.Study of the performance of an integrated liquid cooling heat sink for high-power IGBTs. Appl Therm Eng2021; 190: 116827.
7.
AsimMBaigTSiddiquiFR, et al. Advancements in thermal management solutions for electric vehicle high-power electronics: innovations, cooling methods, and future perspectives. J Energy Storage2025; 111: 115344.
8.
HeLJinHZhangY, et al. Review of thermal management system for battery electric vehicle. J Energy Storage2023; 59: 106443.
9.
HamedMMEl-TayebAMoukhtarI, et al. A review on recent key technologies of lithium-ion battery thermal management: external cooling systems. Results Eng2022; 16: 100703.
10.
WeragodaDMTianGBurkitbayevA, et al. A comprehensive review on heat pipe based battery thermal management systems. Appl Therm Eng2023; 224: 120070.
11.
SankerSBBabyR.Phase change material based thermal management of lithium ion batteries: a review on thermal performance of various thermal conductivity enhancers. J Energy Storage2022; 50: 104606.
12.
MorozumiAHokazonoHNishimuraY, et al. Direct liquid cooling module with high reliability solder joining technology for automotive applications. In: 2013 25th International Symposium on Power Semiconductor Devices & IC's (ISPSD), Kanazawa, Japan, 2013, pp. 109–112.
13.
ChenPGaoLLiW, et al. A topology optimization-based-novel design and comprehensive thermal analysis of a cylindrical battery liquid cooling plate. Appl Therm Eng2024; 252: 123747.
14.
LiBWangWBeiS, et al. Analysis of heat dissipation performance of battery liquid cooling plate based on bionic structure. Sustainability2022; 14(9): 5541.
15.
YogeshwarDRepakaRMarathNK.A double serpentine channel liquid cooling plate for hotspot targeted cooling of lithium-ion batteries in a battery module. Int J Therm Sci2025; 209: 109521.
16.
HosseiniradEKhoshvaght-AliabadiM.Proximity effects of straight and wavy fins and their interruptions on performance of heat sinks utilized in battery thermal management. Int J Heat Mass Transf2021; 173: 121259.
17.
ZhangYZuoWLiJ, et al. Performance comparison between straight channel cold plate and inclined channel cold plate for thermal management of a prismatic LiFePO4 battery. Energy2022; 248: 123637.
18.
XieJLiuXZhangG, et al. A novel strategy to optimize the liquid cooling plates for battery thermal management by precisely tailoring the internal structure of the flow channels. Int J Therm Sci2023; 184: 107877.
19.
ZuoWZhangYJiaqiangE, et al. Performance comparison between single S-channel and double S-channel cold plate for thermal management of a prismatic LiFePO4 battery. Renew Energy2022; 192: 46–57.
20.
WangJLiuXLiuF, et al. Numerical optimization of the cooling effect of the bionic spider web channel cold plate on a pouch lithium-ion battery. Case Stud Therm Eng2021; 26: 101124.
21.
ZhanSQueYYinY, et al. A novel tree-like bionic structure for liquid-cooling lithium-ion battery plates. Int J Therm Sci2024; 203: 109098.
22.
LurieSARabinskiyLNSolyaevYO.Topology optimization of the wick geometry in a flat plate heat pipe. Int J Heat Mass Transf2019; 128: 239–247.
SubramaniamVDboukTHarionJ-L.Topology optimization of conjugate heat transfer systems: a competition between heat transfer enhancement and pressure drop reduction. Int J Heat Fluid Flow2019; 75: 165–184.
25.
AsmussenJAlexandersenJSigmundO, et al. A “poor man’s” approach to topology optimization of natural convection problems. Struct Multidiscip Optim2019; 59(4): 1105–1124.
26.
MoonHBoyinaKMiljkovicN, et al. Heat transfer enhancement of single-phase internal flows using shape optimization and additively manufactured flow structures. Int J Heat Mass Transf2021; 177: 121510.
27.
ZhuZZhangDZhengY, et al. Numerical analysis of battery thermal management based on multi-objective topology optimization of liquid cooling plate. Numer Heat Transf A Appl2025; 22: 1–21.
28.
ZhangJZhangDZhengY.Multi-objective topology optimization of flow channels in liquid-cooled plates for battery thermal management system. Struct Multidiscip Optim2025; 68(10): 156.
29.
LiHDingXMengF, et al. Optimal design and thermal modelling for liquid-cooled heat sink based on multi-objective topology optimization: an experimental and numerical study. Int J Heat Mass Transf2019; 144: 118638.
30.
ZhangKLiYChangS-M, et al. Hydraulic and thermal performance enhancement for the cold plate using topology optimization. Appl Therm Eng2024; 236: 121829.
31.
JiHLuoTDaiL, et al. Topology design of cold plates for pouch battery thermal management considering heat distribution characteristics. Appl Therm Eng2023; 224: 119940.
32.
XiaYChenLLuoJ, et al. Numerical investigation of microchannel heat sinks with different inlets and outlets based on topology optimization. Appl Energy2023; 330: 120335.
33.
ZhanSChengZYinY, et al. Effect of inlet and outlet positions on heat dissipation performance of lithium-ion battery cold plates: an analysis based on topology optimization. Int J Heat Mass Transf2023; 215: 124436.
34.
GuoCLiuHGuoQ, et al. Investigations on a novel cold plate achieved by topology optimization for lithium-ion batteries. Energy2022; 261: 125097.
35.
HanXLiuHXieG, et al. Topology optimization for spider web heat sinks for electronic cooling. Appl Therm Eng2021; 195: 117154.
36.
QianSWangWGeC, et al. Topology optimization of fluid flow channel in cold plate for active phased array antenna. Struct Multidiscip Optim2018; 57: 2223–2232.
37.
RenJQiuXWangS.A liquid cooling plate based on topology optimization and bionics simplified design for battery cooling. J Energy Storage2024; 102: 114171.
38.
ChenFWangJYangX.Topology optimization design and numerical analysis on cold plates for lithium-ion battery thermal management. Int J Heat Mass Transf2022; 183: 122087.
