Development of a steering-system model considering viscous friction and its verification

Abstract

A method to model the column-type electric power steering system considering viscous friction is proposed. In general column-type electric power steering systems, viscous friction occurs in the reducer. However, it is very difficult to predict with respect to modelling because it varies with the conditions, and accordingly many parameters should be considered. In this study, in order to estimate the dynamic behaviour of a column-type electric power steering system which uses a worm gear as a reducer, the viscous friction generated in the worm gear was derived through theoretical approaches, and the results were applied to modelling the steering system. In the theoretical approaches, the gear geometry and Hertz’s law were employed to derive parameters such as the normal load and the sliding velocity from the worm gear’s driving conditions. Then, the derived parameters were applied to a tribometer to measure the friction coefficients between the worm and the worm wheel. Finally, the friction coefficients were converted to the viscous friction torque of the steering system. By applying the converted viscous friction torque to the modelling, the entire steering system was modelled and the results were verified by comparative simulations and experiments. To model the entire steering system, the individual subparts of the steering system such as the steering column, the universal joint and the rack-and-pinion gear were modelled with MATLAB/Simulink. Then, for verification of the steering-system model, the dynamic behaviour of the steering system was measured experimentally and compared with the simulation results. Taking into account viscous friction and all the mechanical characteristics of the steering system, the established steering-system model which considers viscous friction was employed to estimate very accurately the dynamic behaviour of the steering system, whereas use of the steering-system model which does not consider viscous friction did not achieve accurate estimations.

Keywords

Viscous friction steering-system model friction coefficient electric power steering

Get full access to this article

View all access options for this article.

References

Norman

. Objective evaluation of on-center handling performance. SAE paper 840069, 1984.

Kurishige

Wada

Kifuku

. A new EPS control strategy to improve steering wheel returnability. SAE paper 2000-01-0815, 2000.

ISO 13674-1:2003 Road vehicles – test method for the quantification of on-centre handling – Part 1: weave test. Geneva: International Organization for Standardization, 2003.

Pfeffer

Harrer

Johnston

. Interaction of vehicle and steering system regarding on-centre handling. Veh System Dynamics2008; 46(5): 413–428.

Chen

Yang

Chen

. A generic model-based advanced control of electric power-assisted steering systems. IEEE Trans Control Systems Technol2008; 16(6): 1289–1300.

Parmar

Hung

. A sensorless optimal control system for an automotive electric power assist steering system. IEEE Trans Ind Electron2004; 51(2): 290–298.

Song

Boo

Kim

. Model development and control methodology of a new electric power steering system. Proc IMechE Part D: J Automobile Engineering2004; 218(9): 967–978.

Zhao

X-P

Chen

. Sliding mode control for torque ripple reduction of an electric power steering system based on a reference model. Proc IMechE Part D: J Automobile Engineering2008; 222(12): 2283–2290.

Kis

Janosi

. Improved handling characteristics of off-road vehicles by applying active control of steering wheel torque. Int J Sustainable Construct Des2011; 2(1): 66–74.

10.

Cholakkal

Chen

. Fault tolerant control of electric power steering using kalman filter-simulation study. In: IEEE international conference on electro/information technology (ed Khalid

), Windsor, Ontario, Canada, 7–9 June 2009, pp.128–133. New York: IEEE.

11.

Data

Pesce

Reccia

. Identification of steering system parameters by experimental measurements processing. Proc IMechE Part D: J Automobile Engineering2004; 218(8); 783–792.

12.

Kim

Shin

Byun

. Efficiency prediction of worm gear with plastic worm wheelInt J Precision Engng Mfg2012; 13(2): 167–174.

13.

Sugawara

Maeda

Wei

. Electric power steering device. Patent WO2010/087295 A1, 2010.

14.

Yamaguchi

. Tribology of plastic materials. New York: Elsevier, 1990.

15.

Townsend

. Dudley’s gear handbook. 2nd edition.New York: McGraw-Hill, 1992.

16.

Willkes

Walsh

Appleyard

. Gearbox assembly for an electric power steering system. Patent WO2009/138964 A1, 2009.

17.

Hiltcher

Guingand

de Vaujany

J-P

. Load sharing of worm gear with a plastic wheel. J Mech Des2007; 129: 23–30.

18.

Litvin

Fuentes

. Gear geometry and applied theory. 2nd edition.Cambridge: Cambridge University Press, 2004.

19.

Simon

. Computer aided loaded tooth contact analysis in cylindrical worm gears. J Mech Des2005; 127: 973–981.

20.

Simon

. The influence of gear hobbing on worm gear characteristics. Trans ASME, J Mfg Sci Engng2007; 129: 919–925.

21.

Badawy

Zuraski

Bolourchi

. Modeling and analysis of an electric power steering system. SAE paper 1999-01-0399, 1999.

22.

Stephen

Norman

Thomas

. An introduction to the mechanics of solids. 2nd edition.New York: McGraw-Hill, 1999.

23.

Kamble

Saha

. Developing a virtual prototype of a rack and pinion steering system. Int J Veh Systems Modelling Test2007; 2(1): 61–79.