This study examines the mechanical and microstructural features of a 36-layer Al5356 wall constructed on an Al6061 substrate utilizing Cold Metal Transfer-Wire Arc Additive Manufacturing. Using tensile, impact, and wear tests, microhardness measurements, fractography, and Electron Backscatter Diffraction (EBSD), property changes along the wall’s height were assessed, notably in the top, middle, and bottom. Performance varied along the building direction. The top layers had 30% higher ultimate tensile strength and impact toughness than the lower levels. EBSD found finer grain structures and more high-angle grain boundaries at the top, increasing strength and critical resolved shear stress. Microhardness rose from bottom to top, with the lowest region 20% lower. Due to surface oxide formation, top layers exhibited stronger wear resistance, decreased friction, and narrower and shallower wear tracks. Due to higher heat input and thermal cycling during deposition, coarser grains and mechanical degradation caused reduced bottom layer performance. These findings highlight the relevance of thermal history in defining WAAM-fabricated aluminum structures.
TrdanUGrumJ.Evaluation of corrosion resistance of AA6082-T651 aluminium alloy after laser shock peening by means of cyclic polarisation and ElS methods. Corros Sci2012; 59: 324–333.
2.
AldalurESuárezAVeigaF.Metal transfer modes for Wire arc additive manufacturing Al-Mg alloys: influence of heat input in microstructure and porosity. J Mater Process Technol2021; 297: 117271.
3.
MaCYanYYanZ, et al. Efficient manufacturing of Al–Mg alloys using controlled low heat input wire and arc additive manufacturing. J Mater Process Technol2023; 314: 117899.
4.
SuDZhangJWangB.The microstructure and weldability in welded joints for AA 5356 aluminum alloy after adding modified trace amounts of Sc and Zr. J Manuf Process2020; 57: 488–498.
5.
GaurVEnokiMOkadaT, et al. A study on fatigue behavior of MIG-welded Al-Mg alloy with different filler-wire materials under mean stress. Int J Fatigue2018; 107: 119–129.
6.
RomhanjiEPopovicM.Problems and the prospect of Al-Mg alloys application in marine constructions. Metallurgical2006; 12: 297–307.
7.
LiZYanHChenJ, et al. Enhancing damping capacity and mechanical properties of Al-Mg alloy by high strain rate hot rolling and subsequent cold rolling. J Alloys Comp2022; 908: 164677.
8.
MehdiyevZFelhoC.Metal additive manufacturing in automotive industry: a review of applications, advantages, and limitations. Mater Sci Forum2023; 1103: 49–62.
9.
MadhavadasVSrivastavaDChadhaU, et al. A review on metal additive manufacturing for intricately shaped aerospace components. CIRP J Manuf Sci Technol2022; 39: 18–36.
10.
SelemaAIbrahimMNSergeantP.Metal additive manufacturing for electrical machines: technology review and latest advancements. Energies2022; 15(3): 1076.
11.
MuruganPDVijayananthSNatarajanMP, et al. A current state of metal additive manufacturing methods: a review. Mater Today Proc2022; 59: 1277–1283.
12.
SinghSRKhannaP.Wire arc additive manufacturing (WAAM): a new process to shape engineering materials. Mater Today Proc2021; 44: 118–128.
13.
YuLChenKZhangY, et al. Microstructures and mechanical properties of NiTi shape memory alloys fabricated by wire arc additive manufacturing. J Alloys Comp2022; 892: 162193.
14.
ChaturvediMScutelnicuERusuC, et al. Wire arc additive manufacturing: review on recent findings and challenges in industrial applications and materials characterization. Metals2021; 11: 939.
15.
KnezovićNTopićA. Wire and arc additive manufacturing (WAAM)–a new manufacturing advancement. New technologies, development, and application. Vol. 4. Springer International Publishing, 2018, pp.65–71.
16.
KöhlerMFiebigSHenselJ, et al. Wire and arc additive manufacturing of aluminum components. Metals2019; 9: 608.
17.
RodriguesTADuarteVMirandaRM, et al. Current status and perspectives on wire and arc additive manufacturing (WAAM). Materials2019; 12: 1121.
18.
AlbannaiAILeón-HenaoHRamirezAJ.Preventing columnar grains growth during hybrid wire arc additive manufacturing of austenitic stainless steel 316L. Eng Rep2024; 6: e12914.
19.
KumarMSJeyaprakashNYangCH.Effect of combined parametric impacts on collapsing the wall quality of WAAM Al5356 component. Eng Fail Anal2024; 166: 108848.
20.
TomarBShivaSNathT.A review on wire arc additive manufacturing: processing parameters, defects, quality improvement, and recent advances. Mater Today Commun2022; 31: 103739.
21.
LiuYLiuZZhouG, et al. Microstructures and properties of Al-Mg alloys manufactured by WAAM-CMT. Materials2022; 15: 5460.
22.
PrasannaNBMalarvizhiSBalasubramanianV.Mechanical properties and microstructural characteristics of AA5356 aluminum alloy cylindrical components made by wire arc additive manufacturing process. Mater Perform Charact2022; 11: 73–98.
23.
PanchenkoOKurushkinDMushnikovI, et al. A high-performance WAAM process for Al–Mg–Mn using controlled short-circuiting metal transfer at increased wire feed rate and increased travel speed. Mater Des2020; 195: 109040.
24.
YehorovYda SilvaLJScottiA.Balancing WAAM production costs and wall surface quality through parameter selection: a case study of an Al-Mg5 alloy multilayer-non-oscillated single pass wall. J Manuf Mater Process2019; 3: 32.
25.
WangJZhuKZhangW, et al. Microstructural and defect evolution during WAAM resulting in mechanical property differences for AA5356 component. J Mater Res Technol2023; 22: 982–996.
26.
LiYZhangXMaXJ. Microstructures and mechanical properties of the MIG welding joint of 7005 aluminum alloy. In: 2nd annual international conference on advanced engineering materials, 2016, pp.334–338. Atlantis Press.
27.
AnandMBishwakarmaHKumarN, et al. Fabrication of multilayer thin wall by WAAM technique and investigation of its microstructure and mechanical properties. Mater Today Proc2022; 56: 927–930.
28.
PrabuGJeyaprakashNYangCH, et al. Analysis on the transformation of melt wear to self-healing crack of wire arc additive manufactured Al 5356 alloy. Tribol Int2023; 188: 108802.
29.
YangQXiaCDengY, et al. Microstructure and mechanical properties of AlSi7Mg0.6 aluminum alloy fabricated by wire and arc additive manufacturing based on cold metal transfer (WAAM-CMT). Materials2019; 12: 2525.
30.
GuoXLiHXueP, et al. Microstructure and mechanical properties of 600 MPa grade ultra-high strength aluminum alloy fabricated by wire-arc additive manufacturing. J Mater Sci Technol2023; 149: 56–66.
31.
ZhouPZhouJYeZ, et al. Effect of grain size and misorientation angle on fatigue crack growth of nanocrystalline materials. Mater Sci Eng2016; 663: 1–7.
32.
SinglaJKumarNBansalA.Microstructural and mechanical properties of Al-5356 alloy structures fabricated using direct energy deposition (DED): In-pursuit to optimizing deposition parameters. Mater Charact2024; 216: 114321.
33.
GuoYCollinsDMTarletonE, et al. Measurements of stress fields near a grain boundary: exploring blocked arrays of dislocations in 3D. Acta Mater2015; 96: 229–236.
34.
GarbatovYÅsSKDen BestenH, et al. Fatigue and fracture. In: 21st international ship and offshore structures congress, ISSC 2022, 2022, pp.501–641. Society of Naval Architects and Marine Engineers.
