The multi-stage sequential process with multi-objective is a complex problem to address as the decision made at a particular stage influences the subsequent stage and vice versa. In this article, the effects of input variables of plastic injection, mold, and different plating stages were investigated on different output responses, namely weldline, warpage, length, and various metal plating thicknesses. This paper investigates a real-time industrial data of manufacturing an automotive exterior part made of ABS material. A D-optimal experimental layout with 55 experiments was generated for eight input factors each at three levels. Nine different output responses in each experiment were normalized into a weighted grey relational grade using grey relational analysis coupled with principal component analysis. The solutions obtained by the analysis of variance on weighted grey relational grade, and by the desirability analysis of D-optimal were compared and validated. The confirmation experiments recorded an average improvement in cumulative process outputs as 40.56% by grey relational analysis and 38.50% by desirability analysis.
SunXZengDTibbenhamP, et al.A new characterizing method for warpage measurement of injection-molded thermoplastics. Polym Test2019; 76: 320–325.
2.
JayswalSJangadeHAbhishekK, et al.Design and simulation of seat handle using plastic injection molding process. In: Deb DBalas VEDey R (eds). Innovations in infrastructure, Singapore: Springer Singapore, 2019, pp. 385–393.
3.
Alvarado-Iniesta A, Cuate O and Schütze O. Multi-objective and many objective design of plastic injection molding process. Int J Adv Manuf Technol. Epub ahead of print 2019. DOI: 10.1007/s00170-019-03432-8.
4.
Kauffer PH. Injection molding: process, design, and applications. Hauppauge, NY: Nova Science Publishers, 2011.
5.
TranterJBRefaloPRochmanA. Towards sustainable injection molding of ABS plastic products. J Manuf Process2017; 29: 399–406.
6.
ChenWCFuGLTaiPH, et al.Process parameter optimization for MIMO plastic injection molding via soft computing. Expert Syst Appl2009; 36: 1114–1122.
7.
Shiroud HeidariBHedayati MoghaddamADavachiSM, et al.Optimization of process parameters in plastic injection molding for minimizing the volumetric shrinkage and warpage using radial basis function (RBF) coupled with the k-fold cross validation technique. J Polym Eng2019; 0: 481–492.
8.
Oduguwa V, Tiwari A and Roy R. Sequential process optimisation using genetic algorithms. In: Yao X, Burke EK, Lozano JA, et al. (eds) Parallel problem solving from nature - PPSN VIII. Berlin, Heidelberg: Springer Berlin Heidelberg, 2004, pp.782–791.
9.
OliaeiEHeidariBSDavachiSM, et al.Warpage and shrinkage optimization of injection-molded plastic spoon parts for biodegradable polymers using Taguchi, ANOVA and artificial neural network methods. J Mater Sci Technol2016; 32: 710–720.
10.
TiwariAOduguwaVRoyR. Rolling system design using evolutionary sequential process optimization. IEEE Trans Evol Comput2008; 12: 196–202.
11.
SchmidtA. Numerical prediction and sequential process optimization in sheet forming based on genetic algorithm. Mater Manuf Process2011; 26: 521–526.
12.
Nellippallil AB, Song KN, Goh C-H, et al. A goal oriented, sequential process design of a multi-stage hot rod rolling system. In: 42nd design automation conference, 2016, V02BT03A007. New York: ASME.
13.
RizviSJASinghAKBhaduGR. Optimization of tensile properties of injection molded α-nucleated polypropylene using response surface methodology. Polym Test2017; 60: 198–210.
14.
Yasiin A, Fathullah M, Shayfull Z, et al. Warpage minimization: analysis using response surface methodology (RSM) and particle swarm optimization (PSO) on thin part. In: AIP conference proceedings, Vol. 1885. Epub ahead of print 2017. DOI: 10.1063/1.5002369.
15.
KimH-GSonHJLeeD-K, et al.Optimization and analysis of reaction injection molding of polydicyclopentadiene using response surface methodology. Korean J Chem Eng2017; 34: 2099–2109.
16.
NguyenTKHwangCJLeeBK. Numerical investigation of warpage in insert injection-molded lightweight hybrid products. Int J Precis Eng Manuf2017; 18: 187–195.
17.
ChenW-CNguyenM-HChiuW-H, et al.Optimization of the plastic injection molding process using the Taguchi method, RSM, and hybrid GA-PSO. Int J Adv Manuf Technol2016; 83: 1873–1886.
18.
OzcelikBOzbayADemirbasE. Influence of injection parameters and mold materials on mechanical properties of ABS in plastic injection molding. Int Commun Heat Mass Transf2010; 37: 1359–1365.
19.
ErzurumluTOzcelikB. Minimization of warpage and sink index in injection-molded thermoplastic parts using Taguchi optimization method. Mater Des2006; 27: 853–861.
20.
JulongD. Introduction to grey system theory. J Grey Syst1989; 1: 1–24.
21.
KangCShiYHeX, et al.Multi-response optimization of T300/epoxy prepreg tape-wound cylinder by grey relational analysis coupled with the response surface method. Mater Res Express. Epub ahead of print 2017. DOI: 10.1088/2053-1591/aa82f5.
22.
WangPZhuZWangY. A novel hybrid MCDM model combining the SAW, TOPSIS and GRA methods based on experimental design. Inf Sci (Ny)2016; 345: 27–45.
23.
VermaRSinghNP. GRA based network selection in heterogeneous wireless networks. Wirel Pers Commun2013; 72: 1437–1452.
24.
ChinnaiyanPJeevananthamAK. Multi-objective optimization of single point incremental sheet forming of AA5052 using Taguchi based grey relational analysis coupled with principal component analysis. Int J Precis Eng Manuf. Epub ahead of print 2014. DOI: 10.1007/s12541-014-0595-3.
25.
PearsonK. On lines and planes of closest fit to systems of points in space. Philos Mag1901; 2: 559–572.
26.
HotellingH. Analysis of a complex of statistical variables into principal components. J Educ Psychol1933; 24: 417–441.
27.
VarunAVenkaiahN. Grey relational analysis coupled with firefly algorithm for multiobjective optimization of wire electric discharge machining. Proc IMechE, Part B: J Engineering Manufacture2015; 229: 1385–1394.
28.
WangDCaiK. Optimizing the static–dynamic performance of the body-in-white using a modified non-dominated sorting genetic algorithm coupled with grey relational analysis. Eng Optim2018; 50: 615–633.
29.
WangDWangS. Multi-objective lightweight design of the container S-beam based on MNSGA-II with grey relational analysis. Proc IMechE, Part C: J Mechanical Engineering Science2019; 0: 1–12.
30.
ZhouJRenJYaoC. Multi-objective optimization of multi-axis ball-end milling Inconel 718 via grey relational analysis coupled with RBF neural network and PSO algorithm. Meas J Int Meas Confed2017; 102: 271–285.
31.
ZhangNShiY. Improvement of cutting force and material removal rate for disc milling TC17 blisk tunnels using GRA–RBF–PSO method. Proc IMechE, Part C: J Mechanical Engineering Science2019; 0: 095440621984847.
32.
KrishnanMSubramaniamS. Multi-response optimization of friction stir corner welding of dissimilar thickness AA5086 and AA6061 aluminum alloys by Taguchi grey relational analysis. Proc IMechE, Part C: J Mechanical Engineering Science2018; 0: 1–10.
33.
GajalakshmiKSenthilkumarNPrabuB. Multi-response optimization of dry sliding wear parameters of AA6026 using hybrid gray relational analysis coupled with response surface method. Meas Control2019.
34.
RajeshSDevarajDSudhakara PandianR, et al.Multi-response optimization of machining parameters on red mud-based aluminum metal matrix composites in turning process. Int J Adv Manuf Technol2013; 67: 811–821.
35.
LuHSChangCKHwangNC, et al.Grey relational analysis coupled with principal component analysis for optimization design of the cutting parameters in high-speed end milling. J Mater Process Technol2009; 209: 3808–3817.
36.
FungCPKangPC. Multi-response optimization in friction properties of PBT composites using Taguchi method and principle component analysis. J Mater Process Technol2005; 170: 602–610.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
