In this paper, the Taguchi method has been used to optimize cutting parameters in the turning of Ti6Al4V/Al7050 laminates under elliptical vibration cutting. The turning tests were conducted based on L16 orthogonal array, which was designed by the Taguchi method. The analysis of variance was used to calculate impacts of cutting parameters on cutting forces and temperature. The analysis of results showed that the vibration frequency is the dominant factor on the cutting force and the vibration amplitude is a dominant factor affecting the temperature. The analysis of variance was also used to predict the cutting force and temperature in the turning of Ti6Al4V/Al7050 laminate. A good agreement between the predicted and the actual value can be found in the results.
XuJEl MansoriM. Wear characteristics of polycrystalline diamond tools in orthogonal cutting of CFRP/Ti stacks. Wear2017; 376: 91–106.
2.
SuiXDQinXSYuHD, et al.Relationship of microstructure, mechanical properties and titanium cutting performance of TiAlN/TiAlSiN composite coated tool. Ceram Int2016; 42: 7524–7532.
3.
KahwashFShyhaIMaheriA. Meshfree formulation for modelling of orthogonal cutting of composites. Compos Struct2017; 166: 193–201.
4.
WeiLWangD. Comparative study on drilling effect between conventional drilling and ultrasonic-assisted drilling of Ti-6Al-4V/Al2024-T351 laminated material. Int J Adv Manuf Technol 2019. Epub ahead of print. DOI: 10.1007/s00170-019-03507-6.
5.
Xu J, El Mansori M and Voisin J. Numerical modeling and FE analysis of CFRP/Ti stack orthogonal cutting. In: Wertheim R, Ihlefeldt S, Hochmuth C and Putz M (eds) 7th HPC 2016 - CIRP conference on high performance cutting, Chemnitz, Germany, 31 May-2 June 2016, pp.67–70.
6.
ShiXHussainGButtSI, et al.The state of residual stresses in the Cu/Steel bonded laminates after ISF deformation: an experimental analysis. J Manuf Process2017; 30: 14–26.
7.
XuJMansoriME. Experimental studies on the cutting characteristics of hybrid CFRP/Ti composite. Procedia Manuf2016; 5: 270–281.
8.
MathivananNRMaheshBSShettyHA. An experimental investigation on the process parameters influencing machining forces during milling of carbon and glass fiber laminates. Measurement2016; 91: 39–45.
9.
ArameshMAttiaMHKishawyHA, et al.Estimating the remaining useful tool life of worn tools under different cutting parameters: a survival life analysis during turning of titanium metal matrix composites (Ti-MMCs). CIRP J Manuf Sci Technol2016; 12: 35–43.
10.
Aramesh M, Shaban Y, Balazinski M, et al. Survival life analysis of the cutting tools during turning titanium metal matrix composites (Ti-MMCs). In: Dornfeld D and Helu M (eds) 6th CIRP international conference on high performance cutting, Berkeley, CA, 23-25 June 2014, pp.605–609.
11.
Aramesh M, Shi B, Nassef AO, et al. Meta-modeling optimization of the cutting process during turning titanium metal matrix composites (Ti-MMCs). In: Settineri L (ed.) 14th CIRP conference on modeling of machining operations, Torino, Italy, 13-14 June 2013, pp.576–581.
12.
SuiHZhangXZhangD, et al.Feasibility study of high-speed ultrasonic vibration cutting titanium alloy. J Mater Process Technol2017; 247: 111–120.
13.
NiCZhuLLiuC, et al.Analytical modeling of tool-workpiece contact rate and experimental study in ultrasonic vibration-assisted milling of Ti–6Al–4V. Int J Mech Sci2018; 142–143: 97–111.
14.
YangZZhuLNiC, et al.Investigation of surface topography formation mechanism based on abrasive-workpiece contact rate model in tangential ultrasonic vibration-assisted CBN grinding of ZrO2 ceramics. Int J Mech Sci2019; 155: 66–82.
15.
YangZZhuLLinB, et al.The grinding force modeling and experimental study of ZrO2 ceramic materials in ultrasonic vibration assisted grinding. Ceram Int2019; 45: 8873–8889.
16.
GengDZhangDLiZ, et al.Feasibility study of ultrasonic elliptical vibration-assisted reaming of carbon fiber reinforced plastics/titanium alloy stacks. Ultrasonics2017; 75: 80–90.
17.
Bai W, Sun R and Leopold J. Numerical modelling of microstructure evolution in Ti6Al4V alloy by ultrasonic assisted cutting. In: Wertheim R, Ihlefeldt S, Hochmuth C and Putz M (eds) 7th HPC 2016 - CIRP conference on high performance cutting, Stadthalle Chemnitz, Chemnitz, Germany, 31 May-2 June 2016, pp.428–431.
18.
BaiWSunRLeopoldJ, et al.Microstructural evolution of Ti6A14V in ultrasonically assisted cutting: numerical modelling and experimental analysis. Ultrasonics2017; 78: 70–82.
19.
KarabulutS. Optimization of surface roughness and cutting force during AA7039/Al2O3 metal matrix composites milling using neural networks and Taguchi method. Measurement2015; 66: 139–149.
20.
FEM AE. User’s manual. Version 6.0. 2013.
21.
WangBLiuZSongQ, et al.Proper selection of cutting parameters and cutting tool angle to lower the specific cutting energy during high speed machining of 7050-T7451 aluminum alloy. J Clean Prod2016; 129: 292–304.
22.
Ozkutuk M and Kaynak Y. The effect of material parameters on chip formation in orthogonal cutting simulation of Ti-5553 Alloy. In: Outeiro J and Poulachon G (eds) 16th CIRP conference on modelling of machining operations, Cluny, France, 15-16 June 2017, pp.305–310.
23.
OezelTZerenE. Finite element modeling the influence of edge roundness on the stress and temperature fields induced by high-speed machining. Int J Adv Manuf Technol2007; 35: 255–267.
24.
TanJQZhanMLiuS, et al.A modified Johnson-Cook model for tensile flow behaviors of 7050-T7451 aluminum alloy at high strain rates. Mater Sci Eng A2015; 631: 214–219.
25.
WanLWangDGaoY. The investigation of mechanism of serrated chip formation under different cutting speeds. Int J Adv Manuf Technol2016; 82: 951–959.
26.
AsilturkIAkkusH. Determining the effect of cutting parameters on surface roughness in hard turning using the Taguchi method. Measurement2011; 44: 1697–1704.
27.
KosarajuSChandrakerS. Taguchi analysis on cutting force and surface roughness in turning MDN350 steel. Mater Today-Proc2015; 2: 3388–3393.
