In this paper, the flow in the impeller sidewall gap of a low specific speed centrifugal pump is analyzed to study the effect of wear ring clearance and the resultant through-flow on flow field in this cavity and investigate the overall efficiency of the pump. Centrifugal pumps are commonly subject to a reduction in the flow rate and volumetric efficiency due to abrasive liquids or working conditions, since the wear rings are progressively worn, the internal leakage flow is increased. In the new operating point, the overall efficiency of the pump cannot be predicted simply by using the pump characteristic curves. The flow field is simulated with the use of computational fluid dynamics and the three-dimensional full Navier–Stokes equations are solved using CFX software. In order to verify the numerical simulations, static pressure field in volute casing and pump performance curves are compared with the experimental measurements. The results show that, for the pump with minimum wear ring clearance, the disk friction efficiency is the strongest factor that impairs the overall efficiency. Therefore, when the ring clearance is enlarged more than three times, although volumetric efficiency decreases effectively but the reduction in overall efficiency is remarkably smaller due to improvement in the disk friction losses.
GülichJF. Centrifugal pumps, New York: Springer, 2008.
2.
KármánTv. Über laminare und turbulente Reibung. Appl Math Mech/Zeit Angew Math Mech1921; 1: 233–252.
3.
GregoryNStuartJWalkerW. On the stability of three-dimensional boundary layers with application to the flow due to a rotating disk. Philos Trans Roy Soc Lond A1955; 248: 155–199.
4.
Owen JM. Flow between a rotating and a stationary disc. Thesis, University of Sussex, UK, 1969.
5.
DorfmanL. Resistance of a rotating rough disc. Zh Tekh Fiz1958; 28: 380–386.
6.
Schultz GrunowF. Der Reibungswiderstand rotierender Scheiben in Gehäusen. J Appl Math Mech/Zeit Angew Math Mech1935; 15: 191–204.
7.
PantellK. Versuche über Scheibenreibung. Forsch Gebiete Ingenieur1949; 16: 97–108.
8.
DailyJWNeceRE. Chamber dimension effects on induced flow and frictional resistance of enclosed rotating disks. J Basic Eng1960; 82: 217–230.
9.
KurokawaJToyokuraTShinjoMet al.Roughness effects on the flow along an enclosed rotating disk. Bull JSME1978; 21: 1725–1732.
10.
ItohMYamadaYImaoSet al.Experiments on turbulent flow due to an enclosed rotating disk. Exp Therm Fluid Sci1992; 5: 359–368.
11.
WilsonMPilbrowROwenJM. Flow and heat transfer in a preswirl rotor–stator system. J Turbomach1997; 119: 364–373.
12.
SerreEBontouxPLaunderB. Direct numerical simulation of transitional turbulent flow in a closed rotor-stator cavity. Flow Turbul Combust2002; 69: 35–50.
13.
Chew J, Green T and Turner A. Rim sealing of rotor-stator wheelspaces in the presence of external flow. In: ASME 1994 international gas turbine and aeroengine congress and exposition. New York: American Society of Mechanical Engineers, 1994, pp.V001T01A41–VT01A41.
14.
LaunderBPoncetSSerreE. Laminar, transitional, and turbulent flows in rotor-stator cavities. Annu Rev Fluid Mech2010; 42: 229–248.
15.
CrosAFlorianiELe GalPet al.Transition to turbulence of the Batchelor flow in a rotor/stator device. Eur J Mech B/Fluids2005; 24: 409–424.
16.
PoncetSSerreÉLe GalP. Revisiting the two first instabilities of the flow in an annular rotor-stator cavity. Phys Fluids2009; 21: 064106–064106.
17.
PoncetSChauveM-PLe GalP. Turbulent rotating disk flow with inward throughflow. J Fluid Mech2005; 522: 253–262.
18.
GülichJ. Disk friction losses of closed turbomachine impellers. Forsch Ingenieur2003; 68: 87–95.
19.
NemdiliAHellmannD. Investigations on fluid friction of rotational disks with and without modified outlet sections in real centrifugal pump casings. Forsch Ingenieur2007; 71: 59–67.
20.
AnderssonHILygrenM. LES of open rotor–stator flow. Int J Heat Fluid Flow2006; 27: 551–557.
21.
DebuchyRNourFABoisG. On the flow behavior in rotor-stator system with superposed flow. Int J Rotat Mach2008, pp. 2008–2008.
22.
DebuchyRNourFANajiHet al.Investigation of the fluid flow in an isolated rotor-stator system with a peripheral opening. Sci China Phys Mech Astron2013; 56: 745–754.
23.
Nour FA, Debuchy R and Bois Gr. Influence of a weak superposed centripetal flow in a rotor-stator system for several pre-swirl ratio. In: ASME-JSME-KSME 2011 joint fluids engineering conference. New York: American Society of Mechanical Engineers, 2011, pp.2921–2929.
24.
Poncet S, Da Soghe R and Facchini B. RANS modeling of flow in rotating cavity system. In: V European conference on computational fluid dynamics (ECCOMAS CFD 2010), Lisbon, Portugal, 2010.
25.
WillB-CBenraF-KDohmenH-J. Investigation of the flow in the impeller side clearances of a centrifugal pump with volute casing. J Therm Sci2012; 21: 197–208.
26.
LiW-G. Model of flow in the side chambers of an industrial centrifugal pump for delivering viscous oil. J Fluids Eng2013; 135: 051201–051201.
27.
LiW-G. An experimental study on the effect of oil viscosity and wear-ring clearance on the performance of an industrial centrifugal pump. J Fluids Eng2012; 134: 014501–014501.
28.
XuLLuW-gLuL-get al.Flow patterns and boundary conditions for inlet and outlet conduits of large pump system with low head. Appl Math Mech2014; 35: 675–688.
29.
CaoLZhangYYWangZWet al.Effect of axial clearance on the efficiency of a shrouded centrifugal pump. J Fluids Eng2015; 137: 071101–071101.
30.
MohamedSNChewJHillsN. Flow and windage due to bolts on a rotating disc. Proc IMechE, Part C: J Mechanical Engineering Science2016. DOI: 0954406216642260.
31.
GaoXShiWZhouLet al.Computational fluid dynamics and experimental study of inter-stage seal clearance on submersible well pump. Adv Mech Eng2016. DOI: 1687814016632680.
32.
AlemiHNourbakhshSARaiseeMet al.Effects of volute curvature on performance of a low specific-speed centrifugal pump at design and off-Design conditions. J Turbomach2015; 137: 041009–041009.
33.
AlemiHAhmad NourbakhshSRaiseeMet al.Development of new “multivolute casing” geometries for radial force reduction in centrifugal pumps. Eng Appl Comput Fluid Mech2015; 9: 1–11.
34.
ZhangDShiWvan EschBBet al.Numerical and experimental investigation of tip leakage vortex trajectory and dynamics in an axial flow pump. Comput Fluids2015; 112: 61–71.
35.
LiuYTanLHaoYet al.Energy performance and flow patterns of a mixed-flow pump with different tip clearance sizes. Energies2017; 10: 191–191.
36.
CicciottiMXenosDPBouaswaigAEet al.Physical modelling of industrial multistage centrifugal compressors for monitoring and simulation. Proc IMechE, Part C: J Mechanical Engineering Science2015; 229: 3433–3448.
37.
LiXZhuZLiYet al.Experimental and numerical investigations of head-flow curve instability of a single-stage centrifugal pump with volute casing. Proc IMechE, Part A: J Power and Energy2016; 230: 633–647.
38.
CommitteeV. Standard for verification and validation in computational fluid dynamics and heat transfer, New York: American Society of Mechanical Engineers, 2009.
39.
Juckelandt K and Wurm F-H. Applicability of wall-function approach in simulations of turbomachines. In: ASME turbo expo 2015: Turbine technical conference and exposition. New York: American Society of Mechanical Engineers, 2015, pp.V02BT39A001–V02BT39A.
40.
Wang Y and Wang W. Applicability of eddy viscosity turbulence models in low specific speed centrifugal pump. In: IOP conference series: Earth and environmental science. Bristol, UK: IOP Publishing, 2012, p. 062013.
41.
NejadrajabaliJRiasiANourbakhshS. Flow pattern analysis and performance improvement of regenerative flow pump using blade geometry modification. Int J Rotat Mach2016. DOI: 10.1155/2016/8628467.
42.
WhiteFMCorfieldI. Viscous fluid flow, New York: McGraw-Hill, 2006.
43.
SchlichtingHGerstenKKrauseEet al.Boundary-layer theory, New York: Springer, 1960.
44.
CaoLWangZXiaoYet al.Numerical investigation of pressure fluctuation characteristics in a centrifugal pump with variable axial clearance. Int J Rotat Mach2016.
45.
ChalghoumIKanfoudiHElaoudSet al.Numerical modeling of the flow inside a centrifugal pump: Influence of impeller–volute interaction on velocity and pressure fields. Arab J Sci Eng2016(41): 4463–4476.
46.
DIN EN 9906. Rotodynamic pumps-hydraulic performance acceptance tests - Grades 1 and 2. Geneva: International Standardization Organization, 1999.
