Accuracy analysis of a multi-closed-loop deployable mechanism

Abstract

The multi-closed-loop deployable mechanism generates distortion which is caused by the deviation of each rod after being assembled as a result of manufacturing error, which leads to the degradation of the antenna performance or excess of the given envelope. The multi-closed-loop deployable mechanisms consist of many closed loops and have complicated topology structure and loop constraints coupling. The positioning accuracy analysis of such mechanism is more difficult than the open-chain mechanisms or the single-loop mechanisms. In order to solve this problem, first, based on the minimum of elastic deformation energy, the distortion analysis model is constructed. Second, the sensitivity of the mechanism distortion to the individual rod deviation is investigated by examining the Lagrange multipliers. By means of this model, the allowable tolerance of multi-closed-loop deployable mechanism is discussed and calculated. Last but not least, the above method and model are applied to the four-closed-loop deployable mechanism to solve the problems of its distortion, sensitivity, and tolerance in both fully deployed and folded configurations. It is demonstrated in this paper that the model and method proposed are well accommodated to the accuracy analysis of such mechanisms. The achievement of the research will help reduce the difficulties of the assembling and manufacturing of the multi-closed-loop deployable mechanisms.

Keywords

Deployable mechanisms modeling design parameters design for manufacture mechanical design

Get full access to this article

View all access options for this article.

References

Thomas

. RADARSAT-2 extendible support structure. Can J Remote Sens 2004; 30: 282–286.

Gralewski MR, Adams L and Hedgepeth JM. Deployable extendable support structure for the RADARSAT synthetic aperture radar antenna. In: Forty-third International Astronautical Congress, Washington, USA, 28 August–5 September 1992, pp.18–24, Washington: IAF.

Jurgen LH, Christian EC and Rudolf W. Design and verification of mechanisms for a large foldable antenna. In: Twenty-third aerospace mechanisms symposium. Huntsville, USA: Marshall Space Flight Center, 1989, pp.113–126.

Jordan

. The SEASAT-A synthetic aperture radar system. IEEE J Oceanic Eng 1980; 5: 154–164.

JPL History. Seasat's synthetic aperture radar antenna, http://www.jpl.nasa.gov/jplhistory/captions/seasatradar-t.php (2012, accessed 22 February 2014).

Wei

Dai

. A Spatial eight-bar linkage and its association with the deployable platonic mechanisms. Trans ASME J Mech Robotics 2014; 6: 021010–1-9.

Wei

Chen

Dai

. Synthesis, mobility and multifurcation of deployable polyhedral mechanisms with radially reciprocating motion. Trans ASME J Mech Des 2014; 136: 091003–1-12. .

Wei

Dai

. Reconfigurable and deployable platonic mechanisms with a variable revolute joint. In: Lenarcic J and Khatib O (eds) Advances in robot kinematics, 1st ed. Switzerland: Springer, 2014, pp. 485–495. .

Wei

Ding

Dai

. Mobility and geometric analysis of the Hoberman switch-pitch ball and its variant. Trans ASME J Mech Robotics 2010; 2: 031010–1-9.

10.

Deng

Huang

. Synthesis of deployable/foldable single loop mechanisms with revolute joints. Trans ASME J Mech Robotics 2011; 3: 031006–1-12.

11.

Chen

You

. On mobile assemblies of Bennett linkages. Proc R A Soc 2008; 464: 1275–1293.

12.

Chen

You

Tarnai

. Threefold-symmetric Bricard linkages for deployable structures. Int J Solids Struct 2005; 42: 2287–2301.

13.

Ding

Yang

Dai

. Design and kinematic analysis of a novel prism deployable mechanism. Mech Mach Theory 2013; 63: 35–49.

14.

Hiller M, Kecskemethy A and Woernle C. A loop-based kinematical analysis of complex mechanisms. In: Design engineering technical conference, Ohio, USA, 5–8 October 1986, Paper 86-DET-184. New York: ASME.

15.

Wang DD, Liu RQ, Wang Y, et al. Deployment analysis of a planar deployable support truss structure. In: Proceedings of 2013 IEEE International Conference on Mechatronics and Automation, Takamatsu, Japan, 4–7 August 2013, pp.1287–1292, Piscataway: IEEE.

16.

Anantharaman

Hiller

. Numerical simulation of mechanical systems using methods for differential-algebraic equations. Int J Numer Methods Eng 1991; 32: 1531–1542.

17.

Gosselin

Angeles

. Singularity analysis of closed-loop kinematic chains. IEEE Trans Robotics Automat 1990; 6: 281–290.

18.

Weeks

. Dynamic analysis of a deployable space structure. J Spacecraft Rockets 1986; 23: 102–107.

19.

Guo

Cao

. Dynamic characteristics analysis of deployable space structures considering joint clearance. Acta Astronaut 2011; 68: 974–983.

20.

Hedgepeth

. Influence of fabrication tolerances on the surface accuracy of large antenna structure. AIAA 1982; 20: 680–686.

21.

Mobrem M. Methods of analyzing surface accuracy of large antenna structures due to manufacturing tolerances. In: 44th AIAA/ASME/ASCE/AHS/ASC structures, structural dynamics, and materials conference, Virginia, USA, 7–10 April 2003, pp.1–10. Maryland: AIAA.

22.

Rajputpage

. A textbook of manufacturing technology: manufacturing processes, New Delhi, India: Firewall Media, 2008, pp. 705..

23.

Avilés

Hernández

Amezua

. Kinematic analysis of linkages based in finite elements and the geometric stiffness matrix. Mech Mach Theory 2008; 43: 964–983.