A calculating model for roller-pocket rotation and mechanics analysis is established to investigate the hydrodynamic lubrication between rollers and straight-sided cage pockets in a cylindrical roller bearing. An algorithm for calculating roller-pocket oil film pressure and film thickness is developed. Hydrodynamic lubrication simulation of the roller-pocket clearances is carried out. Effects of inner ring rotation speed, cage angular acceleration, roller profile and cage geometry on roller-pocket oil film performance are numerically studied. Some regular curves and conclusions are obtained and analyzed.
WoodaRAE. Rolling bearing cages. Tribol1972; 5: 14–21.
2.
MolinaMAGoharR. Hydrodynamic lubrication of ball-bearing cage pockets. Proc IMechE, Part E: J Process Mechanical Engineering1978; 20: 11–20.
3.
Ye ZH, Wang LQ, Gu L, et al. Cage instabilities in high-speed cylindrical roller bearings. In: STLE/ASME international joint tribology conference, San Francisco, USA, 17–20 October 2010, pp.1–3. New York: ASME.
4.
SakaguchiTHaradaK. Dynamic analysis of cage behavior in a tapered roller bearing. J Tribol2006; 128: 604–611.
5.
HarrisTAKotzalasMN. Rolling bearing analysis: advanced concepts of bearing technology, 5th ed. New York: CRC Press, 2006, pp. 117–135.
MeeksCRNgKO. The dynamics of ball separators in ball bearings–part I: analysis. Tribol Trans1985; 28: 277–287.
9.
MeeksCRNgKO. The dynamics of ball separators in ball bearings–part II: results of optimization study. Tribol Trans1985; 28: 288–295.
10.
GentleCRPasdariM. Measurement of cage and pocket friction in a ball bearing for use in a simulation program. Tribol Trans1985; 28: 536–541.
11.
GuptaPK. Modeling of instabilities induced by cage clearances in cylindrical roller bearings. Tribol Trans1991; 34: 1–8.
12.
AshmoreDRWilliamsEJMcWilliamS. Hydrodynamic support and dynamic response for an inner-piloted bearing cage. Proc IMechE, Part G: J Aerospace Engineering2003; 217: 19–28.
13.
DamiensBLubrechtAACannPM. Influence of cage clearance on bearing lubrication. Tribol Trans2004; 47: 2–6.
14.
Cann PM and Lubrecht AA. Bearing performance limits with grease lubrication. In: World Tribology Congress III, Washington, D.C., USA, 12–16 September 2005.
DibAHaiahemA. FEM analysis of cage stress distribution: part 1: cylindrical roller bearing. J Eng Appl Sci2007; 2: 180–182.
17.
UpadhyaySHJainSCHarshaSP. Non-linear vibration signature analysis of high speed rotating shaft due to ball size variations and varying number of balls. Proc IMechE, Part K: J Multi-body Dynamics2009; 223: 83–105.
18.
PatelUAUpadhyaySH. Theoretical model to predict the effect of localized defect on dynamic behavior of cylindrical roller bearing at inner race and outer race. Proc IMechE Part K: J Multi-body Dynamics2014; 228: 152–171.
19.
TakabiJKhonsariMM. On the influence of traction coefficient on the cage angular velocity in roller bearings. Tribol Trans2014; 57: 793–805.
20.
WenSZHuangP. Principles of tribology, 3rd ed. Beijing: Tsinghua University Press, 2008, pp. 48–48.
21.
DowsonDMarkhoPHJonesDA. The lubrication of lightly loaded cylinders in combined rolling, sliding and normal motion–part I: theory. J Lubr Tech1976; 98: 509–516.
22.
Zhou Q. Research on the lubrication performance of lip seal and the influence on the rotor dynamics performance. PhD Thesis, East China University of Science and Technology, China, 2013.
23.
ZhouQLiZMSangSJ. A numerical simulation method for hydrodynamic lubrication of lip seal. Proc IMechE Part J: J Engineering Tribology2011; 226: 99–110.
24.
HarrisTAKotzalasMN. Rolling bearing analysis: essential concepts of bearing technology, New York: CRC Press, 2006, pp. 182–184.
25.
Bhushan B. Introduction to tribology. 2nd ed. New York: John Wiley & Sons, 2013, pp.409–410.
